12" Car and Trailer End Loop

Ask the Experts about this Spectro Wiring
Do you have a question about this Wiring?

• Recommended Parts and Wiring for Adding LED Lights to Aluminum Cargo Carrier with Ramp
  
• Thank you for all of the helpful information! I do have a few different options for you to add LED lighting to your scooter carrier that resembles the MaxxTow 27x47 Cargo Carrier # MT70100. You can definitely use the Optronics Streamline LED Trailer Tail Light # STL79RB with wiring like the Hopkins Endurance # HM38134 by just using heat shrink butt connectors # DW05744-5. Since your carrier is aluminum you will need to cut off the eyelet on the ground wire and splice it to the white...
  view full answer...


• Hitch Cargo Carrier, Lighting Kit, Cargo Net and Wiring for 2017 Subaru Outback Wagon
  
• We can help you get your 2017 Subaru Outback ready for some cargo hauling using its factory-installed 1-1/4-inch hitch. The cargo carrier you referenced, the Pro Series # 63153, only fits a larger 2-inch size hitch but we have similar carriers you can use in your 1-1/4-inch OEM hitch, such as their model # 63155. Do note though that those factory Subaru hitches do not have the same weight carrying capacity as the 2-inch aftermarket hitches we offer that can bolt right up to the car's...
  view full answer...


• Lights And Accessories for Using Curt # C18153 Cargo Carrier on 2014 Chevy Suburban
  
• The only difference between the two anti-rattle hitch locks you referenced is that the # 63232 is for 2 inch receivers and the # SHP2040-XL is for 2-1/2 inch receivers. Since your Suburban has the 2 inch receiver, you'd need the # 63232. If the 4 pole on your Suburban is fixed in place on the bumper, I'd recommend the # 9653P extension. The Curt # C18153 you're referring to isn't specifically designed for a light kit, so they're aren't any pre-drilled holes on the carrier to mount...
  view full answer...


• Available 4-Pole and 7-Way Trailer Wiring Extensions
  
• We do offer many types of trailer wiring extensions. For 4-pole flat trailer wiring you can use 4-foot extension # HM47115 or 1-foot part # 9653P. For 7-way trailer wiring we have 28-inch extension # TLW6028, 21-inch # TLW6021 or one of the others shown on the linked page.
  view full answer...


• RV has 7 Way and Need to Connect 4 Way for Dolly and 4 Way for Tow Lights to Use at the Same Time
  
• I have a solution for you. We do not have any type of Y adapter but I do have the parts available to allow you to connect both 4 wire flat plugs at the same time. I do recommend that you first check to ensure that you will not be drawing too many amps on the circuit by using both the dolly wiring and the tow lights together. You will need the following products: Car and Trailer End Loop, # 9653P Qty 2 Pollack 7-Pole Trailer Connector, # PK12706 Qty 1 First you will start by cutting...
  view full answer...


• Isolating Power for a 5-Wire Motorcycle Trailer Harness and a 5-Wire Motorcycle Trailer
  
• There is a way to isolate the power draw on a 5 wire to 5 wire setup, but it would require a few parts and some wiring work. All of the isolated power trailer converters convert a 5-wire vehicle to a more standard 4-wire system for automotive use trailers, but as you are aware, motorcycle trailers are built as 5-wire systems to match the bike. You would use part # 119179 on the bike. This part has 5 wire leads to connect ground and the different light functions. The 6th wire is the battery...
  view full answer...


• Installing MaxxTow # MT70097 Magnetic Mount Tow Lights Permanently on Vehicle
  
• The MaxxTow Magnetic Tow Lights you mentioned # MT70097 could be modified by doing some cutting and splicing to work as you describe. You would attach the connector of the wiring harness at the front of the vehicle and run the wiring under the vehicle. Following the frame member or an existing wiring harness works best. Run the wires to the rear of the vehicle, being sure to avoid any suspension and steering components that might move or anything hot like the exhaust system. Under the...
  view full answer...


• Recommended Trailer Light Kit to Add to the Curt Cargo Carrier # C18153
  
• You are definitely correct. Anytime some equipment that you are carrying is blocking the lights on your Chevy Equinox it can result in dangerous situations let alone a friendly visit from a Police Officer. Some great lights that you can add to your Curt Cargo Carrier # C18153 is the Let's Go Aero LED Light Kit # 98174LED. These can be installed on your cargo carrier by using the Mounting Bracket # BK70BB and Self Tapping Screw # FA1131822. The overall length of the offset y-harness wire...
  view full answer...


• How to Extend a Trailer Wire 4-way by 12 Inches
  
• If I am understanding you correctly you have a 4-way on your 2012 Toyota Highlander but you are looking for a way to extend the wiring of the 4-way by 12 inches. What I would recommend you get would be a 12 inch Car and Trailer End Extension # 9653P. This product will extend your 4-way by exactly 12 inches and should work well for you.
  view full answer...


• Light Kit and License Plate Bracket Recommendation for the 19x47 Curt Cargo Carrier
  
• For the 19x47 Curt Cargo Carrier # C18110 I recommend using the Light Kit # 20174 with 2 of the Mounting Bracket # BK70BB and the Optronics LED Trailer License Plate Light with Bracket # LPL56CB. You will need to connect the black wire from the license plate light to the brown wire of the wiring harness that comes with the light kit. You may also need an extension like part # 9653P to reach the 4-Way Flat connector on your vehicle. Please note that there isn't a light kit that is designed...
  view full answer...


• 4-Way Extension Wire Recommendation for Bully Dodge Ram Hitch Cover # CR-007D
  
• Best option for a 4-way extension for use with the # CR-007D would be the part # 9653P. This is a 12 inch long extension that will give you just enough extra wire without adding too much wire.
  view full answer...


• Availability of Just 4-Way Connectors
  
• What harness are you looking for? Like a 4-way that comes on part # 002220? We have the part # 48195 as well or the part # 9653P that comes with both sides plus wiring if needed. You would just cut the middle of the wiring and would have wire for both sides.
  view full answer...


• Availability of 4-Way Square Connector for Wiring a Ford 3600 Tractor
  
• If you will be needing to connect and disconnect the plugs more often I would recommend just to remove the 4-Way square on each end and wire in the 12 Inch Car and Trailer End Loop, part # 9653P. You will just need to cut the # 9653P loop in half and wire each end to the wires that remain from removing of the 4-Way square connectors.
  view full answer...


• Recommended Safety Chains and 4-Pin Tow Wiring Connector Extender for a 2003 Toyota 4Runner
  
• Thanks for your purchase from etrailer! I would go with the Hopkins 4-pole loop with cover # HM47115 because it will extend your current 4-way connector 48-inches (4 feet). If that is too long, we currently offer a 12-inch extension # 9653P. If you plan on using these extensions permanently, then I would use some dielectric grease between the connections # 11755. Then use zip ties to hold connections together and electrical tape to wrap it all up to protect it from the elements. A...
  view full answer...


• What LED Lighting Kit Fits ProSeries 24x60 Steel Hitch-Mount Cargo Carrier # 63153
  
• The ProSeries 24x60 Steel Hitch-Mount Cargo Carrier # 63153 that you referenced can use either an incandescent or an LED-type lighting kit. The LED lighting kit, part # 98174LED, includes the set of two 12-diode oval lights, rubber mounting grommets and wiring. An extension is offered, part # 9653P, which gives you an additional 12-inches of wiring length. Efficient LED lighting uses only about 1/10th of the power required by incandescent lights like # 20174 and they also offer brighter...
  view full answer...


• Troubleshooting Trailer Running Lights Not Working on Trailer
  
• I checked your order notes and it looks like you ordered part numbers # 9653P, # HM48192, and # HM48190. It could be as simple as a bad ground that is causing the running lights to now work, but since the bulb was blown that would more indicate a short on the wiring of the circuit somewhere. Check the wiring of the circuit for any exposed or cut wire and fix as necessary. I realize that's the last thing anyone wants to do in the cold but that is most likely the problem. The way you have...
  view full answer...


• Parts Needed to Make a Brake Controller Portable Between a Toyota and a Jeep
  
• At this time we do not carry the vehicle side of the Brake Control Wiring Adapters for an installation application like you are suggesting. But, I do have a recommendation for you. You could use a 12 inch Car and Trailer End Loop, item # 9653P, and wire the brake controller wiring to this. You would want to attach the vehicle side connector, 3 protected poles and exposed ground pole, to the vehicle and the trailer side to the wiring from the brake controller. You would then need another...
  view full answer...


• Does Ram Lighted Hitch Cover 86066 Blink when Turn Signals are On
  
• The little converter mentioned is included with the Ram LED Lighted Trailer Hitch Cover - 1-1/4" and 2" Hitches - Chrome Item # 86066. It separates out the turn signals so the cover does not light up when you have either blinker activated. You would not need to purchase any other converter. Some people have found the wiring on this hitch cover is not long enough to plug into the factory 4-Way trailer connector on the back of the vehicle. Extension # 9653P is recommended in those situations.
  view full answer...


• What Accessories Can Be Used With the Pro Series Cargo Carrier 63153 on a 2001 Nissan Xterra SE
  
• The 24x60 Pro Series Cargo Carrier, part # 63153, will work great in the 2 inch trailer hitch receiver at the rear of your 2001 Nissan Xterra SE. This cargo carrier has a 2-1/2 inch shank rise so any equipment should be clear of your muffler, which means it will be safe to use on your Xterra. To mount your license plate on the cargo carrier you can use Mounting Bracket # LP10SB. We offer 2 different light kits that fit perfectly on the Pro Series carrier. You can use either the Light...
  view full answer...


• Wiring Harness for 2015 Land Rover Evoque to Connect to Lights on Bike Rack
  
• In order to connect the LED Light Kit # 98174LED to your 2015 Land Rover Evoque you will need a trailer wiring harness with a 4-Way flat trailer connector, such as the ZCI Circuit Protected Vehicle Wiring Harness with 4-Way Flat Trailer Connector and Installation Kit # 119250KIT. This wiring harness will install on your Evoque without requiring you to cut or splice into the factory wiring on your vehicle. The harness has zero-contact interface sensors that read the signals of the factory...
  view full answer...


• Recommended Cargo Hitch Carrier for a 2014 Ford Escape
  
• I have two different recommendations for a hitch cargo carrier that should sit above the exhaust on your 2014 Ford Escape. The first recommendation that I have is the Surco Carrier, part # 52018F. This is a 500 lbs carrier that is folding and has a 4 inch rise. Since none of our cargo carriers come with lights pre-installed, you will need to use the Light Kit # 52014 with this option. Also, installing lights on a cargo carrier is very easy, much easier than on a car and there is no cutting,...
  view full answer...


• Can Spectro 4-Pole 12-Inch Car and Trailer End Loop # 9653P Be Used as a Wiring Harness Extension
  
• The Spectro 4-Pole 12-Inch Car and Trailer End Loop # 9653P is a perfect solution for cases where trailer wiring is just a bit too short. We also offer a 4-foot # HM47115 from Hopkins.
  view full answer...


• Pro Series 63153 Cargo Carrier and Accessories for 2015 Subaru Outback
  
• You can certainly load the Pro Series # 63153 up a few feet, but as you said, you'll want to stay under the roof line. I'd highly recommend the # 59516 light kit and the # 9653P 12 inch extension. Keep in mind that the # 63153 is only compatible with 2 inch receivers. Your cargo can be held in place with a cargo net or tie down straps, depending on what you're carrying. I've linked you to the straps and nets we have available. A locking hitch pin like part # 40107 would be a great...
  view full answer...


• Are Car and Trailer End Loops # 9653P and # 18044 Each One Piece of Wire of Two Pieces
  
• The Car and Trailer End Loop, # 9653P, is one l2 inch long piece, just as it appears in the picture. The Car and Trailer End Loop 4-Pole, # 18044, is also one 48 inch long piece. It comes with quick splices in case one of the 4-Way connectors needs to be clipped off to splice bare wires. You can see this harness in use at about the 2 minute, 58 second mark of the video linked below.
  view full answer...


• Need 4-Pole Extension Wire for Cargo Carrier Light Kit # 52014
  
• We do offer a 4-foot extension wire equipped with 4-pole flat vehicle- and trailer-side connectors, part # 18044 from Draw-Tite. If this is longer than you need we also offer a 1-foot extension, part # 9653P, which also provides the same plug-in extension capability. No cutting or splicing is required for either extension. I recommend an application of dielectric grease on all connections when you install your light kit. We offer this (part # 11755) but it is also available locally at...
  view full answer...


• How Long is the Cord on the Ram LED Brake and Tail Light Trailer Hitch Cover, # 86066
  
• I went out to the warehouse and pulled a Ram LED Brake and Tail Light Trailer Hitch Cover, # 86066, to measure the length of the cord. It has an overall length of 16 inches. If that is not long enough to reach the trailer connector on your 2012 Dodge Ram, you could get an extension like # 9653P which will provide another 12 inches.
  view full answer...


• Parts Needed to Extend a 4-Way Trailer Connector
  
• You just need an extension loop like # HM47115 which is 48 inches long. If that is too long then we have a 12 inch extension # 9653P. If you want to make these extensions permanent then I recommend using some dielectric grease between the connections, # 11755, using zip ties to hold the connections together, and then using electrical tape to wrap it all up to protect it from the elements.
  view full answer...


• What Parts are Needed to Connect a 4-Pole Trailer to a 5-Pole Motorcycle
  
• If your bike is a 5-Way flat wired like most vehicle 5-Ways, then you could just plug the 4-Way trailer connector in. Obviously the 5th wire will have no connection which is fine. If the bike is a 5-Way round, there currently not any adapters available. You could make your own adapter using part # PK11501 and part # 9653P. You could also convert the trailer to a 5-Way round using just part # PK11501 and again omitting the 5th contact point since it is not needed on the trailer. If...
  view full answer...


• Folding Cargo Carrier that Lights Can be Added to on a 2017 Dodge Durango RT
  
• One option is the Surco Carrier # 52018F which is a folding 24 by 60 inch carrier. Lights can be added using # 52014. These install by connecting brackets to the uprights on the carrier. Another option is the Rola Dart Cargo Carrier # 59550 which is 23 by 56 inches. The light kit # 20174 installs into the cutout specifically designed into the carrier. You might need to extend the 4-way trailer connecter at the rear of your Durango to use the lights. You can use # 9653P for this.
  view full answer...


• Wiring A 2008 Toyota Highlander for Towing a 1996 Flagstaff Cobra Camper with 6-Way Square Connector
  
• Jayco uses a different wiring code than most, so in all likelihood, it will not work. I would just cut off the 6-Way square, tape off the brake and battery wires, and connect the 4 wires to a new 4-Way flat connector like part # 9653P. A better solution may be to install a more common 6-Way Round trailer connector on the vehicle and trailer. You could use the Pollak 6-Pole, Round Pin, Trailer Wiring Connector, item # PK11604, on the trailer end and a 4 Pole to 6 Pole Adapter, item #...
  view full answer...

Do you have a question about this Wiring?