To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Quickly and easily install a 4-way trailer connector on your Honda Odyssey with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's electrical junction box, which is located in your rear cargo area, beneath the trim panel on the passenger's side
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (182 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring - no cutting, splicing or tapping required.Product worked perfectly.. Easy to install!! Order came quickly! I appreciate all the supporting videos and info on the website!
Ordered it with hitch receiver. Delivered together, well packaged. Installation was simple. Followed video and everything went according to direction. Have not had opportunity to test it on trailer, but I'm confident it will work.
This is a great hitch! It's well made and bolted right onto my Honda Odyssey. I'm using my hitch to tow a small trailer for getting rid of yard debris. Now I don't have to go out and by a truck. This was very easy to install and it came with everything needed!
This was an easy to install product. I followed the instructions up to the placement of the end of the 4-pole connector. I routed mine into the bumper so I could leave a 7 pole connected to it more permanently.
The trailer hitch arrived and I'm really impressed the hitch is made of nice quality metal also the wiring is of quality not thin wiring or metal hitch very very happy
I love your website and doing business with you was about as good as any I’ve done anywhere. Plenty of helpful info, easy to search and navigate, checkout was straightforward. I sure wish other places were this helpful and easy (and fast!) Maybe you could market your platform and concepts...
Best of all, the product arrived fast, in good condition, and installed exactly as described. Oh yeah, love the detail and variety of the videos too!
Thanks again!
Ian - 01/22/2020Shipped on time. Arrived when expected. Instructional videos spot-on installation was straightforward. The only discrepancy was 7.5 amp fuse noted in the videos but at 10 and included for the fuse panel instead of a 7.5. I installed 10 amp and everything seemed to work out fine on my multimeter when I checked the circuit.
Great hitch and the wiring harness was easy to connect as well
I just love it . The hitch and wiring system took a little more than an hour to install . It looks great too ! I can't wait to use it . Thank you
I have a 2005 Odessey, this wiring harness was simple and made with high quality parts. I watched the install video and made it extremely easy to install. I called the Honda Dealership prior to seeing this item and there price was 4x higher and would take a week to get. I ordered this part and it was delivered in 2 business days.
Very Pleased with etrailer.com Thank you!
Jeff P - 05/03/2015I installed this wiring harness to my 2009 Honda Odyssey. The Curt wiring harness is quality built, a great price and very easy to install. The video was extremely helpful for visual learners like myself. The shipping was fast and the service from etrailer was exceptional.
Scott R - 10/20/2014
I purchased the trailer wiring kit for my 2010 Honda Odyssey.The ordering process, shipping, installation went well. haven't had any problem from beginning to now, 1 year later.
Jim L - 05/11/2021Very easy installation (plug and
Play) just follow video and had no problems!!
The times I used it have been great. I'm not planning to tow much with my van, but it's been good so far. I wired it so that it sits in the jack compartment in the back of the vehicle and it is easy to pull out and use as needed.
My sons, ages 11 and 13 installed it in about a half hour. They watched the video on their phones, I pointed to the tool chest in the garage.
A year later, the company is following through. I can’t think of a single important they could make.
Etrailer, great company.
This is the second harness I put in my Honda Odyssey. The instructions are clear and etrailets install video made this about a 15 minute job. My lights all work again and I'm a happy camper.
Tom G - 07/17/2018Incredibly easy to install, with the instructions it took me less than 10 minutes. The 4 pin connecter that goes to the trailer has enough wire that I was able to run it through the inside of the panels and keep the connecter inside the van when I am not using it keeping it from the weather and corrosion. I originally bought it so I could rent a uhaul trailer and the wire is long enough that I didn't need an extension to the 4 pin for the lights.
It was easy to install and I liked how it could be tucked away. For the first couple months it worked fine. Although now it no longer works properly,, I am not sure of the cause. It may have nothing to do with the quality of the kit. If I find that the kit can be replaced and it wasn't the cause I would then give it a higher rating. I didn't see any explanation for the problem which is the the brake power stays on and the right blinker side doesn't work at all. I already had the trailer checked to be sure it wasn't the problem and it works fine on a battery. I am still testing the vehicle side but vehicle lights all work fine.
Easy to install, great instructions, great product. I removed the taillight on the passenger side and drilled through the triple wall between the two vertical mounting bolts. I de-burred all 3 surfaces, and used grommets for the holes. I used a 1/2" hole and appropriate grommets (not included) to prevent wire chafing. I also split the wires into individual sections along that part to prevent binding when pulling through the holes. I measured about 12" from the Curt junction box and cut the wires so I didn't have to make a hole big enough to fit the plug into, (this may void the warranty, but I'm not pulling my paneling and dragging a wire out my tailgate every time I hook up a trailer.) I then dropped the plug down into the rear bumper compartment and fished it to my mounting bracket. I hooked everything else up as instructed. be careful not to chafe the wire pulling it through the holes or fishing it inside the bumper, and don't pinch it when re attaching the taillight. add electrical tape anyplace you "think" it may rub for extra protection. The whole thing took about 2.5 hours, but I have a well equipped shop and fabricate vehicles for a living, you might allow extra time, but nothing is really hard.
I just completed installation of the trailer light harness and I am very satisfied - it is working fine.
The only problem I encountered was likely due to ignoring the included instructions because I thought I knew enough watching the video on the internet showing installation in a 2010 Honda Odyssey which I have. Item number 4 of your instructions mentions the 10 amp (larger size) in-line fuse and I had ignored reading it. I finally "got smart" and found a soft rubbery, red "in-line fuse box" that is part of the wiring harness included in the kit that receives the 10-amp fuse.
Everything about your product is top-notch: materials, instructions, helpful personnel and thoughtful follow-ups. The completeness of your kit down to the little zip-locks leaves little to chance for human error.
Easy to install. Only used it a few times but works exactly as expected.
I know what good customer service looks and feels like ... and the folks at etrailer.com have some of the best customer service I've ever seen. Pretty awesome company and I appreciate everything they did to get me my trailer hitch and wiring in the time frame I needed it and for their constant and timely communications. They delivered as promised, and left me 100% satisfied and happy! HIGHLY RECOMMENDED!!
This wiring harness was easy to install and does exactly what it's supposed to do. It came with clear instructions and there were no surprises in the installation. etrailer.com had the part to me in the expected time frame. I used 2 day shipping to expedite my order so that I could use my trailer for a trip I had planned and I ordered on Friday and received it on Tuesday. Great products & Great service!
This wiring harness is one of the easiest trailer wiring harnesses I have ever installed. It plugs in the pre-existing board behind the rear passenger side panel, secure a ground wire, install 2 fuses and mount with provided double side tape and you are done. I would definitely buy this again. so much easier than chasing wires .
I purchased this wiring harness t be able to pull a small trailer with my 2006 Honda Odyssey. It was very easy to install (basically plug-n-play). It is hidden out of the way when not in use and works as expected when needed.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.