To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Install a 4-way trailer connector on your Toyota Camry with this wiring harness with tail light converter. Requires splicing into existing Toyota Camry wiring. Works with domestic and import Toyota Camrys. Includes wire taps.
Features:
Specs:
Included in Hardwire Kit:
Note: Requires install kit 55151 to help run wire to vehicle battery.
Because most trailers run on a 2-wire system - wherein the brake and turn signals are carried on 1 wire - the signals from your vehicle may have to be converted to be compatible with your trailer's wiring.
If your vehicle operates on a 3-wire system, which means that it has separate brake and turn signals, then those signals will need to be combined so that they run on 1 wire to properly activate your trailer's tail lights.
Note: This will not affect how the tail lights on your vehicle operate.
Because most trailers run on a 2-wire system - wherein the brake and turn signals are carried on 1 wire - the signals from your vehicle may have to be converted to be compatible with your trailer's wiring.
If your vehicle operates on a 3-wire system, which means that it has separate brake and turn signals, then those signals will need to be combined so that they run on 1 wire to properly activate your trailer's tail lights.
Note: This will not affect how the tail lights on your vehicle operate.
This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
To determine where to splice into your vehicle's tail light wiring, you will need to consult the included instructions. Use the quick-splice connectors to attach the input wires of the tail light converter to the corresponding wires from your vehicle. To get the power necessary to operate, the harness must be connected to a 12V power source. To do this, you will need the Curt powered converter wiring kit (55151 - sold separately), which contains the power wire that connects your battery.
Then locate a flat surface inside your vehicle near the tail lights and adhere the black converter box using the provided double-sided tape. Find a raw metal surface to use as a ground point and secure the white ground wire using the provided ring terminal and screw. Finally, secure the converter wires to your vehicle using the included cable ties.
It is recommended that you use a small amount of dielectric grease on the 4-pole connector to help prevent corrosion.
California residents: click here
I just finished installing the Curt trailer converter. I also used the Curt tester to verify that the harness wiring was installed correctly. All lights are operational on the tester! It was a success! I followed the instructions that were supplied and also used a VW factory wiring diagram to verify the proper wiring to the rear lights. Very honestly the use of the factory wiring diagram is a absolute necessity to get the correct wiring. I ran the wiring under the vehicle into the engine compartment to the battery. I would not recommend trying to run the hot lead through the interior and dash panel. There are not grommets in the firewall to go through and about impossible to get the trim and the under dash panels removed.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.