48" Car and Trailer End Loop 4-Pole

See what our Experts say about this Draw-Tite Trailer Wiring

• Cargo Carrier Light Kit for etrailer Cargo Carrier
  For the 24x84 etrailer Cargo Carrier for RV Bumper, # e96ZR I recommend the Cargo Carrier Light Kit, # 52014. Use 48" Car and Trailer End Loop 4-Pole, # 18044 for an extension if needed.
  view full answer...
• Are Car and Trailer End Loops # 9653P and # 18044 Each One Piece of Wire of Two Pieces
  The Car and Trailer End Loop, # 9653P, is one l2 inch long piece, just as it appears in the picture. The Car and Trailer End Loop 4-Pole, # 18044, is also one 48 inch long piece. It comes with quick splices in case one of the 4-Way connectors needs to be clipped off to splice bare wires. You can see this harness in use at about the 2 minute, 58 second mark of the video linked below.
  view full answer...
• Which Trailer Connector Will Fit T-One Vehicle Wiring Harness 118554 on a 2010 Jeep Liberty
  Once the 118554 harness is connected to your 2010 Jeep Liberty it will connect to any trailer with a flat four pole harness. If you need a flat four pole harness for your trailer we do have one available. You could use part # 18044 and cut off the vehicle side connector since you do not need it and attach the other end to the wires on the trailer. If your trailer has a different style connector, like a 5/6/7-Way connector, let us know and we can find you the other parts you would need.
  view full answer...
• Lighting Functions and Extension Cable for the Peterson Tow Light Kit
  The Magnetic Tow Lights - Red LEDs - 4-Way Flat Connectors - 20' Long Harness Item # PE26UR, provides stop, turn and taillight functions for flat towing. If you need an extension There are several options depending on the length that you need. If 48 inches would be long enough you can use the 48-inch Car and Trailer End Loop, # 18044. If 60 inches is needed use the 60-inch Car and Trailer End Loop, # 18045. If you need a custom length wire you could purchase a 4-Pole Trailer End Connector,...
  view full answer...
• Need 4-Pole Extension Wire for Cargo Carrier Light Kit # 52014
  We do offer a 4-foot extension wire equipped with 4-pole flat vehicle- and trailer-side connectors, part # 18044 from Draw-Tite. If this is longer than you need we also offer a 1-foot extension, part # 9653P, which also provides the same plug-in extension capability. No cutting or splicing is required for either extension. I recommend an application of dielectric grease on all connections when you install your light kit. We offer this (part # 11755) but it is also available locally at...
  view full answer...
• Extension Cable Available for the LED Light Kit for Railed Cargo Carriers, # 98174LED
  Installation of this LED light kit wiring, part # 98174LED, may vary slightly depending on the specific cargo carrier you have and whether the wiring harness to the LED light assemblies has to be run underneath the cargo bed versus being threaded through the carrier deck. (This will depend on how large the openings are within the deck material). I have included a video link for this product that you may find helpful. We do have both 12 inch and 48 inch 4-pole connector extensions available....
  view full answer...
• Recommendations for a 7-Way to 4-Way Coiled Extension to Flat Tow a Jeep Liberty Behind a Motor Home
  The Hopkins Heavy-Duty, Coiled Trailer Connector Adapter, # HM47075, measures 3 feet long when stretched. This will most likely not be long enough for most flat towing applications unless the 4-Way end on the vehicle has some slack that you can pull out. You could just add a 4-pole loop, # 18045, which will provide another 60 inches of length. There is also a 48 inch loop, # 18044. A longer coiled cable is not available unless you use # RM-1064-B (8 feet long) and then wire in 4-Way flats...
  view full answer...
• 4-Way Flat 24 Inch Extension Recommendation
  For a 24" 4-Way Flat extension we have the Hopkins Endurance Easy-Pull # HM47004. I like this design because there is a big loop for the connector so it's easier to disconnect the 4-Way ends instead of chancing some damaged wiring. If you'd rather use a standard 4-Way extension then you can use the part # 18044 you mentioned and just bundle some of it up with a zip tie, like what we find with the kit # DW05724-10, to take up the slack. Attached is a review video for you to check out.
  view full answer...
• How To Wire a Gooseneck Trailer from Scratch with Just Trailer Lights
  You should not need any extra fuses. Trucks like the Dodge Ram 2500 are built for towing and should have enough power on those circuits. First I would wire the lights to the trailer and worry about the 6-Way last. I would wire the lights with the standard color code. That way if you sell the trailer or have to work on the wiring in the future, it is done in the standard method. The white wire is ground and should be attached securely to the trailer frame. It is best to have direct contact...
  view full answer...
• Can T-One Vehicle Wiring Harness # 118427 Be Routed Outside and Under a 2008 Honda CR-V
  On a 2008 Honda CR-V, you could mount the T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, # 118427, on the outside of the vehicle instead of on the inside like shown in the video linked below. What you will need to do is find a grommet or exit port at the bottom of the cargo bay (you will probably have to remove the spare tire). You will need to cut a small slit in the grommet to fit the wires through. After cutting the grommet, be sure to seal it up with some silicone sealant...
  view full answer...
• Recommendation for a Trailer Side 4-Way Flat Connector on Trailer Towed by 2006 Toyota Highlander
  We have a 20-foot 4-Way trailer side connector, # A20WB. This is a wishbone harness which means that the running light signal is split at the plug and the signal is sent along to each tail light rather than using a jumper wire between the two tail lights for the signal. We also have a 35-foot harness, # A35W42B, that works the same way. I have included a link to a video showing this harness being installed for reference. Either harness will be compatible with the T-One Vehicle Wiring...
  view full answer...
• Wiring Harness for 2015 Land Rover Evoque to Connect to Lights on Bike Rack
  In order to connect the LED Light Kit # 98174LED to your 2015 Land Rover Evoque you will need a trailer wiring harness with a 4-Way flat trailer connector, such as the ZCI Circuit Protected Vehicle Wiring Harness with 4-Way Flat Trailer Connector and Installation Kit # 119250KIT. This wiring harness will install on your Evoque without requiring you to cut or splice into the factory wiring on your vehicle. The harness has zero-contact interface sensors that read the signals of the factory...
  view full answer...
• Can you Route a 4-Way Trailer Connector Under the Vehicle on a 2009 Volvo XC70
  Many vehicles will have grommets somewhere in the rear cargo area that will allow you to route wires to the underside of the vehicle. The grommets are typically found behind the rear trim panels, in the spare tire well, or under the threshold. When we installed the Curt Wiring Harness Kit, # C59496, on a 2011 Volvo XC70, we found a grommet just under the spare tire (see photo). The 2011 XC70 is the same generation as your 2009 XC70, so you should have this grommet as well. Sometimes the...
  view full answer...

Do you have a question about this Trailer Wiring?