Arrives before Christmas 
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
5" x 4-9/16". Waterproof trailer light serves 7 functions: brake, tail, turn, side marker, side reflector, rear reflector, and license plate light. GloLight lens creates a solid panel of light. Stud mount. 28 Diodes.
Features:
Specs:
This red LED light serves as a trailer tail light with stop, turn, and tail functions. The light gives your truck or trailer a distinctive look that's completely street legal. This Optronics GloLight has a unique solid light pattern when lit, so your lights stand out from the rest. Optronics GloLights are a great way to add both style and value to your truck or trailer.
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The circuit board is sealed, which means that water will not damage the diodes or circuit board.
The long-lasting, cool-burning LEDs make this light the perfect replacement for incandescent trailer lighting. LED lights are more efficient, use less power, and last much longer than incandescent lights.
The surface-mount technology used to construct these lights protects the LEDs from shock and vibration better than through-hole technology because the diodes are soldered directly to the surface of a printed circuit board instead of attached with wires that run through holes in the board. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability, and durability.
This GloLight has a 3-wire pigtail as pictured above. The pigtail hardwires into your trailer's wiring. The white wire is for the ground, the brown is for your tail lights, and the yellow is for your brake light and turn signal. This is a surface-mount light, so it will extend out from your trailer. The mounting studs are 2" apart on center.
Surface-mount lights install flat against the surface of the trailer, so a hole does not need to be cut into the trailer for the light. This type of light is installed using a flange or bracket that has mounting holes. And mounting hardware is used to secure the light to the trailer.
California residents: click here
Average Customer Rating: 4.8 out of 5 stars (1390 Customer Reviews)
5" x 4-9/16". Waterproof trailer light serves 7 functions: brake, tail, turn, side marker, side reflector, rear reflector, and license plate light. GloLight lens creates a solid panel of light. Stud mount. 28 Diodes.
I have had these installed for a year now on my 14ft utility trailer. I love these lights! They are strong, durable, bright, and look so super cool at night! Most recently, last month, I trailered 1500 miles and through the mountains in West Virginia. They held up through curves and bumps and rainstorms and even dime-sized hail! I would recommend these to anyone who needs this style of light! I wish I had brackets enough to put two on each side... just so it would look extra bada**!
These LED replacement lights are a lot brighter and easier to see day or night.
Bright led lights look really good at n ight
Perfect match for the carrier that I have. Easy to replace.
This is also great.
I gave 4 stars because I really thought they’d be brighter for backup lighting. They definitely do help in letting others know you’r intentions from behind.
We installed these clearance lights on a 16-foot tandem axle trailer a year ago that is primarily used for hauling firewood. We use it in the forest and most of the road miles are gravel. Since the lights are not housed in a recessed light fixture, we made one of steel pipe with the leading edge extended ¼ inch to deflect flying road rocks and running through brush in the forest. All the wiring under the trailer is in conduit and all the wiring is Ancor brand marine grade. Had we installed the lights as demonstrated in a picture on the etrailer.com web site, the lights would have been damaged quickly in our service conditions. The Led lights are working fine although they run a bit hotter than preferred which may lead to a shortened life. Tip: Never use copper clad aluminum automotive wire from China on trailers as aluminum is the sacrificial metal for cathodic corrosion and the wire conductors will soon disappear into powder.
This one is for the “driver” side. It has the lens on the bottom for lighting the license plate. (It does not include the license plate holder. I like this one because you just push in the wires. I recommend this light.
Upgrading our 1998 Coleman Grandview, the old incandescent just seemed too dim.
Nice light, only suggestion would be to list some wiring options, was a bit confusing going from the old Bargman to the new LED.
But I read through the Bargman page here and got squared away.
Pic is LED before anchoring compared to the stock on the right. BIG improvement.
etrailer does provide a wide range of products with different price points so the customer has a lot of choices to make the decision that is right for her\him. You also offer good online support documentation and your technical staff is also very helpful in helping the customer make the right choices.
Unfortunately, you left me with a very bad experience. I ordered a full set of lighting & wiring to redo our quad trailer from the 7-pin plug to reverse lights. A large order. I erroneously ordered 2 reverse\turn single lights, which is on me, so I expected a restocking fee (a little excessive, but that's the inventory business). I had to return the 2 wrong lights and order the correct one. I returned both lights, but etrailer said they only received one, which I was 99% sure I returned both. You had no interest or showed any flexibility considering maybe I was correct. This is a one year review you have asked me to submit and the light you claimed I did not return, still has not shown up in my garage. I liked dealing with you on numerous occasions, but I have taken my business elsewhere. That was a sad experience.
Amazing upgrade from the old metal lights even with led replacement bulb in the metal cans. One video is the halo tail lights installed, the other is chasing a ground issue with the old lights for comparison.
These lights were added to my cargo trailer that I pull behind my motorcycle. These help to make sure that people see me when I am on the road. The lights were easy to install with the grommets and pigtails that I ordered at the same time. All the products worked together well and made the project easy to do. Love these lights and will buy more if needed.
Great Light! Put two on the back of a toyhauler for backing up.
You will need the grommet and pigtail to do it right.
I had to cut two oval holes for mounting in trailer frame. Take your time with the layout and get the right sized hole saw, makes installation pretty easy.
Great Product, it's good quality and will fit perfectly for the trailer I use in my Air Conditioning, Heating & Refrigeration Business. The only problem is I ordered the wrong side. Wasn't sure if by the which one was the left or the right? I was looking at the trailer form the front when I determined it was the left one but it appears your suppose to look at the back of the trailer when you do that. Guess I will be ordering the otherside here shortly. Maybe I can get an exchange or if not then I will have a spare and hope if it does get broken again it's the other side. Etrailer has some really good quality stuff at a very good price. I got my hidden hitch from them at a Great Price. They even had a video that showed me how to install it. A couple of the local places here wanted 3 times the amount of what I paid to provide the hitch and install it for me. Will never go anywhere else for any trailer parts or accessories.
The Igor worked great. I had a heck of a time trying to order lights for the trailer - either not getting the ones I intended getting or mismatched lights. But you came through like me a champ. Thanks.
These lights are totally amazing, very bright and small footprint, just need a 3/4 drill bit and they fit like a glove, will buy more for other boat trailer upgrades.
I have a Triton trailer which had a blown out incandescent tail light.
I decided to upgrade all the lights to LED.
It took me only 30 minutes to change out all 13 lights. I used a little silicone spray and a small screwdriver and the old lights came right out of the rubber grommets and the new lights fit perfect.
They are really bright and makes a big difference, glad I did the upgrade!
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thechief
8/24/2023
Well its been another year and these lights are still going strong, still solid. I really love them!