3-7/8" x 1-1/4" Rectangle. Waterproof, 2-LED marker light mounts on your trailer fender. Amber light faces front and red light faces rear. Surface mount with bracket (sold separately). 26" Long wire with 0.156 male bullet. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Jeff: Hello everybody, this is Jeff at etrailer.com. Today we're going take a look at this Optronics Thinline LED trailer fender light with the red and amber lens. Now this is a dual face LED trailer light that will install on your trailer fender. When this is installed, the amber light will face the front of the trailer, and then the red light will face the rear of the trailer. It is a nice thinline series, has a very low profile, so that the light can fit in tight spaces. It is sonically sealed.
It is a waterproof unit, which makes it submersible. And it does use LEDs, which make great replacements for regular incandescent lights. The LEDs will last 50 times longer, they're more efficient because they'll provide brighter light with less power output. And, of course, no bulbs to replace or brittle filaments that will break. And the LEDs come with a lifetime warranty.It is in a nice durable polycarbonate housing and lens.
And as we've mentioned, it's a red and an amber lens over the white LEDs. This is compatible with 12 volt DC electrical systems. And it is a surface mount design, comes with the mounting bracket on it. And basically the way you remove it, is you can just pull on each side, and it on snap from the bracket.. just like that.
And you can see it's a two plug, that will plug right in there. The reason I took that off, I wanted to show you, it is a one wire design, has a male bullet connector on the end. Basically that'll connect to your power and the way it gets its ground is right here. So when you go to mount your mounting bracket to your trailer, and you put your screw through there, that screw will give it the ground.The length of the power wire is about 26 inches. It is a P2 rated light, few specs on this, comes with two LEDs.
The power draw at 12.8 volts is 0.048 amps. The dimension on this, I'm just going to go ahead and put it back together. Snaps together, snaps on each end. The overall length of it, including the mounting bracket is going to be right at about four and one-eight inches long. The height of it, it's going to be about one and a quarter inches tall. And the total depth of it is also about one and a quarter inches deep. Now the mounting holes, there's two of them on the back. The distance between the mounting holes, center to center, is right at three inches. And last thing I want to do is going to hook this up to some power and try to ground it, to show you how this works. So if I can get this out.So what we'll do is we'll go ahead and take our power wire, hook it up to our power, and we'll take our ground. And I'm going to, should turn this over, you can see there's where the ground is. So what we're going to do, just to show you, I'm going to try to hook our ground to there. And then when we go to plug it in, you'll be able to see, there's how your light would light up. Go ahead and turn off your overhead light. And you can see the two LEDs, over the red lens and the amber lens. Gives you a nice bright fender light. Go ahead and turn back on our overhead lights. Disconnect our power. And again, just to line the two plugs up, push it in on both sides, and it'll clip it into place. But that should do it for the review on the Optronics Thinline LED trailer fender light with the red and the amber lens.
Average Customer Rating: 4.9 out of 5 stars (667 Customer Reviews)
3-7/8" x 1-1/4" Rectangle. Waterproof, 2-LED marker light mounts on your trailer fender. Amber light faces front and red light faces rear. Surface mount with bracket (sold separately). 26" Long wire with 0.156 male bullet. P2 rated.You can always depend on etrailer.com to have a trailer part when no one else has it.
The side clearance lights on my dump trailer didn't work due to corrosion and I decided to replace the complete unit (yes, the lens and base) to the brighter LED lights. I needed the red/amber lens to match the old incandescent lens and after searching local stores and only finding the amber lens, my next search was with a reliable site that I've used many times.
etrailer.com had it (them, I replaced both sides), priced reasonably, (a little slow on shipping, but finally received them), no alterations were needed for the installation, added some heat shrink wrap around the connections and they worked perfectly.
I might add that etrailer.com is an excellent site for the "do-it-your selfers". Take advantage of the videos of any item that you are buying and the installation videos give you a little more confidence in an unfamiliar situation.
I had fender running light on my horse trailer smashed during a tire blowout. Since one of the clips on the mounting bracket was damaged so I need the complete kit. I liked the quick connect clip on the wire but since it didn’t fit through the whole in fender I had to cut it off and connect the wires without it.
Works great had no issues with installa tion.
Exact replacement. It took 15 minutes to replace both broken fixtures. Good, helpful, quick service.
Appears to be of quality material. Also, very easy to install.
Etrailer had the parts I needed and delivered on time.
Awesome products, price and service. Th anks
Excellent company with fantastic customer service. The people at etrailer sincerely care about you and your trailer.
Bought as a replacement on my ALUMA Trailer. Identical match. Works as intended.
Fast service! Thanks!
Nice lights that should work as intende d.
all good
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.