14-1/16" x 6-15/16" Rectangle. Triple LED trailer tail light serves 5 functions: brake, tail, turn, rear reflector, and incandescent backup. Durable plastic housing and lens. Recessed mount in horizontal position. 8-Wire design.
Features:
Specs:
Recessed-mount trailer lights install with a grommet, which is often sold separately. These lights extend past the trailer surface and require a hole for installation. If replacing a light, you can utilize the pre-existing hole. If installing a new light, you will need to cut a hole or use a mounting bracket (sold separately) to complete the installation.
California residents: click here
Average Customer Rating: 4.8 out of 5 stars (354 Customer Reviews)
14-1/16" x 6-15/16" Rectangle. Triple LED trailer tail light serves 5 functions: brake, tail, turn, rear reflector, and incandescent backup. Durable plastic housing and lens. Recessed mount in horizontal position. 8-Wire design.I first ordered and didn't realize they were sold individually. So I did order another one. They are a replacement for the original style lights that were not LED. They fit perfectly and are really bright. I soldered and heat shrinked all the wiring and installed butyl tape when I installed them. I did order the metal resistors so that I didn't have the hyper flash. They renew the look of an older RV. The shipping was two days and I loved that.
Hoppers - 12/29/2018Bought these light for a 1997 dynamic wrecker, perfect fit and look great. Couldn't get the lights from dynamic anymore and the lights that were on the truck when I bought it were busted up halogen.
Replaced all of the old incandescent tail and third brake lights on the rear of my old trailer. The installation was easy and only took a couple of hours. All the mounting holes lined up and it was a direct replacement. The trailer is considerably brighter now with 1/4th of the current drain. Now the trailer lights up like the Christmas Coca-Cola trucks. Trailer is much more visible at night and in the daytime making traveling much safer. I would recommend this upgrade for anyone having older trailers with the incandescent lighting.
The backup light on my RV went out. The problem was a rusted bulb socket. I would have to replace the whole tail/backup/brake assembly. SO......I decided to "go LED" and order the Bargman Triple Tail Light 84 series from etrailer. The order was processed and delivered quickly. There was a bit of work to modify the existing cutout to accept the new Bargman Triple Tail Light. But I think it was worth it. I also installed the LED Backup Light Upgrade Kit to the Triple Tail Light. These really look good on the MotorHome and I should not have to work on them again. The picture shows the old and the new installed for comparison.
We have an older camper that we wanted to update the taillights on. We bought the resistor's in case of hyperflash, but didn't need them. We LOVE the difference in the lights! We had no issues with replacing the lights, the dimensions were a perfect fit!
I give e- trailer a 5. You all were great, keeping me informed on the status of my order. My disappointment is that Bargman does not provide a seal with the light or sell them separately.
Great product works great easy to install E trailer is a pleasure to deal with
Thanks for my new tail lights love it ——
I'm very satisfied with my Bargman LED 84/85 Series trailer light. They are super bright and easy install. I've had them installed on my '94 class C RV for over a year and they are still as bright as the day I installed them. Since my current tail light assembly was same 84/85 series but incandescent and this LED Kit was an upgrade same series it was a direct fit. However since my vehicle was originally set up with incandescent bulbs front and back and now has the LED rear I had to replace vehicle's flasher relay to get rid of Hyper flash/bulb out fast blink indication. Now it flashes like it did before the replacement and I don't ever have to worry about corrosion on socket or bulb out again for a long time. Trip to Oreilly auto parts and under $4 for the upgraded flasher relay that handles both LED and incandescent lights in same circuit and hyper flash is gone. Other reviews suggested installing load resistors but there are 2 reasons why I didn't do that. Reason 1) load resistors get hot, by nature resistors resist current (hence their name) but get hot its same thing a light bulb does but we use that heat to create light by heating up filament that glows. I didn't have anything to mount the load resistors to but wood and didn't want to set my coach on fire. Reason 2) LED are low power draw on circuit and only require .5 volt to operate. I didn't want to load down my vehicles alternator unnecessarily by throwing in 6 large resistors (since I have 2 triple tail light assemblies it would require 6 resistors) that do nothing more than electrically slow down or throttle down current flow. The other thing extra resistance does in the circuit is to dim lights because there's less current flowing through the light filament it won't glow as bright because there's less current flow than before. I didn't want to spend money to dim the lights that I spent extra money to make them brighter and therefore more noticeable for the brainless, texting, snot tailgating me to not see when I put on the brakes. I hope this quick electrical 101 lesson helps others in their decision since none of the reviews mentioned upgrading the flasher relay too.
Just got around to installing the new Bargman tail lights on my 1995 Dolphin motor home. The turn signals flash very rapid and I believe I would need to install a resistor to cure this. Can you point me in the right direction ???
Heather A - 01/16/2019Once again etrailer provided perfect service!!! Their prices are great and shipping is super fast. On top of that, their customer service and technical support is second to none. I have been a long time customer and have never been disappointed. I had already purchased two of these taillights awhile back to replace the old incandescent taillights on my truck camper. I needed another to mount on a storage box, that I am mounting on the back of my truck camper, since storage box is going to cover the camper's existing taillight. These led taillights are a vast improvement over the the old ones!!! Much brighter and gives our rv a more modern, updated look.
Great Product. Easy replacement for older RVs to upgrade to LED. You will need load resisters to prevent hyperflash turn signals. No biggie. Very bright and really quick shippers here.
The load resistors that we currently have are the Aluminum version 2 pack # P230004A-2
Putco LED Light Bulb Load-Resistors - Aluminum - Qty 2
$34.74 and the Ceramic 2 pack version # P230004C-2
Putco LED Light Bulb Load-Resistors - Ceramic - Qty 2
$27.87 both of which have a provide a resistance of 6 ohms.
Rachael H - 10/29/2014No gasket to keep water out of back- up light assembly. I have had to remove the lens and dry the inside several times. Also, I had to install resistors to correct the rapid flash error as these are LEDs and previous assembly was incandescent. Overall they are nice and bright.
Works good nice and bright
This is a high quality light, and even brighter than I expected. There was a problem with some rough handling during shipping, and the folks at etrailer took very good care of me and corrected the situation about as quickly and professionally as I could imagine. Very impressive. I will be back to shop here again.
Excellent product, have not had any issues at all. They are bright lights that make it very visible to be seen. Only small issue is that my flashers blink a little faster than normal but I’m fine with that.
Great product, it came a couple of days ago. It was packaged perfectly, no damage, but the box looked like it had been used in a Samsonite Commercial on television!
PatrickA51 - 06/16/2018nice product, had to make alterations to rv which I expected. only thing could be better is if there were gaskets for the lights where they mount to rv and around the lenses to keep water out.
Fit my 1992 Fleetwood Tioga and look much more brilliant than the incandescent assembly it replaced.
The fit was very good. But the screw tabs are not as robust as the originals, both lens cracked one pretty easy when sealing the fixture against the surface. Be very careful pushing the light firmly as you tighten the screws just enough to make a seal. Also, it comes with no seal requiring use of a sealing material, I believe this is pretty standard though. They are bright and operated perfectly. Used on a 1997 coachman leprechaun 30’.
Great product. Works and looks very nice. The only problem I encountered was I had to take my vibrating saw an cut 1/4 inch off the top edge of the light opening on my motorhome in order for the unit to drop in and seat. A gasket with each light would be great. I made my own with silicone.
I ordered these lights to replace the old ones that had cracked and were leaking. They look great and were not difficult to install. They arrived quickly and were just as expected. I appreciate the rush etrailer put on my order.
Replacement for standard rear lights. LED lights are brighter and far more noticeable. These required some trimming of the motorhome body to fit, but that was minor and easy.
Nice light and looks great on my RV after replacing the old tail lights.
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Helpful Link
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.