Front Hanger for 2" Wide Slipper Springs - 3-9/16" Tall - 9/16" Bolt Hole
(28 reviews)
Price: $8.04
In Stock
Front Hanger for 2" Wide Slipper Springs - 3-9/16" Tall - 9/16" Bolt Hole
Item # 721584
Retail:$8.74
Our Price: $8.04
You Save: 8%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (28)
- Q & A (0)
- Videos (1)
- Photos
etrailer Trailer Leaf Spring Suspension - 721584
- Hangers
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Slipper Springs - 2 Inch
- 3-3/4 Inch Tall
- Single Axle
- Tandem Axle
- Triple Axle
- 9/16 Inch Diameter
- etrailer
Front hanger works with trailer suspension systems that have 2" slipper springs.
Features:
- Configured as front hanger
- Provides attachment point for leaf spring
- Hanger suspends spring from trailer frame
- Designed for trailers with 3,500-lb to 9,000-lb axles
- Fits 2" wide slipper springs
- Works with 9/16" diameter bolt (sold separately)
- Hanger measures 1/4" thick
Specs:
- Overall dimensions: 4-5/16" tall x 4" deep
- Inner width: 2-3/16"
- Height (from top of hanger to center of bolt hole): 3-9/16"
TSW 1584 Front Hanger for 2" Slipper Springs - 3-9/16" Tall - 9/16" Bolt Hole
Replaces 721584
Video of Front Hanger for 2" Wide Slipper Springs - 3-9/16" Tall - 9/16" Bolt Hole
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Video Transcript for etrailer Trailer Suspension - Leaf Spring Suspension - 721584 Review
Today we're going to take a look at the front hanger for 2 inch ride slipper springs. This is 3 and 3/4 inch tall and it uses a 9/16 diameter bolt hole. This is configured as the front hanger provides the attachment point for the front of the leaf spring which is the end that has the eye in it. This hanger will suspend the spring from the trailer frame. This part is designed for trailers with 3,500 pound to 9,000 pound axles. Again, it's designed to fit 2 inch wide slipper springs.
The hole right here is the 9/16 diameter, so it is designed to work with a 9/16th diameter bolt. Which we do sell separately on our website and the hanger itself measures 1/4 inch thick and the 3 and 3/4 inch height is measured the top to the center of the hole where the bolt goes through. So you can see if we put a ruler on that, there's your 3 and 3/4 inches tall. That should do it for the review on the front hanger for 2 inch ride slipper springs. 3 and 3/4 inches tall and a 9/16 bolt hole..
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- etrailer mistake
Customer Reviews
Front Hanger for 2" Wide Slipper Springs - 3-9/16" Tall - 9/16" Bolt Hole - 721584
Average Customer Rating: 4.8 out of 5 stars (28 Customer Reviews)
Front hanger works with trailer suspension systems that have 2" slipper springs.by: Mitchell 09/21/2023
Great deal!
by: BB.08/18/2023
Super fast service!
by: Kenny 04/11/2023
The product is steel thick enough to do the task purchased for, the real five stars comes from Ed the sales representative who helped me find what I needed and the support team behind him making the whole process of finding, ordering, purchasing and receiving easy and pleasant. Thank you.
by: Jay 02/01/2023
Great price and shipping!
by: Dustin12/06/2022
Great product
by: Thomas 07/20/2020
Strong hinge fast shipping The old one rusted out luckily my son is a welder I am hauling again
by: Jamie K.04/09/2017
This was a good replacement part.
by: Bill08/25/2019
Well made, perfect fit. I will be doing more business at etrailer!
by: Howard04/21/2022
Received exactly what I needed.
by: Steve 08/03/2021
by: Jonathan11/13/2018
Perfect fit and functioned just as good. Would def buy again!
by: Bill C09/01/2020
Size matched the dimensions listed and it does the job.
by: Erick03/23/2023
by: Sara 06/22/2023
by: Terry 08/08/2020
Very heavy duty, It was exactly as adve rtised.
by: Mike T.08/17/2016
Excellent product, excellent shipping.
by: Mark 08/15/2022
by: Leonard03/15/2019
Great service
by: Stephen 02/24/2023
by: Roger05/14/2023
by: Wyatt 11/17/2019
Heavy duty
by: Ethan 08/11/2023
by: Gregory 12/30/2021
by: Dock10/08/2021
It a good buy
by: Jim 03/25/2021
25
28
Show More Reviews
See what our Experts say about this etrailer Trailer Leaf Spring Suspension
- Top Hole Spacing and Hole Diameter of 721584 Leaf Spring HangerThe holes on top of the # 721584 Leaf Spring Hanger are 1-7/8 inches apart on center. The holes themselves are 9/16 of an inch in diameter. Please note, the holes aren't meant for bolts, the spring hangers should be plug welded to the trailer frame.
view full answer...
- Parts Needed to Raise the Height of a Trailer with 8K Dexter Nev-R-Lube AxlesSince your Nev-R-Lube axles are 3-1/2" in diameter the only solution we have for you is to install longer hangers on your axle suspension. I have attached a link to our selection of hangers that you can filter through to find the correct ones for your application. For example, our Front Hanger # 721584 is for 2" wide slipper springs. It is 3-9/16" tall with a 9/16" bolt hole.
view full answer... - Which Way Should the Opening Face on a Single Axle Trailer with Slipper SpringsThe opening or knuckle of a slipper spring will need to be facing the rear of your trailer. If the opening is facing the front of the trailer then you are going to experience excessive bouncing and a ride that would be very rough. Therefore, I do recommend changing the leaf springs around. In order to do this you are more than likely going to need new leaf spring hangers. I have attached a link with a selection of our leaf spring hangers for you. You will need to filter by width and height...
view full answer... - Height of Front Hanger for 2" Wide Slipper Springs 721584The Front Hanger for 2" Wide Slipper Springs # 721584 is 3-3/4" tall, with this measurement being taken from the center of the bolt hole to the top of the hanger. You can actually see this measurement being taken in the linked video review of this hanger.
view full answer...
- Availability of 3-3/4 Inch Tall Hanger for Trailer Suspension The only 3-3/4 inch hanger we have available is the etrailer.com Front Hanger # 721584. This front hanger is designed for 2 inch slipper springs and works with 9/16 inch diameter bolts. Also note that this 3-3/4 inch measurement is taken from the top of the hanger to the center of the bolt hole. If you are not measuring your existing hanger in this manner (and instead measuring its overall length), please let me know its bolt hole to top of hanger dimension and I will be happy to make a...
view full answer... - Availability of Front Leaf Spring Hanger for 2 inch Wide SpringsWe have a front leaf spring hanger that was designed for 2 inch wide slipper springs with the part # 721584.
view full answer...
- Recommended Replacement 2" Slipper Spring Equalizer 3-3/4" Tall I think I have a better option for your trailer with the dimensions that you provided in the Front Hanger for 2" Wide Slipper Springs part # 721584. This hanger is designed for 2" wide slipper springs, has a 9/16" center hole, and measures 3-9/16" from the center of the bolt hole to the top of the hanger where it installs on the frame. This is a bit closer to the dimension you provided but you could also still go with the Front Hanger for 2" Wide Slipper Springs part # 28-1 as well. In...
view full answer... - Dimensions of Hangers Included with Single-Axle Trailer Hanger Kit for 2" Slipper Springs APS6SEThe front hangers in kit # APS6SE are # 721584. They measure 3-3/4 inches from the top to the center of the mounting hole. The hole is 9/16 inches in diameter. The holes that are in the top are not for bolting the hanger. They are there to mount the hangers using button welds. Very few hangers are designed to be bolted on. The rear hangers in the kit are # 721585. They measure 5-1/6 inches tall from the top to the center of the 9/16 inch diameter hole. It also features the 2 holes for...
view full answer...
- What Hangers Do I need For My Heartland Cyclone 5th Wheel Toy Hauler?The CRE3000 Equalizers # MR59ZR are a great choice for an equalizer upgrade, but there is not a specific hanger set that would go with them. I can definitely help and point you in the right direction. Now, I do not have a way to know specs on your hangers based on a make and model of camper. If only it were so easy! When replacing hangers it is important that we get the height of the hanger correct. This was we can retain the factory ride height. For example part # 28-5 is a very common...
view full answer... - Replacement Spring Hangers And Suspension Components For 8,000 lb AxlesI can certainly point you in the right direction on a few of the parts you will need. Unfortunately we do not carry a 20-3/4" long equalizer, so we do not have any kits that would accommodate that hanger size and axle spacing. We do have a few hanger kits for 2" wide slipper springs like the # H202. This comes with 4-1/4" tall front hangers, 3-1/2" tall center hangers and 5-1/4" tall rear hangers. We do not have any hangers that are 7" tall. We do have the Wet equalizer bolt # TRFA71063,...
view full answer...
Do you have a question about this Trailer Leaf Spring Suspension?
Info for this part was:
Expert Research:
Mike L
Updated by:
Lindsey S
Updated by:
Wilson B
Updated by:
Mike S
Updated by:
Matthew E
Installed by:
Jeff D
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Steve H.
8/4/2022
the spring hangers I ordered were as advertised. They have done what I expected and I now have adequate clearance for the axle between axle and spring. Thanks for the prompt shipping and offering a product true to your specs.