Bulldog Square, A-Frame Jack - Drop Leg - Topwind - 28-1/2" Lift - 3,000 lbs
(461 reviews)
Price: $102.94
Bulldog Square, A-Frame Jack - Drop Leg - Topwind - 28-1/2" Lift - 3,000 lbs
Retail:$126.74
Our Price: $102.94
You Save: $23.80
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (461)
- Q & A (0)
- Photos
Bulldog Trailer Jack
- Car Hauler
- Enclosed Trailer
- Fifth Wheel Trailer
- Utility Trailer
- 2001 - 3000 lbs
- Topwind Jack
- Bolt-On
- Weld-On
- Leveling Jacks
- Tongue Jacks
- 15 Inch Lift
- With Rectangle Foot
- Steel
- Bulldog
Drop leg, square jack offers superior side-load strength and fits any standard A-frame coupler. Crank included.
Features:
- Superior side-load capacity compared with round jacks
- Outer and inner tubes overlap for additional strength when jack is fully extended
- Square design provides additional support for side loading
- Durable, long-lasting construction
- Weather-resistant coating on outer tube and zinc inner tube
- Topwind handle has smooth, ergonomic design for easy cranking
- Drop leg increases overall extension for maximum adjustability
- Mounting bracket attaches to any standard A-frame coupler
- Standard footplate base included
- ASABE compliant
Specs:
- Bracket height:
- 9-5/8" Retracted
- 38-1/8" Extended
- Total lift: 28-1/2"
- Travel: 15"
- Drop leg: 13-1/2"
- Clearance: 14-11/16" from mounting bracket to top of jack
- Tubing width: 2-1/4"
- Handle radius: 6-1/2"
- Lift capacity: 3,000 lbs
- Static capacity: 5,000 lbs
- Limited 5-year warranty
How to Determine the Lift Capacity You Need in a Jack
A trailer jack is designed to lift the tongue of your trailer so you can connect the trailer coupler to your hitch ball. To do this, you'll need a jack with a lift capacity high enough to handle your trailer's tongue weight.
Tongue weight is the amount of weight that your trailer applies to the back of your tow vehicle. Typically, your tongue weight should be 10-15% of your total trailer weight (trailer + cargo). In other words, a 10,000-lb trailer would have a tongue weight between 1,000 lbs and 1,500 lbs. For a trailer this size, you would need a jack with a lift capacity of at least 1,500 lbs.
It's okay to have a jack with a weight rating that is higher than your trailer's tongue weight. In fact, a jack with a higher lift capacity should operate more efficiently, allowing you to spend less time cranking and more time camping.
Trailer and Camper Jack Lift
Every jack offers a certain amount of lift or travel. Screw travel is the distance the jack extends when you crank it (or toggle it to "extend" on an electric model). Some jacks include a drop leg for extra adjustability. On these jacks, you'll see the maximum extension of the drop leg listed in the specs as well. Adding the screw travel and drop leg travel together will give you the total lift. The total lift listed above can help you determine how high this jack will be able to raise your trailer.
195318 Bulldog Square A-Frame Jack with Drop Leg, Topwind, 15" Travel, 3,000 lbs - TWL 195 DL-DFXQ
Item # BD195318
California residents: click here
Customer Satisfaction Score:
94% were satisfied with this product
6% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Did not fit
Customer Reviews
Bulldog Square, A-Frame Jack - Drop Leg - Topwind - 28-1/2" Lift - 3,000 lbs - BD195318
Average Customer Rating: 4.8 out of 5 stars (461 Customer Reviews)
Drop leg, square jack offers superior side-load strength and fits any standard A-frame coupler. Crank included.by: Ryan12/23/2013
Product arrived very promptly as I was upgraded to expedited status. Product was exactly as described, packaged well, and met my expectations. Product description and pictures on the website were very accurate and helped me choose the correct trailer jack for my application. etrailer.com is a pleasure to do business with.
by: Luke07/24/2020
Very sturdy construction. My light duty round jack failed in my camper and needed to be replaced. I always wanted a drip leg instead of using blocks. I had t cutout a square hole but well worth the extra effort to have a heavy duty jack with a drop leg. Thanks again to etrailer for excellent pricing and fast free shipping.
by: DennisR08/01/2023
They did a great job of getting me what I needed in a timely fashion. Arrived today and it's perfect.
by: Randy 07/25/2023
Works great and fit perfectly.
by: Chris, True Colors Industrial, L.L.C.03/06/2015
This is the 2nd Bulldog Jack I've bought from Etrailer and it's for a new 20' trailer we set up for our roofing business (I'll throw the stock A-frame jack in the trash). The drop leg makes disconnect quick and easy. We tried swivel, electric and a side mount, but this type was best for our application. And Bulldog was the best quality of the bunch. I've had nothing but great service from Etrailer and won't hesitate to purchase from them again!
by: Ted11/06/2017
Just installed today. Had to modify mounting plate for square tubing on this drop leg jack because it replaced a round tube fixed leg jack. Not too tough. We’ll see how well the jack holds up. Bulldog products are usually solid, so don’t expect any problems.
Ted
9/7/2019
It was still going strong when I sold the trailer in August 2019! New buyer was glad to see the upgrade...
by: Chris 10/03/2022
Love the drop leg design.screw works gr eat.
by: Armando 09/26/2022
Perfect fit love the drop foot!
by: Mel H.10/06/2013
Product works great. I have a 19 foot trailor with 7000 lb. axels that is heaver than average. The jack works easly loaded or empty.
Mel H.
10/27/2014
Its been a year and the jack is working as good as the first day I installed it.
by: Terry M05/29/2011
The original tongue jack on my trailer was getting stiff, was of inadequate capacity and needed to have a block placed under it to elevate the coupling enough to detach the trailer.
Replacing the original with this jack seemed like a good solution. The original jack was round so I did have to cut and file the openings in the coupler and lower tongue reinforcing plate to make it fit. Also, only one of the original three holes lined up so new holes had to be drilled.
So far the jack has worked great. The items that kept me from giving it a better rating are:
1) There is no provision for lubricating it.
2) The paint chips very easily.
by: T Thompson11/04/2014
Etrailer sent me the wrong jack at first, called them up and had the right one sent in 3 days. Love this jack, the pinned foot extension saves a ton of crank time on the handle.
by: anonymous09/21/2013
Haven't had time to test durability, but initial impression is that it sure beats the original jack that came with the trailer. The drop down foot saves a lot of time cranking and fiddling with the sand foot I used to have to attach each time I unhooked the trailer. Additionally, it is much sturdier with side deflection than a similar round jack.
by: DAVID01/14/2013
I installed this product on my camping trailer it is awesome very robust !! Exceeded my expectations as far as strength and quality ! Great product
David
7/15/2014
This is an awsome product !! The name says it all very strong and sturdy product !! I would buy again !!
by: Michael J.02/10/2017
Strong durable construction at a very reasonable price. My enclosed motorcycle trailer was well crafted with exception to the jack, it was made with poor quality steel and the workings were exposed to weather so I knew it would it be short time before I had to replace it. I always go with Bulldog products because they are of great quality and withstand the test of time.
by: Frank03/05/2018
jack came as it was describe and has more weight capacity lift. I welded on my trailer and it's way much easier then OEM 750 LBs that broke up the gears.
Lights will be put on another trailer this coming weekend.
Thank you.
Frank
by: Gene H.10/24/2012
We have a fleet of restroom trailers and we often have a need for replacement parts. These Bulldog A-Frame Jacks are the best tongue jacks that we have found. Etrailer has the best prices and extremely fast delivery. We have purchased several items from etrailer and have always been very satisfied with their products, their prices, their service and their fast delivery.
by: Craig03/08/2019
Well built unit. Handles the weight well even on sloped terrian. Only flaw is it lack's a grease fitting which started making it difficult to use due to lack of lubrication. I added one nevertheless. And now it works like new again.
by: RAY S07/28/2017
THIS IS THE SECOND UNIT I PURCHASED. THE FIRST ONE WORKED SO WELL THAT I DECIDED TO GET A SECOND FOR ANOTHER TRAILER. CRANK WORKS WELL AND REALLY LIKE THE DROP LEG FEATURE. THE ONLY DRAWBACK WAS THAT I HAD TO ADAPT THE TRAILER BECAUSE IT WAS PREVIOUSLY FITTED WITH A ROUND JACK
by: Harrell10/31/2020
We use these A-Frame Jacks as replacements on our trailers. These jacks are very strong and easy to install in the existing holes. Bulldog makes very good trailer jacks. I highly recommend these jacks.
by: Toby 01/26/2022
works great. Have it on a 4 place enclosed snowmobile trailer.
by: Jeff L.11/15/2014
Finally took time to replace my old Jack with this, I am satisfied with my purchase, etrailer.com is the place to shop! Great prices & fast delivery keep me coming back.
by: Brad 10/20/2021
it is the ONLY a-frame jack I found with an extendable leg. Unfortunately it does Not just bolt in, in place the a regular a-frame jack. I had to to do some cutting and drilling to bolt it in
by: Kyle12/20/2020
Shipped as promised, drop leg is awesome, 3000 lb jack makes you look strong even when you are not
25
460
Show More Reviews
See what our Experts say about this Bulldog Trailer Jack
- Bulldog Square A-Frame Trailer Jack is Hard to CrankYou will need to open up the jack at the top and inspect the gears inside. It is possible that you have some dirt/debris inside that is making it hard to operate the jack. If you open it up you should be able to remove the gears, clean them off, and get any grease, dirt, and debris out from the inside. Then you can put it all back together and add new grease. You will want to crank the jack up and down a few times to get everything lubricated with new grease. After that you may need to...
view full answer...
- Mounting Bolt Hole Pattern of Bulldog 195318 Drop Leg 3000lb A-frame JackThe Bulldog # BD195318 uses a bolt pattern that's a little uncommon. The back two holes are 3-5/8 apart on center and the single hole in the front is 3-1/4 apart on center from either of the rear holes. You can see this in the photo I've edited for you. If you click the provided link, you can see a product description video featuring the Bulldog BD195318 A-frame jack.
view full answer...
- Bulldog Square A-Frame Jack Measurement From Ground To BracketWhen the Bulldog Square, A-Frame Jack - Drop Leg - Topwind part # BD195318 is retracted it measures 9-1/2" from the ground to the bottom of the bracket. Please see attached video that calls out most of the measurements of the jack.
view full answer... - Stability of Bulldog Square A-Frame Jack # BD195318 When Faced with Shaking Horizontal LoadGenerally speaking, trailer jacks are intended primarily to handle vertical loads. However, the Bulldog Square A-Frame Jack # BD195318 that you referenced will typically provide better horizontal (side load) stability than a round tube jack of comparable capacity. Because they are not really intended for your atypical application there have been no tests to verify their performance in such circumstances. There will always be some degree of play between a jack's inner and outer tubes (both...
view full answer... - Replacement Bearing Kit for 3,000 Pound Bulldog Square A-Frame JackThe replacement bearing kit that you need for your Bulldog Jack # BD195318 is part # BD500251. The bearing kit is listed for a 2,000 pound jack because that is what it is more commonly used in, however it is rated for up to 3,000 pounds.
view full answer... - Replacing an A-Frame Trailer Jack with an Odd Bolt PatternI may have a solution for you, however we do not have any A-Frame trailer jacks with a mounting hole pattern like yours. All of our jacks fit the standard A-Frame bolt hole pattern which put the bolt holes between 3 inches to 3-5/8 inches apart on center. You could mount a new A-Frame jack like the Bulldog Square A-Frame Jack, # BD195318, on your trailer tongue and drill new holes
view full answer... - Bulldog Wheel Caster that Fits 2,000-3,000 lb A-Frame Trailer JacksBulldog does offer wheel casters for their jacks with the part # BD500245 but you should note that wheels like this reduce the weight capacity. This wheel has a 1,200 lb capacity which is about as high as you'd find for a wheel.
view full answer... - Installation Of Square Drop Leg A-Frame Jack On Coupler With Round HoleThe drop leg jacks that we offer have square tubing. You mentioned that the round hole you have on your coupler is 2-3/8 inches diameter. The tubing on the Bulldog Square, A-Frame Jack, part # BD195318 you referenced measures 3 inches diagonally. you would have to modify the hole in your coupler to make this jack fit. We do offer a Bulldog Round, A-Frame Jack, part # BD155032. This has a capacity of 5000 lbs and has a 2-1/4 inch outer tube diameter. I would then recommend the Bulldog...
view full answer... - Footplate and Caster Availability for Bulldog Fixed-Leg Trailer Jack # BD195321We do have a drop leg with a foot plate available for the Bulldog Fixed-Leg Trailer Jack # BD195321, but casters are not currently available for jacks with square tubes. I recommend the Bulldog 17-11/16-Inch Drop Leg With Pin # BDDF3500 to go with the trailer jack you mentioned. It has a footplate width of 7-1/2 inches and a tubing width of 1-7/8 inches and includes the pin. To avoid the cost of buying the jack and drop leg separately, you might be interested in the Bulldog Drop Leg Trailer...
view full answer... - A-Frame Trailer Jack Options with a Lift Capacity of 5,000 lbsThe Bulldog Square A-Frame Trailer Jack, # BD195318, has a lift capacity of 3,000 lbs and a static weight capacity of 5,000 lbs. If you want a jack with a 5,000 lb lift capacity, I recommend looking at the Bulldog Round A-Frame Trailer Jack, # BD1750290301. This jack has a lift capacity of 5,000 lbs, a top wind crank and a 15 inch lift like the square jack you referenced. At this time we do not have any square tube or drop leg jacks with a 5,000 lb lift capacity. This jack can be used...
view full answer... - Recommended Square A-Frame Jack With 5000 lb CapacityMy recommendation is the Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Travel - 5,000 lbs, # TJDA-5000S. This jack has the same mounting as the Bulldog Square, A-Frame Jack - Drop Leg - Topwind - 15" Lift - 3,000 lbs, # BD195318 you mentioned. The only difference is that it is a sidewind jack instead of a topwind jack. We do not have a topwind option for square A-frame jacks with 5,000 lb capacity.
view full answer... - Will the Ultra-Fab Spring-Loaded Quick Pins Fit a Bulldog Square, A-Frame Jack BD195318The Ultra-Fab Spring-Loaded Quick Pins # UF17-943031 is designed for landing gear style jacks that have legs that are up to 2-1/4 inches wide with pin holes that are 3/8 inches in diameter. Well the part # BD195318 isn't a landing gear jack but it otherwise is compatible so it would work.
view full answer... - Which Trailer Jack is Compatible with Bulldog Collar-Lok Coupler with Low-Profile Latch, # BD028499The best fit jack for the Bulldog Collar-Lok Coupler with Low-Profile Latch, # BD028499 with the same specs as the square jack is the Bulldog Round, A-Frame Jack - Topwind - 15 inch Lift - 5,000 pounds, # BD155032. Square jacks are not compatible with this coupler. The coupler accepts round jacks with 2 inch diameter tubing. The coupler with the same specs for the The Bulldog Square, A-Frame Jack - Drop Leg - Topwind, # BD195318, is the Bulldog Heavy-Duty Cast Head Coupler with Wedge...
view full answer... - Recommended A-Frame Trailer Tongue Jack for Off-Road TrailerThe best trailer tongue jack option we have for low ground clearance situations is the Ultimate Trailer Jack part # 322-RDJ-2K since you can retract the jack body all the way up in the mounting flange. It would be a perfect option and helps cut down on time spend cranking since it works as a drop leg as well. The jacks all use the same industry standard mounting flange so there won't be any issues. In regards to tire pressure, I wouldn't be able to really help with this question as from...
view full answer...
- Jack Recommendation to Provide Max Ground ClearanceA swivel jack would be your best option. A swivel jack will swivel up and out of the way totally when not in use and will give you maximum ground clearance for when you are off-road. For a bolt on jack I would go with the part # PS1400300303. I attached a review video for you to check out. For a weld on jack I would go with the # PS1401440303.
view full answer... - What Is The Mounting Bolt Pattern For The Bulldog Jack BD195318?The bolt pattern used on the Bulldog Jack BD195318 is a little different than most, but I did include a diagram showing how it measures. The outer tube will measure 2-1/4" x 2-1/4" and the inner tube is 2" x 2" . From the bottom of the mounting bracket, it will measure 9-5/8" when retracted and 38-1/8" when fully extended. From the mounting bracket to the top of the jack, it will measure 14-1/2".
view full answer...
- Does Jack Height Matter When Picking Out A-Frame Trailer JackIn general you don't have to verify the height range of an A-frame trailer jack before buying it as they all typically can go up and down more than far enough to accommodate the standard differences in trailer heights at the tongue. We do have the Ultimate Trailer Jack part # 322-RDJ-2K which would be a really great option. It lets you set the height you want the main tube of the jack to be relative to the mounting bracket so you wouldn't have to worry at all. Also the jack only needs...
view full answer... - Recommended Square Jack And Support Plate For A-Frame Trailer ApplicationThat is a custom trailer build I believe. I asked another Expert here and neither of us have seen anything like it. Since you are adding a plate to the top and bottom of your tongue, the Bulldog Jack Support Plate - A-Frame - 2.3" Square Hole # BDSPBQ50 is a great option for support if you already have a square jack. If not, I recommend the Square A-Frame Jack w/ Footplate - Drop Leg - Sidewind - 15-1/4" Travel - 5,000 lbs # TJDA-5000S or the Bulldog Square, A-Frame Jack - Drop Leg -...
view full answer...
- Does Trailer Valet TV94FR Trailer Jack Feature a Drop LegThe Trailer Valet # TV94FR trailer jack doesn't feature a drop leg. If you'd be interested in a sidewind jack with a 3K lift capacity, I'd recommend the etrailer branded # TJDA-5000S. The jack offers a total lift of 29 inches. If you'd prefer a top wind jack with a total lift of 28-1/2 inches and a 3K capacity, the Bulldog # BD195318 would be a fine choice. You can view product demonstration videos featuring the # TJDA-5000S and # BD195318 jacks by clicking the provided links.
view full answer... - A-Frame Mounted Trailer Jacks With Side Wind Handle Which Can Be Switched For a Drill AttachmentThe 2K # TV54FR and 5K # TV94FR Trailer Valet JXC Trailer Jacks are currently the only A-Frame jacks we carry which can be operated with a drill. We do not have any options like the Bulldog # BD195318 with a drop leg.
view full answer... - Are There Any American Made Trailer Tongue Jacks Available?We do indeed carry American made jacks. You will want to check out the Dutton-Lainson line. All of their jacks are made here except the Model 7201 # DL22320 and Model 3400 # DL22300. With that said, if you are specifically looking for an A-Frame jack, you will want to check out the Dutton-Lainson A-Frame Trailer Jack - Topwind - 5,000 lbs. # DL22772. This will have 14" of lift , but does not include a foot plate. If you prefer a foot plate, you will want the # DL22542, but if you wanted...
view full answer...
Do you have a question about this Trailer Jack?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Written by:
Lindsey S
Video Edited:
Jacob T
Updated by:
Adele M
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Mike S
Installed by:
Cole B
Installed by:
Shane H
Video by:
Jacob H
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Chris, L.
3/5/2016
We use our equipment and this jack has been used thoroughly for the last year and it still operates just like new. We bought another for our new towable generator. The leg makes for quick disconnect. I wont use another trailer without it.