Features:
150415 Bulldog Sidewind Jack
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
What's up everybody, Adam here with Etrailer. Today we're gonna be taking a look at the Bulldog pipe-mounted trailer jack. So this trailer jack is gonna give us a 2000-pound lift capacity. What that means is if you got 2000 pounds on here we are gonna be able to crank it up without damaging the internal gears. And it's gonna have a static capacity of 3000. So if you're just having it sitting and you have over 2000 pounds, but under 3000 it's not gonna damage it, which is nice.
What really sets this one apart is the coating on it. It has a very rust-resistant coating so you don't have to worry about this thing rusting away over time. And it does kind of look cool too. One thing that you're gonna need to get with this thing, one, with this one, we are not going to get a little piece to weld onto our trailer. So if you don't have one, you're gonna need to pick one up.
And what this one takes is a outer diameter of two inches so just make sure that it's gonna line up with that. And the pin is gonna be a 9/16 inch diameter pin but it comes with the pin. Just make sure we're gonna grab the right piece to weld on our trailer that has the same hole as our Bulldog. So as you can see here, the hole on the piece that's on our trailer is a little bit smaller than the one on our Bulldog. So it's just gonna be a little loose whenever we're cranking this thing up.
When I was cranking it I just did notice that it was a little loose but that's not really a big deal. The whole point of this is just to be able to get it to lift up. And once it sits down on the ground, it's not near as loose. One other thing you're gonna need with this is a foot plate if you want one, because it is hollow, the inner tube. So we don't want that getting full of like mud and stuff like that if you're putting your trailer on some soft ground.
So this one right here is gonna be great for it just because it has a compatibility with the two-inch diameter tube, just like that. And it comes with a pin too. This one's very popular. It's a pretty big base pad. So I would definitely recommend it. Does not come with the kit, but let's just focus on what does come with it. This one does have a grease zerk, which is nice. So typically when you see these jacks some of 'em don't have them, some of 'em do. The ones that do tend to last a little bit longer if you upkeep the grease that goes in there. So grab yourself a grease gun and some grease and do that maybe once or twice a year just to keep those gears nice and lubed up. And when it comes to the handle, this is a side-wind, so it's on the side right here. So let's go over some measurements. The radius of this handle is about six inches and we have a pretty big handle on here. And as you can see, it does rotate. So as you're cranking it up, cranking it down you don't have to worry about rotating in your hand it'll stick with you. In its fully retracted position we're gonna have about 11 and 5/8 of an inch from the center of our mounting hole to the bottom of our jack, not including the foot plate. And then when we have it completely extended out it's gonna be about 21 and 5/8 of an inch. That's gonna give us a total of 10 inches of travel. The really cool thing about this one is you can remove the foot plate. So we have a lot of different options for different plates that you can put on here. But what I like to do is grab a wheel because a lot of times you're always just a little bit off whenever you're trying to. hook up your ball mount to the coupler. Instead of just moving the truck which tends to be a little bit more time consuming and hard, you can just have a wheel on here so you can kinda roll it into position so you can grab, you can get it lined up with your ball a little bit easier with a little bit less effort. So I think that's really cool. I really like that just because you never know what situations you're in. So definitely grab a foot plate and definitely grab a wheel. Cause that really is what kind of sets this one apart. We have those options, which I really like. I do think that this is gonna look really good on the trailer and with the coating, too, it's gonna stay looking good for a long time. So I think it's gonna be a pretty good option for you. When it comes to Bulldog, I always think their stuff is high quality. So I think this really is gonna be a pretty good option for you and your trailer. Again, this was the Bulldog side-wind pipe-mounted trailer jack, and I'm Adam with Etrailer..
works very well. perfet fit
Very customer friendly company to order from.
Have really enjoyed the service. Second time I have ordered from there and would highly recommend them
good quality delivered as promised
Works as expected
It was exact product that I needed it didn’t take long to get it.
Had what I needed in stock. That is very rare nowadays. Fast shipping and quality product.
Great customer service after sending in one email. He sent me the whole package I need and It was shipped quickly. Thanks for a great job.
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.