Hub is designed for use on agricultural trailers without brakes. Fits 9,500-lb axles. Inner bearing (25590) and race, outer bearing (25877) and race, grease seal, grease cap, and threaded wheel bolts are included.
Features:
Specs:
The first number in the bolt pattern is the number of bolt holes. The second number denotes the diameter, in inches, of the circle on which the bolt holes sit.
On wheels with an even number of bolt holes, measure from the center of one bolt hole to the center of the hole directly across from it. (Example: "8 on 6-1/2" means 8 bolt holes with 6-1/2" from the center of one hole to the center of another on the opposite side.)
To determine the bolt-circle diameter on wheels with an odd number of bolt holes, measure from the center of any bolt hole to the point halfway between the two bolt holes directly across from the first. (Example: "5 on 4-1/2" means 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolt holes.)
Measuring the distance (D) from the center of one bolt hole on the wheel to the center of a bolt hole right next to it can also help to determine the bolt pattern.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody, this is Jeff at etrailer.com. Today, we're gonna take a look at this agricultural trailer hub assembly for 9,500 pound axles. Has a 6 on 6 inch bolt pattern. Now this trailer hub assembly is designed to fit on agricultural trailers that have a 6 on 6 inch bolt pattern, and it is designed for non-brake axles. It does have a built-in grease zerk fitting. If I turn this around to the very back, if you look at the bottom right there, you'll see the grease zerk fitting on it.
That allows you to hook a grease gun to that and pump grease in there so it makes it easy to lubricate your hub assembly without having to disassemble the whole assembly. Now this part does come with everything here on the table. Got it all laid out here. Comes with the hub with the bearing races already pre-installed, outer and inner. Comes with the outer bearing, which is part number 25877.
Comes with the inner bearing, which is part number 25590, goes in the back there. Comes with the grease seal that'll install in the back after the bearing's in. Comes with the grease cap that'll cover the front after the bearing's installed. And then it comes with 6 of the 9/16 x 18 wheel rug bolts. Now this is designed for use on the TRP spindle part number SP-803213-155.
Now the hub itself has a 4,910 pound load capacity. So when this is used with a hub on the other side, it'll meet the 9,500 pound axle capacity. And this is an agricultural hub. They are designed for low speed applications, so the load capacity is based on 20 miles per hour maximum speed. If you notice the grease cap here and the lug bolts, they are all a yellow zinc finish for corrosion resistance.
Now the pilot hole diameter, which is, if we measure the diameter of this right here, is 4.62 inches. And the bolt paddle we mentioned is 6 on 6 inches. And again, the lug bolt are what are designed to screw in there to attach your wheel to the hub. But that should do it for the review on the agricultural trailer hub assembly for 9,500 pound axles.
Item was used and damaged
Put my order in and it was here in less than 2 days. Everything fit exactly like it should. Extremely satisfied!!
It was a hard to find hub but fit perfectly on my tender tank trailer. Well built.
Excellent service and telephone support staff was very helpful.
Hard to find hub assembly but they managed to find one and received it within days.
Thanks
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.