To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Perfect for light-duty towing, this custom, Tesla Model 3 trailer hitch receiver features fully welded, gloss powder coated steel construction. Drawbar sold separately.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Tech Tip
No drilling required for installation , Requires temporary removal of bumper/fascia during installation , Underbody trim panel must be modified or trimmed if present , We recommend that all non-trailer loads (bike racks, cargo carriers, etc) should be supported by stabilizing straps, such as 18050, sold separately
Average Customer Rating: 4.0 out of 5 stars (10 Customer Reviews)
Perfect for light-duty towing, this custom, vehicle trailer hitch receiver features fully welded, gloss powder coated steel construction. Drawbar sold separately.Excellent product. Good instructions, but challenging with all the trim removal.
etrailer shipped the hitch in less than a day after the order was replaced and it was delivered to my house within 2 days, so kudos to the shipping department. The Curt trailer hitch itself is fine and works as promised. The etrailer price was cheaper than the retail price at the Curt website, but it appears no different than any other hitch. I had a local auto body shop install it on my Tesla Model 3, after the "pro" trailer hitch installers in my area made a big deal about how complicated Tesla vehicles were for installing hitches. They advised that they had to charge over $300 due to lengthy install time and sensors in the bumper. The body shop only charged me $200 and said it was no more difficult than any new car with sensors. Overall pleased with e-trailers customer service and prices.
Michael
4/10/2024
I had the Curt trailer hitch installed a year ago and it’s still working fine.
The hitch appears to be made well , but the installation is a bit challenging.
Watch the Eco hitch review and follow the instructions step by step and you can do it. Make sure the aluminum bumper bar is perfectly centered when you have it on the car. I would recommend installing the bumper onto the hitch on the ground and leave it a bit loose until on the car. Having a second set of hand to replace the bumper back on the car is very helpful. I left the bottom cover on the bumper.
Insufficient instructions for 2020 Model 3
Wow, that was more than I bargained for. It’s a tough install made tougher by lack of information in the video and instructions. See below. Some of these issues are mentioned in reviews of the sister hitch with a 2” receiver. Wish I had seen them first.
First, do yourself a favour and get the car 5 inches off the driveway. I built a ramp with some paving stones.
Second, there is a screw on each side right at the end of the fascia. It’s mentioned in the 2019 EcoHitch install video but not in the Curt instructions.
Third, all the etrailer.com videos and the Curt instructions are ambiguous on whether the underbody panel comes off as a separate piece or remains attached to the fascia. The Curt instructions say “to remove underbody panel locate and remove (7) fasteners…”. Should the underbody panel then come off? I couldn’t figure out how and finally took it and the fascia off together. It then became apparent that there’s no way to get the underbody panel off separately.
Fourth, the hardest part of the whole thing was putting it back together — precisely where the instructions just say “use steps 1-5 in reverse order.” There are two tabs on the inside of the fascia that hold on the underbody panel (“B” in one of the attached photos). Without the hitch, there is nothing nearby to interfere with them. With the hitch present, it is a REALLY tight fit — “B” needs to fit under “2". At first, both visually and measuring, I thought there was no way it would work. I could not find a way to do it by doing steps 1-5 in reverse order. That is, clipping the fascia into place at the trunk and then fastening the underbody panel. You need to get those two tabs under the hitch, put in (loosely) the two bolts on either side of the hitch receiver (through “A” and into “1") to hold the panel into place, and then snap the rest of the fascia into place.
There is a little bit of slop in the bolts that hold the hitch to the frame. Best your chance of getting those tabs to fit under the hitch by mounting the hitch as high as you can. You really are looking for that extra millimeter.
Lastly, the hitch is really heavy. It really hurt to feel how light everything was that I was taking off the Tesla compared to how heavy the hitch is.
Hitch is great. When I put back on the rear bumper one side didn’t fit exactly back. I think the hitch might have been a little off center which caused the issue. Plan on taking the bumper off again at some point to see if I can get it 100% tight fit.
No kidding, this is a difficult install unless you do a lot of work on cars.
The product seems well built but, as this is a difficult process, the instructions could be a lot more detailed. etrailer has a good video for the Stealth hitch install, I wish they would link it to the Curt page as the install is basically the same.
W M.
5/13/2021
1 Year in and it works great. We used the hitch to carry bikes on a 700+ mile trip to Maine and back. Lots of other misc. trips around central PA without a problem LOL, I was going to say without a hitch. I still have night sweats about the install, it was hard but Im proud of getting it done.
Fit perfectly on our Tesla Model 3. Directions from the manual weren't as clear, but etrailer had an installation video on the stealth hitch, which made it a breeze as it was quite similar. Took about an hour and 45 minutes from start to finish.
the hitch was off by a 1/2 inch and required help in the installation. now it works fine. looks a little off if you look closely
excellent product the only issue I have is wit the hardware, the y include two different size, standard and metric, should be only one type either standard or metric not mix.
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Marvin
8/11/2024
We used this trailer hitch for a two bicycle carrier on my Tesla Model 3, and it works great. Very sturdy and inconspicuous.