To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
This fully welded, corrosion-resistant vehicle trailer hitch receiver is perfect for your light-duty towing needs. Draw-Tite's Tested Tough guarantee ensures that this hitch exceeds industry standards. Drawbar sold separately.
Features:
Specs:
Draw-Tite's Tested Tough program provides testing standards far superior to those outlined by the Society of Automotive Engineers (SAE), the go-to source for engineering professionals.
Each Draw-Tite trailer hitch receiver undergoes extensive fatigue testing and static testing with the ball mount that is either supplied or recommended for use with that particular hitch, thus ensuring results that are applicable to real life use. Fatigue testing is also conducted on hitches rated for use with weight-distribution systems.
In addition, Draw-Tite performs static testing on a simulated automobile, as opposed to the rigid fixture used for SAE testing, resulting in a more true-to-life scenario.
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
California residents: click here
Works great for towing a small rented trailer ~1000 lbs. It does fit on the Honda Civic Hatch Sport Touring with heavy modifications required, see pictures. These are all just suggestions, follow them at your own risk.
Since my car has a center exhaust, it had to be heated and bent slightly outwards to fit this hitch receiver. This makes it difficult to insert the hitch pin without bending the exhaust significantly. Once everything is installed there is a slight vibration while driving and changing accessories or removing the hitch receiver becomes difficult.
The center rear jack point on the car also had to be cut off which can be accomplished with a dremel or angle grinder. Don't lift the car from this point after cutting it. Once installed, the hitch receiver is barely visible and looks good. No visible rust after one year installed. I've found that with a 5" rise, the hitch ball sits roughly level with a UHaul trailer.
Hitch still attached to car :-) ! (2023 Honda Civic Hatchback)
I rarely use it, and only then for my Saris two bike carrier.
does the job. good instructions
Seems ok but I am concerned about the welding job as the welding wasn't done on both sides of each part. But I'm no welding expert so may be fine. Another dislike was the paint was flaking off on the edges. But all in all seems sturdy. Took me about 3 hours to completely install it. Was pretty easy. I didn't cut out the metal pieces on each side like the video tells you to do, Instead, I just hammered them down.
Steven
12/19/2023
After about a year the hitch has been working well for me. My bikes are kinda heavy and with the bike rack weight I am getting close to the Max of 200 pounds downward force. But all in all works well. Try not to drive fast when using it as again I have alot of weight on it. But hasnt failed me yet.
This fits well on my 2024 Civic Si and I would highly recommend it! One thing I will say, though, is to expect your hitch to be damaged in shipping. I have seen many reviews on this website showing damaged boxes in shipping. I’ve ordered two of these from this site and both came with holes in the box and paint damage/chipping to both hitches. This is not the end of the world for me, and because this is a review of the hitch and not the company’s ability to ship things, I give it 5-stars.
I've bought about 6 hitches from etrailer and have been pleased with all of them. I did have to grind a little bit off this hitch to fit over some contours in the car body but that only took a couple of minutes. The job was completed within the 2 hours advertised.
Keith
7/3/2020
Its still working just great. And no rust has appeared yet.
I used this on my 2025 civic hatchback very easy to do with very little cutting on the bumper. It’s not even noticeable. It arrived very quickly also. I would definitely buy again.
Great fit and installation directions.
Overall, this hitch receiver does the job. Does it do it well? Not really. The receiver is slightly larger than 1 1/4", so my bike rack wobbles as I drive. I haven't figured out how to remedy this. Not only is the receiver too large for a 1 1/4" hitch, it's also not level. My bike rack careens off to the driver's side. Please do better.
Brooke M.
2/24/2025
Hey Jens! I wanted to ask and see if you could some pictures that show how the hitch isn't level and of how the rack leans once installed. I know sometimes when you wiggle the bike rack while tightening the anti-rattle device on it ( if it has one) it can really help to take up extra space and get a tight grip. Let me know if that helps!
Arrived in 2 days. Had it installed and it looks excellent. Fit my 2024 Honda Civic perfectly and it's a clean look.
Customer service is outstanding! They are very proactive and reach out to you throughout ordering/shipping. Hitch is high quality and used YouTube video to confirm instructions. Installation was easy and only took a couple hours. I wish all companies were this way. Thank you and very happy with my purchase.
Dave
6/26/2024
Still a great product!
Installed on a 2017 Civic EXT in a couple of hours. Fits perfectly and looks great with the cross tube hidden under the bumper cover. Instructions were well written. Hardest part for me was removing the bumper cover / being afraid I would break a clip or scratch the paint. Just take your time on this part of the process!
I regularly tow a small kayak trailer with all-up weight of 500 lbs and tongue weight about 60 lbs. The hitch handles it without issue.
Not installed yet. Trailer taillight harness also not used due to requirement to splice wiring. Will order updated wiring which is plug-in except on battery. Main reason is new car makes installing more difficult. Etrailer produces used in the past have been excellent.
Perfection!
Sales, delivery, product the best I could have received.
Now, I'll safely trailer my bikes anywhere.
Excellent product. I saw the other Civic Si with this hitch on it and knew it could be a cleaner install. All it takes is a quick trip to the muffle shop to have them mock it up and shorten the 90s coming off your mufflers.
All advice is given without any warranty or acceptance of liability. If you follow these instructions, it's at your own risk.
Cut the 90s off leaving about 1/2" of straight pipe coming out of the mufflers. Then take the 90s and shorten them until they avoid the hitch. Then reweld the shortened 90s back on (I used a local muffler shop) and add a 2.25" pipe (bumped out) to slip over the existing pipes and reweld everything. Consider finishing with black hi-temp spray paint.
Couple other tips that were not in the instructions... you will greatly benefit from having access to an angle grinder to notch the bumper. There were a couple steps that were not called out in the instructions, namely:
1. Directly behind the flanges connecting the bar to the frame you need to make a small notch for the flange to fit flush.
2. There are two tabs that need to be bent down that hold the stock bumper up. You can't properly bolt the hitch up with these sticking out.
Great hitch. Pretty easy install. Website stated 10/10 difficulty...was a little apprehensive because of that...but went ahead. Glad I did! Took about 2 hours...with two phone calls from my daughters along the way. Used a dremmel tool to cut out the bumper for clearance per the instructions. Interestingly, I used the dremmel tool to cut out the slot for the receiver...it kinda melts the bumper...just rub it off with your finger and it is a smooth clean cut. First picture is with the bumper and fascia off...second is the back of my new 2019 hatchback with the bumper still on...3rd is the finished installation...looks great! Going to put a Black on Black Honda hitch cover on...$4.95 on eBay! Price on the hitch was great too!
Hitch fits well, instructions were good overall. I am excited to use it to transport by bikes.
This hitch was advertised to fit the new (11th gen) 2022 Civic sedan and hatchback, although I was somewhat concerned because all installation photos/videos and the enclosed instructions referenced the previous 10th generation. Needless to say, the installation went PERFECTLY, and aside from a few differences in clip/fastener locations for the bumper cover assembly, the instructions can be followed to the letter for this new generation. Most importantly, the cuts to the bumper beam and fascia cover are still spot on and lead to seamless installation. I am thrilled with the look of the finished product on my 2022 Civic hatchback!
I installed this Draw-Tite hitch on a new 2019 Civic hatchback. The installation took about two hours and went pretty smoothly. The video on etrailer.com was very helpful to understand the installation steps, but I made a few deviations that may be helpful to others.
1. I removed the tail light housings completely as it makes seeing the clips easier when reinstalling the bumper cover. After removing the two phillips screws, the tail lights are secured by two clips that release by pulling the housing outward. I then just unscrewed each bulb socket, released the one cable stay, and set them aside.
2. I used an air powered cut-off tool to trim the bumper ends for clearance - it worked fast and made a clean cut.
3. When reinstalling the bumper with the hitch, there is a hooked sheetmetal tab that extends from the bumper mount point on the car frame and rests in a notch on the bumper's mounting flange. With the added offset from the hitch, that tab can be difficult to latch and may get in the way. After struggling a bit to get both sides latched, I ended up just bending one tab down a little to move it out of the way. I'm guessing it's just an assembly aid for the factory.
4. The etrailer.com installation video has Shane cutting the fascia twice as wide as what the instruction sheet says. The video describes cutting an opening 5 inches wide (2 1/2 inches on each side of center), where the instruction sheet diagram shows a cut 2 1/2 inches wide (1 1/4 inches on each side of center). The narrower cut matches the hitch width and looks really clean. After using a step drill for the rounded corners of the cut , I then used a sharp razor blade to trim the plastic fascia. The bumper cover was out in the sun for some time which probably softened it a bit, but the razor cut it easily and made for a very clean cut.
Very happy with the results!
I hesitated to purchase this hitch because of the installation. I’m glad I made the purchase.
Much easier installation than anticipated.
1.5 hours total...including clean up, searching for a dropped screw and measuring 3 times to make sure my cut was accurate.
I placed a moving blanket under the rear of the car, no jack needed.
You need to use some force to get things going but I was careful.
I watched the 2019 hatchback installation video a few times...mine is the sedan and things were exactly the same.
Good luck with your installation.
Hitch works perfectly. This is my 5th E-trailer hitch I have owned and installed now.
I would buy again for the future (when necessary) and would recommend.
I installed this on a 2018 Honda Civic Si with center mount exhaust. To do this, I had to cut off the mass production exhaust and rebuild it (see photos).
Looks great and works perfectly.
Hi im happy i purchase this product took me 2 to install the product from installing and cutting underneath dont rush to cut the space so you wont cut it so wide you have to measure the center, the rear bumper to look neat i use flexible rubber hose around the cut at seen in the picture. I love this product because you can hide the long tube underneath the bumper to look nice and clean. Just follow the instruction and everything just fine. I surely recommend this product to any sedan car who wants there hitch rack looks great. Thank you
I love my hitch! I have a 2018 Honda civic Si 6 speed manual transmission. I tow a small motorcycle trailer A few times a year but mostly have my bicycle carrier on it, almost daily!
It does a good job. I have had zero problems with it. Highly recommend it to all my friends
It mounted like the instructions explained and has been doing its job its supposed to. Definitely will buy again from this company for future vehicles.
Do you have a question about this Trailer Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Victoria H.
2/13/2025
Thanks for sharing your valuable insight, John! I appreciate that you included photos as well!