See what our Experts say about this Tow Ready Trailer Hitch Ball

• 2-5/16" Hitch Ball With A 3" Long Shank
  If you're saying that you need a 2-5/16" hitch ball with a 3" long shank then we do offer the Buyer Products # 337RB102516. The shank is 1-1/4" in diameter and has a 20,000lb towing capacity.
  view full answer...
• Hitch Ball and Shank Recommendations for a Equalizer WD System
  You would need to measure the shank of your current hitch ball to see if it would be compatible. You will need to measure the width of the threaded portion of the ball as well as the length of that same portion. For a hitch ball that fits the required dimension you would want part # 63018 for a 2 inch ball or part # 63019 for a 2-5/16 inch ball. For a shank you could use the part # 17120 as it would be compatible and would work well.
  view full answer...
• Recommended Hitch Ball For Use with Equalizer Weight Distribution Systems
  Since Equalizer specifically recommends a hitch ball at or less than 2-3/8 inches in length with a 1-1/4 inch diameter shank you would want to use the part # 63018 for a 2 inch ball or part # 63019 for a 2-5/16 inch hitch ball with the part # EQ37100ET. If you were not going to use the one that came with it.
  view full answer...
• Replacement Ball for a Draw-Tite Pintle Hitch Combination Trailer Hitch
  The correct replacement ball for a Curt Pintle Hook Combo, # C48200, with a 2-5/16 inch ball is the Pintle Hitch Ball, # C48830. The Tow Ready Ball, # 63019, fits pintle hitch # TR63042. If you were towing a trailer with a lunette ring, you would not remove the ball. The ball is what retains the ring and the top part of the pintle hitch keeps it from jumping up and off of the ball.
  view full answer...
• Replacement 2-5/16 Inch Trailer Ball for Equal-i-zer Weight Distribution Hitch
  The Tow Ready Pintle Hitch Ball you referenced, part # 63019 would work just fine with your Equal-i-zer weight distribution hitch. As you said, those systems use a ball with a 1-1/4 inch diameter with a shank no longer than 2-3/8 inches. You'll want to make sure that the fully loaded and ready to tow tongue weight of your TT (plus the weight of anything stowed behind the rear axle of the tow vehicle) doesn't exceed the capacity of the Equal-i-zer system you're using.
  view full answer...
• How to Remove Ball from Pintle Hitch
  It will depend on which pintle hitch you have. Some like the Curt # C45908 have removable trailer balls, some do not. If the trailer ball has a nut on the underside of the pintle, the ball should be removable. It it does not, the ball isn't removable. If the ball on your pintle is held on with a nut and lock washer, once you remove the nut you should be able to rap the end of the shank a few times with a dead blow hammer at which time the ball should come loose.
  view full answer...
• 2-5/16 Inch Ball for a Curt Pintle Hitch
  The ball part of hitch ball # 19286 is a little more than 3 inches tall so it would not work for you. You need ball # 63052. Provided the shank diameter you need is 1-1/8 inches, it does have the 2-3/4 inch height for the ball portion. Or for a 1-1/4 inch diameter shank use ball # 63019.
  view full answer...
• CURT Trailer Hitch Pin Capacity and Pintle Hitch Ball Recommendation
  The CURT Hitch Pin, # C21500, does not have an official capacity because it far exceeds the ability of most anything it can be placed in. A believe I have found the perfect ball for you. Take a look at Pintle Hitch Ball, # 63019. It has a 2-5/16 inch diameter with a 1-1/4 inch threaded shank. It has a capacity of 14,000 pounds. This is the highest capacity ball with a 1-1/4 inch shank. It may be too close for comfort if you are towing exactly 14,000 pounds. If at all possible, reduce...
  view full answer...

Do you have a question about this Trailer Hitch Ball?