1-7/8" Hitch Ball - 3/4" Diameter x 2-3/8" Long Shank - Chrome - 2,000 lbs

See what our Experts say about this Draw-Tite Trailer Hitch Ball

• Trailer Hitch and Wiring Recommendation for 2014 Chevy Impala
  We have hitches that fit your 2014 Chevy Impala like the Draw Tite Class II hitch part # 36543 which is what I recommend. It installs easily and also gives you a mostly hidden solution. This is a bolt on hitch that does not require any welding. For trailer wiring our most reliable option is the Tekonsha # 118590 which I recommend for you. For a ball mount the # 36061 is the required part number and then for a ball # 19257.
  view full answer...
• Best Trailer Hitch Receiver for a 1999 Buick LeSabre
  We currently only have one trailer hitch receiver for your 1999 Buick LeSabre which is the Draw-Tite Trailer Hitch Receiver part # 36216. This option will give you a Class II hitch with a 1-1/4" receiver tube opening. I have attached an installation video on a similar 1997 Buick LeSabre for you as well. If you can tell me what you will be using the hitch for I would be glad to offer some additional recommendations for you as well.
  view full answer...
• Trailer Hitch and Wiring for a 2015 Subaru Outback with Rear Bumper Underguard Trim
  Yes, Curt trailer hitch # C12136 will fit all models of the 2015 Subaru Outback including yours. I have included a link to a video showing an example installation for you. If you plan on doing some towing you can use ball mount # C45521. For a 1-7/8 inch ball use # 19257 and for a 2 inch use # 19258. For trailer wiring you can use # 118467 to add a 4-Way flat connector to the rear of the vehicle. If you are using the hitch for accessories and not to tow then Curt also says you have to...
  view full answer...
• Trailer Hitch and Wiring Harness Recommendation for Towing Dirt Bike w/ 2001 Volvo V70 Station Wagon
  Since you'll be using the hitch for towing purposes, I'd recommend you go with the Draw-Tite # 36297. The hitch does indeed include all necessary installation hardware. In addition to the hitch, you will need a ball mount like # 36051. You'll also need a trailer wiring harness like part # C59496 and a trailer ball like part # 19257 for a 1-7/8 inch ball or # 19258 for a 2 inch size. The coupler on your trailer will have the correct ball size stamped into the metal of its coupler. I'm...
  view full answer...
• Recommended Trailer Hitch Receiver For 2005 Chevrolet Impala
  I have another option for you but the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13315 you were looking at is only confirmed to fit select Mazda CX-5's. There is not a class III hitch available for your 2005 Chevrolet Impala so I recommend the Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" # 36407. This hitch has a 300lb tongue weight rating and 3500lb trailer weight rating so it will be perfect for carrying a bike rack, cargo carrier, or even a ball...
  view full answer...
• Trailer Hitch and Wiring for a 2017 Volkswagen Golf Alltrack
  Trailer hitch # 24949 is a fit for the 2017 Volkswagen Golf Alltrack. It also is listed for all models of the 2017 Golf Sportwagen. I have included a link to the installation instructions for you. If you plan on doing some towing the recommended ball mount is # 3590. For a 1-7/8 inch ball use # 19257 and for a 2 inch ball use # 19258. And for trailer wiring you can use # 118730 to add a 4-Way flat to the rear of the vehicle. If you want to use the hitch for an accessory such as a bike...
  view full answer...
• Trailer Hitch and Wiring for a 2014 Toyota Prius V
  I have to tell you first that Toyota states not to install a trailer hitch on the 2014 Toyota Prius V. It is stated in the owner's manual. If you choose to install a hitch and tow with the vehicle then trailer hitch # 24847 fits your Prius. The correct ball mount to use is # 3593. For a 1-7/8 inch ball use # 19257 and for a 2 inch use # 19258. And for trailer wiring use # 118610. I have included links to videos showing example installations of the hitch and wiring for you.
  view full answer...
• Choosing a Ball Mount with Enough Rise to Tow a Trailer Level with a 2014 Honda Civic Sedan
  Yes, that makes perfect sense. What you are talking about is rise and drop. If the vehicle hitch is lower than the trailer coupler with the trailer level then you will need a ball mount with a rise to compensate. If the vehicle was higher the ball mount would need to have a drop. To figure out the rise you will need you can use the trailer jack to make the trailer level then measure from the ground to the bottom of the coupler. Then you would compare that to the hitch measurement taken...
  view full answer...
• Wiring Harness for 2013 Mazda CX-5 Pulling Trailer With LED Lights
  There are two wiring harnesses for your 2013 Mazda CX-5 and the correct one will actually depend on if your Mazda has LED taillights as opposed to the trailer you are pulling. So you can use the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56011 on your '13 Mazda CX-5 so long as the vehicle does not have LED taillights. If your Mazda does have LED taillights you will need the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118563, and...
  view full answer...
• What is the Recommended Ball Mount for Draw-Tite Trailer Hitch, # 36297
  The Draw-Tite trailer hitch, # 36297, that you have referenced is a Class II trailer hitch. with a Class II trailer hitch, you will need to use the manufacturer recommended ball mount. According to the installation details linked below, the required ball mount is # 36061, and it should be used in the rise position only. It has a 3-1/8 inch rise and measures 9-3/4 inches from the center of the hitch pin hole to the center of the ball hole. This ball mount is rated at 3,500 pound gross...
  view full answer...
  
• Trailer Hitch and Wiring for a 2016 Honda Civic Coupe LX
  The trailer hitch for the 2016 Honda Civic Coupe is Curt hitch # C92UR. It is rated for 2,000 pounds gross trailer weight and 200 pounds tongue weight so it can handle the trailer and bike. The recommended ball mount is # 3593 and you can use 1-7/8 inch ball # 19257 or 2 inch ball # 19258. And for a trailer wiring harness use # C56324. It plugs in line with the vehicle tail light wiring. I have linked instructions for the wiring and hitch for you. When you install an aftermarket part...
  view full answer...
• Trailer Hitch and Wiring for a 1996 Buick Roadmaster
  We have a class II hitch that will fit your 96 Buick Roadmaster. The Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" Item # C12009. We haven't had the chance to install this hitch on a vehicle, but it is rated for a 50 minute install and has some drilling required. You can see the installation steps in the instructions I have linked. This Class II hitch is the only option for your vehicle so provided that its 3,500 pound capacity as well as the car's capacity are high enough...
  view full answer...
  
• Trailer Hitch Receiver to Fit 2016 Chevrolet Impala Limited
  We have two trailer hitch receivers to fit your 2016 Chevrolet Impala Limited and they're both 1-1/4 inch Class II receivers. The Draw-Tite # 36407 and the Curt # C12252. They both have a maximum gross trailer weight of 3,000 pounds and a maximum tongue weight of 300 pounds. The Curt does require the use of a stabilization strap, part # 18050, in order to be in compliance with their warranty whenever carrying non-trailer loads. For this reason I suggest the Draw-Tite. If you're going...
  view full answer...
• Do Any Modifications Need to be Made to a 2007 Volvo S-80 to Install Curt Trailer Hitch # 12287
  To install the Curt Trailer Hitch, # 12287, on your 2007 Volvo S-80, you will need to temporarily lower the exhaust in order to attach the hitch to the vehicle frame. After the hitch is in place the exhaust will be put back in its original position. A heat shield will also have to be temporarily bent, also to allow the hitch to raise into position. It will be bent back when complete. Some fascia trim will be removed but it, too, will also be replaced after installation. I have included...
  view full answer...
• Trailer Hitch and Wiring for a 2014 Chevy Cruze Diesel Towing a Seadoo Spark PWC
  For your 2014 Chevy Cruze diesel I recommend Draw-Tite trailer hitch # 24882. This is a Class I hitch with a 1-1/4 inch receiver. I have linked a video showing an example installation for you. You can also see how much of the hitch is visible in the video. For a ball mount use # 3593. It comes with a pin and clip. For a 1-7/8 inch ball use # 19257. Or if the trailer requires a 2 inch ball use # 19258. And for trailer wiring you can use # 118508 to add a 4-Way flat connector to the rear...
  view full answer...
• Trailer Hitch and Wiring for a 2000 Mercedes E320 Sedan
  The only trailer hitch for the 2000 Mercedes E-Series is Curt hitch # C11744. The recommended ball mount for this hitch is # C45521. And for a 1-7/8 inch ball use # 19257 and for a 2 inch use # 19258. For a wiring harness you can use # C59496 to add a 4-Way flat connector to the rear of the vehicle.
  view full answer...
• Recommended Trailer Hitch, Ball Mount, Trailer Ball and Trailer Wiring Harness for 2015 Toyota RAV4
  There are both Class II and III hitches available for a 2015 RAV4, but I'd recommend going with a Class III, because there is a much better selection of hitch mounted accessories available for the more common 2 inch Class III receiver. The Class III version, # C13149 is very similar in price, and would provide much more flexibility. I've linked an install video for you. Since you'll be towing, you'll also need a wiring harness like # 118578. I've lilnked to an install video that will help...
  view full answer...
• Recommended Ball Mount for Class II Hitch Installed on 2003 Chevy Venture
  The recommended ball mount for your 2003 Chevy Venture for the Reese Class II hitch you have installed on your 2003 Chevy Venture is the Draw Tite part # 36061. Then for hitch balls you'd want the part # 19258 for a 2 inch ball or part # 19257 for a 1-7/8 inch ball.
  view full answer...
• Trailer Hitch Recommendation for a 2004 Volvo XC70
  All of the available trailer hitches for a 2004 Volvo XC70 are class II hitches with a gross trailer weight capacity of 3,500 pounds and a tongue weight capacity of 300 pounds. If the combined weight of your horse and trailer (loaded and ready to tow) is less than these limits you could certainly tow with your Volvo. If that ends up being the case, I recommend the Draw-Tite Class III Trailer Hitch # 36297 because it will well for both towing a bike racks. The Curt trailer hitch for your...
  view full answer...
• Recommended Trailer Hitch And Trailer Wiring For 2017 Chevrolet Impala Premier
  I recommend the Draw-Tite # 36538 trailer hitch for two reasons. First, the Curt hitch # C12115 requires trimming of the underbody trim panel. And second, the Curt hitch requires the use of a stabilizing strap like part # 18050 when using the hitch for any non-trailer items like bike racks and cargo carriers. Both trailer hitches are visible, but the Curt hitch may be a little less visible because of the underbody trimming. The # 36538 hitch requires no drilling for installation. This...
  view full answer...
• Recommended Trailer Hitch Receiver and Vehicle Wiring Harness For 2014 Nissan Altima
  I would be happy to recommend a trailer hitch receiver and vehicle wiring harness for your 2014 Nissan Altima. Starting with the trailer hitch receiver I recommend the Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24796 which has a 200lb tongue weight rating and 2000lb trailer weight rating. Moving on to the wiring I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118470 which will plug in to your factory wiring and will...
  view full answer...
• Recommended Ball Mount Compatible With 1998 Cadillac DeVille
  Based on the confirmed fit trailer hitch receivers we have for your 1998 Cadillac DeVille, I assume you have a 1-1/4 inch receiver opening. Because of how far back this sits from the bumper, I recommend the Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 11-3/4" Long - 3,500 lbs # 36063. With this ball mount you can use # 19258 for a 2 inch hitch ball or # 19257 for a 1-7/8 inch ball.
  view full answer...
• How Hard is it to Install a Trailer Hitch on a 2013 Cadillac XTS
  The installation difficulty for Draw-Tite trailer hitch # 36538 for a 2013 Cadillac XTS is listed as a 5 out of 10. The scale is based on estimated time to install the hitch with each tick on the scale representing 10 minutes. So at a 5 it would take a professional approximately 50 minutes to perform the installation. We usually estimate a novice will take twice as long so that would be 1 hour and 40 minutes. If you plan on doing some towing the recommended ball mount is # 36061 and it...
  view full answer...
• Trailer Hitch and Wiring for a 1999 Ford Escort ZX2
  The only trailer hitch available for the 1999 Ford Escort ZX2 is a Class I hitch # C11105. The recommended ball mount is # C45520. For a 1-7/8 inch ball use # 19257 and for a 2 inch use # 19258. For trailer wiring use # 118344 to add a 4-Way flat connector to the rear of the vehicle. If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited...
  view full answer...

Do you have a question about this Trailer Hitch Ball?