See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Ball Mount for 2-1/2-Inch Hitch That Gives 8-Inches of Drop
  The Convert-A-Ball 2-1/2-Inch Cushioned Ball Mount # AMSCV-6 provides height drop of 6-inches but since they do not offer one like it with 8-inches of drop you can instead check out the items on the linked page which provide 8-inches of drop. These include both fixed ball mounts like 12K Draw-Tite # 45291 and 20K Curt # C45460 and adjustable ball mounts like Bullet Proof # ED258.
  view full answer...
• 2-1/2 inch Hitch Adjustable Ball Mount Recommendation for a Ford Hitch
  The issue with the Ford factory 2-1/2 inch receiver is that the radius of the rounded corners is different than the radius of the rounded corners on the Titan shank you mentioned. It may not be the solution you had in mind, but the only ball mounts we have that will fit a 2-1/2 inch hitch and give you the amount of drop you need would be an adjustable ball mount like the part # DTSTBM6825.
  view full answer...
• 10to 12 Extended Ball Mount For Class-5 Hitch With 2 Receiver?
  In your question you state that you have a Class-5 hitch, and they come with a 2-1/2” receiver opening. You also state that you have a 2” receiver. I will offer a ball mount solution for either size receiver. For a 2” receiver you can use the 13-1/4” long Brophy # BM20 with 2” drop, or the 14-1/4” long Curt # D-28 with 6” drop. For a 2-1/2” receiver you can use the 12-1/4” long Convert-A-Ball # AMSCV-6 with 6” drop, or the 10-1/2” long Draw-Tite # 45291 with a 7-3/4” drop, or the 13-1/4”...
  view full answer...
• Can a Ball Mount for a 2-1/2 Inch Class V Trailer Hitch be Used in the Rise Position
  Depending on the ball mount, you can use it in the rise or drop position. Some ball mounts, like # 45291, can only be used in the drop position. The Reese Titan Ball Mount, # RP45323, that comes in the etrailer Ball Mount Kit, # EBMK25518, can be used in the rise or drop position. It will provide 3-1/2 inches of rise or 5 inches of drop. I have included a link to our FAQ article on choosing the right ball mount for you.
  view full answer...
• Is Ball Mount Adapter # A81008 Needed to Install Rockstar Mudflaps While Using Brophy Reducer # HR26
  To use the Rockstar Mudflaps on the # HR26 reducer you will need to use the Ball Mount Adapter # A81008 if you do not have a 2 inch ball mount installed as well. If you have a ball mount in the adapter then the mud flaps can be installed on it. If you're using the reducer as a location to install the mud flaps then the # A81008 is needed. Another option instead of the # HR26 is to install a 2-1/2 inch ball mount with a long shank like # 45291.
  view full answer...
• Ball Mount to Fit a 2-1/2 Inch Trailer Hitch Receiver with 6 Inches of Drop
  We have a couple ball mounts that are going to be very close to what you're looking for. The Curt Ball Mount # 45291 is a fixed ball mount that has 7-3/4 inches of drop and 10-1/2 inches from the pin hole to the center of the ball hole. It also has a maximum tongue weight of 1,200 pounds. However, it is steel and not aluminum. You also need a hitch ball # C40030. Another option is the Fastway Flash E Series HD Adjustable 2-Ball Mount # FA42-00-2625 that's rated up to 1,800 pounds tongue...
  view full answer...
• Ball Mount with 4 to 6 Inch Drop for a 2-1/2 Inch Trailer Hitch Receiver
  B&W ball mount # BWBMHD30214 has a 6 inch drop and will fit the 2-1/2 inch Ford receivers. It is rated for 16,000 pounds gross trailer weight and 1,600 pounds tongue weight. I have included a link to a video review for you.
  view full answer...
• Ball Mount with 8-Inches of Drop for Use in 2-1/2-Inch Hitch
  We can offer you a choice of fixed and adjustable type ball mounts in your required 2-1/2-inch size that give you the 8-inches of drop. You can see all on the linked page. For a fixed ball mount you can use Draw-Tite # 45291. Be sure to choose a hitch ball that has the correct 1-1/4-inch diameter shank to fit this, such as 2-5/16-inch ball # C40030. If you prefer a multi-ball adjustable mount you might consider the Weigh Safe # WS8-25.
  view full answer...
• 8 inch Drop Ball Mount Recommendation for 2018 RAM 2500 with 2-1/2 inch Hitch
  We have the Draw Tite ball mount part # 45291 that fits a 2-1/2 inch hitch like what you have and has an 8 inch drop which is the closest fixed ball mount we have to 10 inches of drop. This has a capacity of 12,000 lbs too.
  view full answer...
• Recommend Ball Mount To Clear Rear Bumper of 2008 Toyota Sienna
  We do have a ball mount that should work well for your towing setup, but, the item you referenced, Forged Ball Mount, part # 40332, will not provide the 7 inches of clearance from the pin hole to the edge of the bumper. The item you selected, Titan Ball Mount, part # 45291, cannot be used in the rise position, so it will not work for your towing setup either. A good solution to provide rise to keep your trailer fairly level when towing and to clear your rear bumper would be the Curt...
  view full answer...