Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs

See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Will Curt Hitch and Tekonsha Wiring Fit 2012 Kia Optima
  Yes, both the Curt # C11025 and Tekonsha # 118453 will fit your 2012 Kia Optima. If you're planning on towing you will also need a ball mount like # 36065 along with # 19256 for a 1-7/8" or # 19258 for a 2" ball. I have attached some installation videos below for your reference.
  view full answer...
• Parts Needed to Tow With 2006 Toyota Matrix XR & Can Bikes be Brought
  I'll just rip this band-aid off as fast as I can but there is just not a way to use a standard hitch-mounted bike rack and tow at the same time with your 2006 Toyota Matrix XR. The issue, like you said, is the 1-1/4 inch hitch not having an adapter; even if it did though, hitch adapters reduce hitch capacity by 50% so you'd be going over that as well. The only solution would be to add a roof rack and two roof-mounted bike racks, and that's awful expensive for one trip. If you want to do...
  view full answer...
• Hitch and Trailer Recommendation for a 2011 Chevy HHR
  The only way you could transport a 500 handicap scooter with your 2011 Chevy HHR would be for you to install a hitch like part # 24756 and then use a small trailer. A cargo carrier setup wouldn't work because your vehicle wouldn't have the tongue weight rating to suspend the weight of your 500 lb wheel chair off the ground unsupported. To complete your towing setup you would also want a ball mount, the # 118407 for trailer wiring, # 19256 for a 1-7/8 inch hitch ball, and # 19258 for a...
  view full answer...
• Sport Trailer With 15 Inch Hitch Ball Height
  I have a great option that is going to work for you, though I checked with Yakima, and to use the Rack and Roll Trailer # Y08107 the top of the hitch ball must be 22" off the ground. An inch or two in either direction would work, but the seven inch difference you have would make the trailer susceptible to fishtailing due to the uneven tongue height. With that said, there is a similar trailer that is going to work very well for you, the Malone MicroSportXT Trailer # MPG460XT, which requires...
  view full answer...
• Class II Ball Mount with 1-1/4" Shank Needed that has a 5" or 6" Rise/Drop
  I am attaching a link to all of our Class II ball mounts that fit a 1-1/4" receiver opening. Since adjustable ball mounts are geared towards vehicles that tow regularly, like pickups, they don't make any that fit a 1-1/4" receiver. Among the linked ball mounts we have the Draw-Tite # 36078 which has a 5" drop or the Draw-Tite # 36065 which has a 5" rise, both of which are rated for 3,500 lbs. Either of these ball mounts are compatible with the 1-7/8" Hitch Ball # 19256 rated at 2,000...
  view full answer...
• Parts Needed To Tow Lightweight Trailer With 2019 Toyota Camry
  To tow the lightweight kayak trailer with your 2019 Toyota Camry you will need a hitch, wiring, ball mount with ball, and a pin with clip. For the hitch, I recommend Class I Curt Trailer hitch receiver part # C11576 which is a 1-1/4" hitch receiver and fits the hybrid model. I have attached a video for your reference. You will also need wiring to illuminate the trailer lights. I recommend the Curt T-connector 4-pole flat part # C34FR which will plug in behind the tail lights. When we...
  view full answer...
• Recommended Trailer Hitch and Wiring for 2010 Hyundai Accent
  Starting with the trailer hitch for your 2010 Hyundai Accent, I do recommend the Draw-Tite Class I Sport Frame Receiver Hitch # 24795 referenced in your question. This is a Class I hitch that will provide a towing weight capacity of 2,000 pounds. I like this model over the Curt alternative also confirmed to fit your vehicle because unlike Curt, Draw-Tite does not require the use of stabilizing straps like # 18050 with non-trailer loads such as bike racks and cargo carriers. After your move...
  view full answer...
• Will Draw Bar 36065 fit a 2012 Nisssan Sentra
  There is a drawbar with 5" of rise that will work for you, but Draw-Tite # 36065 is for use with Class II hitches only, and is not compatible with your Class I hitch, # 24794. Instead, you could use the Curt # C45024, a Class I draw bar which also gives you 5" of rise and will have no problems clearing your bumper with a length of 9-9/16". For a hitch pin you would want # F-4, and the hitch ball you want would either be 1-7/8" ball # C40001 or 2" ball # C40018.
  view full answer...
  
• Ball Mount with 4 or 5 Inch Rise for a 1-1/4 InchCurt Hitch on a 2016 Honda HR-V
  For the Curt hitch # C11416 the recommended ball mount is # C45521 which is 7-1/4 inches long. So as far as length goes the average on the recommended mounts is about 7 inches but it can be longer. The rise on these recommended ball mounts isn't enough though. For a 4 inch rise you could use # 3594. For a 5 inch rise use # 36065. And for either ball mount you can use # 19256 for a 1-7/8 inch ball or # 19258 for a 2 inch ball. For a trailer wiring harness you can use # 118673 to add a...
  view full answer...
• What is the Height With and Without Rise on Ball Mount for 2016 Ford Fusion
  For your 2016 Ford Fusion, the Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" # C12091 is a confirmed fit. This hitch will be 10-3/4 inches from the ground to the inside top of the receiver opening. When using a ball mount like # C45016, this will give you a 2-5/8 inch rise from that location giving you 13-5/8 inches from the ground in that rise position. In the drop position, the top of the mount or bottom of the actual hitch ball will be at 7-3/8 inches from the ground....
  view full answer...
• Trailer Hitch Recommendation for a 2008 Dodge Avenger R/T
  The Draw-Tite Trailer Hitch # 36448 is a confirmed fit for your 2008 Avenger R/T and is a great fit for your light-duty towing and hitch rack needs. The hitch exceeds industry strength standards. The recommended wiring for your vehicle is the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118445. I have added a link to that part. The recommended ball mount is # 36065 and I have added a link to that part too. If you require a 2" diameter hitch ball we recommend #...
  view full answer...
• Using a 36078 Class II Drop Drawbar as a Rise Instead of a Drop
  The drawbar you mentioned is not intended to be used in the rise position and would only create a 3-1/2 inch rise. We do carry a 5 inch and a 3-1/8 inch rise drawbar (see links below) that will fit the Class II hitch. These drawbars all have a tongue weight capacity of 300 lbs and a towing capacity of 3500 lbs. Keep in mind that if you need a significantly higher or lower drawbar to tow (you are not able to use the manufacturer's recommended drawbar for the hitch), you will void the manufacturer's...
  view full answer...
• Ball Mount and Wiring Recommendation for Draw Tite Hitch that Fits 2005 Pontiac G6
  The Draw Tite hitch part # 36426 that you referenced does not come with a ball mount but we do offer the recommended ball mount from Draw Tite as # 36065. This will give you a 5 inch rise. For hitch balls you'd want the part # 19258 for a 2 inch ball or part # 19256 for a 1-7/8 inch ball. If you are unsure what size ball you need check the coupler on your trailer as it will be listed there. You'll also need trailer wiring to activate the lights of the trailer you plan to tow. For that...
  view full answer...
• What is the recommended Draw Bar for a 1999 Cadillac DeVille
  The manufacturer recommended drawbar for your Cadillac DeVille is part number 36063 which has a 3-1/8 inch rise and 11-3/4 inch long distance between the center of the hitch pin hole and the center of the ball mount hole. When towing with a class II trailer hitch, the ball mount that is recommended by the manufacturer should be used. All class II trailer hitches are tested and rated with the specific ball mount for that hitch. Using a ball mount that is not recommended by the manufacturer...
  view full answer...
• Is the Material of Curt Class II 1-1/4 Inch Hitch # C45015, Solid Steel or Tubular Steel
  The Curt Class II 1-1/4 Inch Ball Mount, part # C45015 has a solid steel shank. It has a 5 inch rise and measures 11-5/8 inches from the center of the hitch pin hole to the center of the ball hole. The other choices I have for a 1-1/4 inch ball mount with a 5 inch rise is the Curt Class II 1-1/4 Inch Ball Mount, part # C45014 which is 9-5/8 inches long and the Draw-Tite Class II 1-1/4 Inch Ball Mount, part # 36065 which is 10 inches long. Both of those ball mounts will also have solid...
  view full answer...
• What is the Finish on the Class II Drawbar 5 Inch Rise Kit, 36065
  The finish on the Class II Drawbar 5 inch Rise (Kit), # 36065, is a black powder coat.
  view full answer...
• What Size Ball Hole do Ball Mounts that Fit 1-1/4 inch Hitches Have
  All of the Class II ball mounts out there have a 3/4 inch diameter ball hole. It might be the best solution for you to replace the ball you have with one that will fit that ball hole size like what comes with the # 36065 that you mentioned. For a 2 inch ball you'd need the # C40018 or for a 1-7/8 inch ball # C40001 and you'd be set.
  view full answer...
• Can a Class II Ball Mount be Used with a Class I Trailer Hitch on a 2006 Mitsubishi Eclipse GT
  With a Class I trailer hitch on your 2006 Mitsubishi Eclipse, you should only use the ball mount that is recommended for use with the trailer hitch. Another problem is that the ball mount that you have referenced is a Class II accessory. Class II items are designed so that they will not fit in a Class I trailer hitch. You could use Sportframe Drawbar, # 3592, which will give you a 2-1/8 inch rise or # C45016, which will give you a 2-5/8 inch rise.
  view full answer...
• Recommended Ball Mount and Other Towing Accessories for 2011 Chevy HHR
  For your 2011 Chevy HHR, our friends at Draw-Tite recommend the 4 inch Rise Sportframe Drawbar, part # 3594. To complete your towing system, you might also need the following: 1-7/8 inch trailer ball, part # 19256 2 inch trailer ball, part # 19258 Pin and clip, part # PC2 Locking hitch pin, part # e98879 Trailer Wiring Harness, part # 118407 To see the recommended products and to view a wiring install video, click on the provided links.
  view full answer...
• Ball Mount Recommendation for 2012 Chevrolet Cruze With 1-1/4 Inch Trailer Hitch
  We have a couple different style ball mounts that will work with the hitch on your Cruze. For a standard ball mount I recommend the Curt, part # C45522. This ball mount has a 3-7/8 inch rise to help provide a bit more ground clearance. For a 1-7/8 inch hitch ball I recommend part # C40001, and for a 2-inch ball I recommend part # C40018. If you like the looks of the Euro ball mounts I recommend part # C45592 that comes with a 2-inch hitch ball and I recommend part # C45591 for a 1-7/8...
  view full answer...
• Trailer Hitch For A 2013 Buick Lacrosse
  Hello Gregg. We do offer a trailer hitch for your 2013 Buick Lacrosse, the Curt Trailer Hitch Receiver # C12115. This is a class 2 hitch, it has a 1-1/4" receiver and is rated for towing up to 3,500 lbs or 350 lbs of tongue weight. So, more than enough for a light boat and trailer. I also recommend that you get the Curt T-Connector # 56098 which will definitely be the most convenient wiring option for your Buick. You will also need a ball mount such as part # 36065 as well as a 1-7/8" ball...
  view full answer...
• Trailer Hitch Recommendation for 2009 Hyundai Genesis Sedan
  The Class III and IV trailer hitches are designed for higher capacity, larger vehicles like SUVs and trucks that have higher towing capacities. The hitches we have for your 2009 Hyundai Genesis are lower in capacity like the Draw Tite Class II part # 36486 which has a 300 lb tongue weight capacity. Best option would be to go with a small trailer if this is the only tow vehicle you have. I attached an install video for this hitch for you to check out as well. You'll want to check your owners...
  view full answer...
• Ball Mount Recommendation for a 2017 Chrysler Pacifica with Draw-Tite Trailer Hitch 36798
  Your assumption is correct. If the distance from the ground to the top of the receiver opening on trailer hitch # 36798 is 12 inches, and the distance from the ground to the bottom of a level trailer coupler is 17 inches, you would need a ball mount with a 5 inch rise. Ball mount # 36065 is a good option. It takes a ball with a 3/4 inch diameter shank. For a compatible 1-7/8 inch ball you can use # 19256. For a 2 inch ball use # 19258. For trailer wiring if your 2017 Chrysler Pacifica...
  view full answer...
• Can The Draw-Tite Ball Mount, # 36065, Be Turned Over And Used As A Drop On a Mercury Mountaineer
  A 1-1/4 inch hitch receiver is either a Class I or Class II hitch. All Class I and Class II can only use the ball mounts that are recommended for that vehicle. For safety reasons, if you have to change the rise or drop from the recommended ball mount, then the manufacturer does not recommend to tow that trailer with the Class I or Class II hitch on your vehicle. We have Class III hitches available for Mercury Mountaineers that will bolt on underneath the OEM 1-1/4 hitch. The Class III...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?