See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Best Trailer Hitch Receiver for a 1999 Buick LeSabre
  We currently only have one trailer hitch receiver for your 1999 Buick LeSabre which is the Draw-Tite Trailer Hitch Receiver part # 36216. This option will give you a Class II hitch with a 1-1/4" receiver tube opening. I have attached an installation video on a similar 1997 Buick LeSabre for you as well. If you can tell me what you will be using the hitch for I would be glad to offer some additional recommendations for you as well.
  view full answer...
• Trailer Hitch and Wiring Recommendation for 2014 Chevy Impala
  We have hitches that fit your 2014 Chevy Impala like the Draw Tite Class II hitch part # 36543 which is what I recommend. It installs easily and also gives you a mostly hidden solution. This is a bolt on hitch that does not require any welding. For trailer wiring our most reliable option is the Tekonsha # 118590 which I recommend for you. For a ball mount the # 36061 is the required part number and then for a ball # 19257.
  view full answer...
• Trailer Hitch and Wiring for a 2015 Cadillac XTS VSport
  Draw-Tite trailer hitch # 36538 is listed as a fit for all styles of the 2015 Cadillac XTS so that will include the VSport model. If you plan on doing some towing the proper ball mount for this hitch is # 36061. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring you can use # C59496 to add a 4-Way flat connector to the rear of the vehicle.
  view full answer...
• Is the Drawbar Pin and Clip Included With Draw-Tite, 36423, Class II Receiver Hitch on 2009 Jeep
  No, the draw bar, pin and clip are not included with the Draw-Tite Class II Trailer Hitch, part # 36423. The manufacturer recommended drawbar for the 2009 Jeep Patriot is, part # 36061, which needs to be used in the rise position only. You will also need a hitch pin and clip, part # PC2, and a properly sized hitch ball, part # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). If you do not already have trailer wiring, you will need the T-One Vehicle Wiring Harness, part # 118552,...
  view full answer...
• Which is the Correct Ball Mount for a 1997 Lexus ES 300 and Draw-Tite Class II Trailer Hitch
  The trailer hitch # 36336 for the 1997 Lexus ES 300 is a Class II trailer hitch. This is important because with Class II trailer hitches you have to use the ball mount specified by the hitch manufacturer or it voids the hitch warranty. This is because on the lower Class hitches they are tested with a specific ball mount best suited for the vehicle. When measuring for the rise or drop needed you do not factor in the height of the ball. I have included a link to a how-to article that explains...
  view full answer...
  
• Trailer Hitch Recommendation for a 2014 Chevy Malibu
  Unless your Chevy Malibu is a 2014 model the part # 36543 that you referenced would not be the correct hitch for you. Instead you would want the Draw-Tite part # 36538 as it is the correct hitch for your vehicle and would work well. For trailer wiring you would want the part # 118602 for if you have an LTZ model or part # 118576 for if you do not have an LTZ model. You will need the recommended ball mount, part # 36061. For hitch balls you would want the part # 19256 for a 1-7/8 inch...
  view full answer...
• Trailer Hitch and Class II Drawbar for a 1995 Mercury Cougar Come with Hardware
  The hitch you are looking at for your 1995 Mercury Cougar, the Class II Frame Trailer Hitch Receiver Hitch, item # 36179, includes all necessary installation hardware as shown in the instructions (see link). The Class II Drawbar 3-1/8 inch Rise Kit, item # 36061, does come with the pin and clip. Most trailer couplers sit at 17 inches from the ground, so we have specifically matched this draw bar with this rise to your vehicle to accomplish the height you will need. Some items you may...
  view full answer...
• Correct Ball Mount for a 1995 Buick Riviera
  I am not sure which draw bar you have, but the recommended draw bar for your vehicle and trailer hitch is the Class II Draw bar 3-1/8 inch Rise, part # 36061. None of the hitches or draw bars we carry have tapered receivers or shanks, so the only thing I can think of is that you have a Class 1 hitch and a Class 2 draw bar which are not compatible with each other even though they have the same 1-1/4 inch by 1-1/4 inch shank. . The Class 2 shank will not fit in a Class 1 hitch, but a class...
  view full answer...
• Recommendations and Installation Instructions for a Wiring Harness on a 2009 Dodge Grand Caravan
  For a 2009 Dodge Grand Caravan, you would use a T-One Harness, part # 118552. A T-One harness plugs into the factory taillight connectors. I have included links to the product page and instructions for installation. You might also need the following: For a 2 inch Receiver: Ball Mount Part # 2753 2 Inch Trailer Ball Part # 19247 1-7/8 Inch Trailer Ball Part # 19260 For a 1-1/4 Inch Class II Receiver: Ball Mount Part # 36061 2 Inch Trailer Ball Part # 19258 1-7/8 Inch Trailer Ball Part...
  view full answer...
• Recommended Trailer Hitch Receiver And Wiring For A 2005 Toyota Camry
  The only hitch receivers we have as a confirmed fit for your 2005 Toyota Camry are both Class II 1-1/4 inch hitch receivers. Unfortunately there is not a confirmed fit 2 inch receiver for your vehicle. We currently have two options for your Camry. We have the Draw-Tite receiver, # 36336 which has a 300 lb tongue weight and 3500 lb towing capacity or we have the Curt receiver, # C12339 with a 350 lb tongue weight and a 3500 lb towing capacity. These hitches are very similar, but the...
  view full answer...
• Trailer Hitch Fit Recommendation for 2014 Chevy Impala Limited
  For your 2014 Chevy Impala Limited the Draw Tite hitch part # 36407 that you referenced has been a confirmed fit and would work well. For trailer wiring you then would want the part # C59236 which has been confirmed as a fit. The ball mount you would want is the part # 36061. For hitch balls you would want the # 19258 for a 2 inch ball and part # 19257 for a 1-7/8 inch ball.
  view full answer...
• How Hard is it to Install a Trailer Hitch on a 2013 Cadillac XTS
  The installation difficulty for Draw-Tite trailer hitch # 36538 for a 2013 Cadillac XTS is listed as a 5 out of 10. The scale is based on estimated time to install the hitch with each tick on the scale representing 10 minutes. So at a 5 it would take a professional approximately 50 minutes to perform the installation. We usually estimate a novice will take twice as long so that would be 1 hour and 40 minutes. If you plan on doing some towing the recommended ball mount is # 36061 and it...
  view full answer...
• Will Draw-Tite Trailer Hitch # 36450 Fit a Hybrid 2009 Saturn Vue
  According to Draw-Tite, trailer hitch # 36450 will fit all models of the 2009 Saturn Vue including Redline models and hybrids. I have included a link to the installation instructions for you to view. If you plan on doing some towing the correct ball mount is # 36061 and you can use pin and clip # PC2. For a 1-7/8 inch diameter ball use # 19256, and for a 2 inch ball use # 19258. For trailer wiring use # C56026, installation instructions linked. The other hitch you referenced, 36479, does...
  view full answer...
• Trailer Hitch and Towing Capacity of a 2008 Chevrolet Impala
  From my research the 2008 Chevy Impala can tow up to a 1,000 pound trailer. You want the loaded trailer to stay under 1,000 pounds. As far as not scraping the ground I'm not sure what you're referring to but if the trailer is not overloaded and is loaded with the tongue weight between 10 and 15 percent of the trailer's weight then you shouldn't have any issues. You also want to make sure the trailer is level when towing. As for the hitch receiver I recommend the Draw-Tite # 36407. ...
  view full answer...
• Will the Trunk Open on a 2007 Chevrolet Impala With a Trunk Mounted Bike Carrier
  You would not want to open the trunk while a trunk mounted bike rack is installed on your 2007 Chevrolet Impala because it could cause damage to the vehicle. If you would like to have access to your trunk without having to remove the bike rack every time, then I would recommend adding a hitch and hitch mounted bike rack. For your vehicle, I would recommend the Draw-Tite Class II Hitch, # 36407. There will be no contact between your vehicle and a hitch mounted bike rack and you will be...
  view full answer...
• Recommended Ball Mount for Class II Hitch Installed on 2003 Chevy Venture
  The recommended ball mount for your 2003 Chevy Venture for the Reese Class II hitch you have installed on your 2003 Chevy Venture is the Draw Tite part # 36061. Then for hitch balls you'd want the part # 19258 for a 2 inch ball or part # 19257 for a 1-7/8 inch ball.
  view full answer...
• Trailer Hitch Recommendation and Towing Capacity for 2003 Toyota Camry
  I'd recommend confirming this with the owners manual of your 2003 Toyota Camry, but I was able to find a 2,000 lb towing capacity for your vehicle which should be adequate for a motorcycle trailer like you plan on towing. Now we have Class II hitches available for your vehicle like the Draw Tite part # 36336 which are rated higher than that at 3,500 lbs trailer weight, but you have to go with the lowest rated component in your tow setup as the overall capacity as you're only as strong...
  view full answer...
• What is the Towing Capacity for a 2001 Subaru Outback and Trailer Hitch and Wiring Recommendations
  It took a little research but I was able to find the towing capacity information for the 2001 Subaru Outback in the online owner's manual. For manual transmission models and a trailer with no brakes the towing capacity is 1,000 pounds; with brakes it is 2,000 pounds. It is the same for automatic transmissions (1k without brakes or 2k with brakes) but also Subaru says: When towing a trailer on a long uphill grade continuously for over 5 miles (8 km) with an outside temperature of 104°F...
  view full answer...
• How to Choose the Right Ball Mount to Tow a Trailer Level with a 2003 Toyota Camry
  To choose a ball mount with the correct rise and drop, you'll first need to take two measurements: your hitch height and trailer coupler height. The difference between them will be your rise or drop. To take the first measurement make sure the vehicle is on level ground and measure from the ground to the top of the receiver opening. On hitch # 36336 for your 2003 Toyota Camry that measurement is approximately 12 inches. To take the second measurement make sure the trailer is on level...
  view full answer...
• Towing Capacity and Trailer Hitch Recommendation for 2017 Chevy Impala
  From what I found online it looks like your 2017 Chevy Impala has a towing capacity of 1,000 lbs. If the weight of your trailer loaded is less than 1,000 lbs then yes you could tow it. For a hitch then we have the Draw Tite part # 36538 which is a confirmed fit for your vehicle and would work well. For a ball mount you'd then want the # 36061 which is the recommended ball mount by Draw Tite. For a hitch ball part # 19257. For trailer wiring you'd then want the Tekonsha kit part # 118590...
  view full answer...
• Can the # C45519 Ball Mount be Used on a 2004 Buick Park Avenue and How Long Should the Drawbar Be
  My fit guides show that your vehicle uses the Draw-Tite Ball Mount, item # 36061, in the rise position only. You would not be able to use this draw bar in the drop position. The manufacturer of the hitch does safety testing that puts the drawbar and ball in the best position, in case of an accident, and we cannot recommend using a draw bar in a different position or with a different rise or drop. We have an FAQ on hitch Classes for you to review, see link. The Draw-Tite Ball Mount, item...
  view full answer...
• Hitch Recommendation for a 1997 Oldsmobile 88 for Towing
  For a hitch confirmed to fit your 1997 Oldsmobile 88 you would want the Draw Tite Hitch part # 36211. This hitch will attach to the frame of your vehicle and has towing capacities of 3,500 lbs total trailer weight and 300 lbs tongue weight. You will need to check the owners manual of your vehicle to determine the capacity for the vehicle and be sure not to exceed this figure. To complete your towing setup you may also be interested in the following products. Class II Drawbar 3-1/8" Rise...
  view full answer...
• Recommended Trailer Hitch, Ball Mount, Trailer Ball and Trailer Wiring Harness for 2015 Toyota RAV4
  There are both Class II and III hitches available for a 2015 RAV4, but I'd recommend going with a Class III, because there is a much better selection of hitch mounted accessories available for the more common 2 inch Class III receiver. The Class III version, # C13149 is very similar in price, and would provide much more flexibility. I've linked an install video for you. Since you'll be towing, you'll also need a wiring harness like # 118578. I've lilnked to an install video that will help...
  view full answer...
• Trailer Hitch and Wiring for a 2001 Ford Taurus to Tow Riding Mower/lawn Service Equipment
  There are Class I and Class II trailer hitches available for your 2001 Ford Taurus. The Class II trailer hitches are going to have a higher capacity and thus be stronger than the Class I options. Based on that I recommend going with a Class II hitch # C12232. The hitch itself is rated for 300 pounds tongue weight and 3,500 pounds gross trailer weight. But consult the vehicles owners manual for the vehicle towing capacity and if lower, go by the lower of the two ratings. For a ball mount...
  view full answer...

Do you have a question about this Trailer Hitch Ball Mount?