See what our Experts say about this Draw-Tite Trailer Hitch Ball Mount

• Hitch Recommendation for 2003 Honda Accord EX 4-Door Sedan for Use with Out-Sider ASL-250 Lift
  All of the hitch receivers offered for your 2003 Honda Accord are the 1-1/4-inch size and rated as Class I hitches. Class I hitches are considered suitable for light-duty use, such as with 2-bike racks, small cargo baskets and for light towing applications. The 142-lb Out-Sider ASL-250 Platform Lift is intended for use with 2-inch Class II or Class III receivers and so is not compatible with the 1-1/4-inch Class I hitches available for your Accord. You cannot use a hitch adapter in your...
  view full answer...
• Trailer Hitch, Wiring Harness and Ball Mount Recommendation for 2019 Toyota Prius
  The trailer hitch I highly recommend for your 2019 Toyota Prius is the Draw-Tite # 24966 because it has a concealed crosstube and is a bolt-on installation that will not require drilling into your vehicle's frame to install. This Class I, 1-1/4 inch trailer hitch is almost entirely hidden behind your bumper, as you can see by the accompanying photo, allowing your Prius to maintain a clean look. The hitch, which comes with a lifetime warranty, has a black powder coat finish to protect it...
  view full answer...
  
• Replacement Hardware for Draw-Tite Trailer Hitch Receiver to Move From 2016 to 2017 Ford Fusion
  To order the exact original hardware that was included with the Draw-Tite # 24897 use part # RHK. Choose "Draw-Tite" from the drop down and then enter the part number into the box. All of our prices are on the product pages and I've also linked an install video for you on a 2016 Fusion.
  view full answer...
• 1-1/4 Inch EcoHitch InvisiHitch for 2015 Subaru Impreza
  We do indeed offer the EcoHitch X7212, which we offer as part # EH22RR which is compatible with the 5 door wagon Impreza models with a single exhaust and the knockout panel on the rear bumper face. If you'll be using the hitch for light duty towing, you'll also need a trailer wiring harness like # 118573, a ball mount like # 3592 and # 19256 for a 1-7/8 or # 19258 for a 2 inch trailer ball.
  view full answer...
• Trailer Hitch Receiver Fit for 2009 Mazda 3
  Yes, I can confirm that the Draw-Tite hitch you asked about does fit your 2009 Mazda 3: - Draw-Tite Trailer Hitch Receiver # 24816 To tow you will need the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118420 if your Mazda does NOT have LED tail lights or # 46255 if it DOES have LED tail lights. You will also need Ball Mount # 3592 and either 1-7/8" Hitch Ball # 19256, or 2" Hitch Ball # 19258. I have added links to video reviews for you to check out as well, including...
  view full answer...
• Trailer Hitch that Fits 2009 Ford Fusion
  We have the Curt trailer hitch # C11329 for the 2009 Ford Fusion that has a towing capacity of 2,000 lbs. This capacity though is independent of the capacity of your vehicle. I tried looking up the capacity for it online and most places say it wasn't listed or it's not rated for any towing. So I really wouldn't feel comfortable telling you that your vehicle could tow a 1,500 lb trailer. Especially on the hills you describe. If you really wanted to do it though I would recommend checking...
  view full answer...
• Will Curt Trailer Hitch C11281 Fit a 2013 Dodge Dart SXT Rally with Dual Exhaust
  I checked with Curt and trailer hitch # C11281 will fit all models of the 2013 Dodge Dart including those with dual exhaust. I have linked the installation instructions for you. If you are planning on doing some towing check your owner's manual for the towing capacities of the vehicle. If none are listed, then contact Dodge to determine what the capacities are if there are any. If you can tow, then the correct ball mount to use is # 3592. For a 1-7/8 inch ball use # 19256 and for a 2-inch...
  view full answer...
• What Do I Need to Use Hitch C11109 with my 2004 Chevy Cavalier
  The hitch, # C11109, includes all the mounting hardware you need to install the hitch to your 2004 Chevy Cavalier. In order to tow a trailer, you also need to purchase a drawbar, and the ball itself that sits on the drawbar. The drawbar for this hitch is part # 3592. This bar includes a hitch pin and clip. Your drawbar requires a ball with a shank diameter of 3/4 inch. I have added a page link that will show you all the balls that would fit your drawbar. You need to select the ball diameter...
  view full answer...
• Trailer Hitch for 2002 Chevy Cavalier LS
  The hitch that fits for your 2002 Cavalier LS is the Curt Trailer Hitch Receiver # C11109. If you were planning on using the hitch for light duty towing, you'd need the following items to complete your towing set-up: Trailer wiring harness, part # 18252 Ball mount, part # 3592 1-7/8 inch ball mount, part # 19256 or 2 inch ball mount # 19258
  view full answer...
• Hitch Recommendation for a 2003 Honda Accord with a Factory Body Kit
  I spoke with my contact at Draw-Tite and he informed me that they do not have any fit information for the 2003 Honda Accords with body kits. The best solution he could recommend for you is to check out the installation instructions for this product and compare them to your vehicle to see if you think it would work. I attached installation instructions and a installation video for this product for you to check out also. You may be interested in the following products to complete your towing...
  view full answer...
• Can 2018 Honda Accord Tow Small Motorcycle Trailer
  We do have hitches that fit your 2018 Honda Accord Sport so with one installed like the Draw Tite part # 24972 you could tow a small trailer like you mentioned. You'd also need trailer wiring like the # C56402 and a ball mount # 3592.
  view full answer...
• What is a Drawbar and Why Would I Need One?
  The hitch drawbar or ball mount is the part that slides into the hitch receiver that has the trailer ball bolted to it. You'll need the ball mount if you plan on towing, but if you're only using the hitch as a mount for a hitch mounted accessory like a bike rack or cargo carrier, you won't need it. If you need a ball mount that's compatible with the Curt Class I hitch, part # C11256, I'd recommend # 3592. For 1-7/8 inch trailer ball, use # 19260 or # 63845 for a 2 inch ball. For a trailer...
  view full answer...
• Why do Some Ball Mounts Have a Drop and Rise and Others Only have a Rise
  Some ball mounts, generally Class I and Class II ball mounts, are designed by the manufacturer for use in the rise position only. These ball mount designs are intended for use with vehicles that require a rise only and would be too low to the ground to ever need a lower ball mount. Ball mounts listed with a rise only should not be used in the lowered position because the manufacturer has not tested them for use in that position. Some Class I and Class II ball mounts, like item # 3592,...
  view full answer...
• Class II Ball Mounts and Bike Racks Will Not Fit a Class I Trailer Hitch on a Mazda 5
  The trailer hitch you have, # 24874, is a Class I trailer hitch. The accessories you are trying to use must be Class II accessories and will not fit. That tab inside the shank is a safety stop. It is there to prevent you from overloading the Class I hitch which could damage it or the vehicle. We started pointing this out on all of the Class I trailer hitch product pages, see picture, after numerous comments from customers having the same problem. The correct ball mount for this hitch and...
  view full answer...
  
• Trailer Hitch for 2003 Chevy Corvette Towing a Harley Davidson on a Trailer Weighing 900 lbs Total
  The Curt trailer hitch # C11034 has a gross trailer weight capacity of 2500 pounds and tongue weight capacity of 250 pounds. The weight of the trailer plus the bike would be 900 pounds so you are well under the capacity of the hitch. However, you have to also consider the towing capacities of the vehicle. A Corvette is not typically a vehicle used for towing so capacity information or anything related to towing may not even be in the owners manual but you will want to check there first...
  view full answer...
• Recommended Towing Package for a 2007 Honda Accord
  For your 2007 Honda Accord, I recommend taking a look at the Draw-Tite Sportframe Trailer Hitch Receiver part # 24787. This hitch has a Class I rating with a 1-1/4" receiver tube opening. The maximum gross trailer weight (GTW) and tongue weight (TW) this hitch can handle is 2,000 lbs and 200 lbs respectively. This is the only trailer hitch receiver that we have confirmed to fit your vehicle that does not require drilling for installation and is completely bolt-on. I have also attached an...
  view full answer...
• 2007 Honda Accord V6 Sedan Towing Capacity and Hitch Recommendation
  To answer the most basic part of this question first, you are correct that only Class I hitches with 1-1/4" receivers are available for your 2007 Honda Accord, but if your weight estimates are correct, they will be sufficient to handle this job. I did some research and according to the owner's manual of the 2007 Honda Accord, it has a 1000-lbs towing capacity; it also looks like your Yamaha YZF R1 has a wet weight of around 450-lbs. As long as your total weight of trailer and bike stay...
  view full answer...
  
• Trailer Hitch Receiver and Wiring Harness For a 2019 Infiniti Q50 Red Sport
  According to Draw-Tite their Sportframe Trailer Hitch Receiver # 24931 fits all models including the Red Sport trim on your 2019 Infiniti Q50. Draw-Tite recommends using the Ball Mount # 3592 with a 1-7/8" # 19257 or 2" # C40018 hitch ball. You will be able to hold the ball mount using a Pin and Clip # F-4 or you can secure it with the trailer using the Master Lock Trailer Hitch Receiver Lock and Coupler Lock Set # 3794DAT. The Curt T-Connector Vehicle Wiring Harness # C56248 will provide...
  view full answer...
• Recommended Trailer Hitch for 2013 Dodge Dart Rallye
  From my research I found that the towing capacity for your 2013 Dodge Dart Rallye has a maximum towing capacity of 1,000 lbs. This would be the weight of any trailer you attach added to the weight of the cargo on the trailer. The hitch I recommend is the Curt Trailer hitch, part # C11281. This is a Class l hitch and has a 1-1/4 inch receiver opening. The ball mount I recommend is the Draw-Tite Ball Mount, part # 3592. This fits 1-1/4 inch receivers and uses hitch balls with a 3/4...
  view full answer...
• Recommendation For Trailer Hitch For 2002 Honda Accord 2-Door Coupe
  Yes, I have a hitch for you! I recommend the Curt Trailer Hitch Receiver, Item # C11290, that is a confirmed fit for your 2002 Honda Accord Coupe. It is a Class I, 1-1/4 Inch light duty hitch that lets you tow a trailer, carry a bike rack, or carry a cargo carrier. It has a maximum capacity of 2,000-lbs and a maximum tongue weight of 200-lbs. It bolts on and is very durable. This hitch is a confirmed fit but keep in mind that your Honda has a maximum towing capacity of 1,000-lbs so...
  view full answer...
• Will I Have to Drill into the Frame of My 2003 Chevy Cavalier to Install Curt Hitch # C11109
  In order to install this Curt Trailer Hitch # C11109 on your 2003 Chevy Cavalier, you will only need to use a drill to enlarge some existing holes. You will have to temporarily lower your exhaust, but the exhaust will be reinstalled when the installation is complete. You will also need to trim the heat shield. I attached the instructions in a link below for you to check out also. You may also be interested in purchasing the following: Sportframe Drawbar 2-1/8 inch Rise or 2-3/4 inch...
  view full answer...
• Can Class I Hitch Vehicle Tow Trailer Designed for Motorcycle
  As long as you have the correct trailer wiring on the tow vehicle to match what the trailer needs and the correct hitch ball size and drop there's no reason you couldn't tow a small trailer designed for a motorcycle with a vehicle that has a Class I hitch.
  view full answer...
  
• 2018 Prius Prime Trailer Hitch Recommendation
  For your 2018 Toyota Prius Prime we have the Draw Tite hitch part # 24966 as a confirmed fit. The hitch by itself has a capacity of 2,000 lbs trailer weight. You'd need to check the owners manual of your vehicle and be sure to stay under the capacity listed there for towing too. For trailer wiring you'd then want the part # C56371 which is a confirmed fit. I attached an install video for this for you to check out as well. For a ball mount then you'd need the part # 3592 and hitch ball...
  view full answer...
  
• Can a 2015 Nissan Versa Carry a Wheelchair and Lift on a Trailer Hitch
  You can use a cargo carrier in a hitch on your 2015 Nissan Versa. However, all of the trailer hitches for the vehicle, such as # C11256, are Class I hitches which have a low tongue weight capacity (200 pounds) and not very many options for carriers. Wheelchair lifts are often heavy and add to that the weight of the wheelchair itself and it can easily exceed the tongue weight capacity of the hitch if you can find one that is compatible with a Class I hitch. It is possible though to use...
  view full answer...