Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Sturdy steel ball mount with hollow shank measures 9" from center of hitch pin hole to center of ball hole. Angle-cut shank slides easily into your hitch. Powder coat finish over a-coat base provides excellent rust protection.
Features:
Specs:
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (2586 Customer Reviews)
Sturdy steel ball mount with hollow shank measures 9" from center of hitch pin hole to center of ball hole. Angle-cut shank slides easily into your hitch. Powder coat finish over a-coat base provides excellent rust protection.The product is good but a bit tideous and after installing it my bracket fell and it was a pain to get replace it support made me buy the replacement pieces and the bracket didnt come with just the bolts, and at the end they told i have i had to buy the whole unit because based on their system my truck didnt have issues with installement and the manufacturer didnt supply that bracket cause it special order so in general i dont recommend in my choice better to get it welded.
Working in the sand and grass of my driveway my wife and I installed our new etrailer receiver hitch. Great fit and finish! Went right on as described in the online guide. Hitch required a spacer washer on top back bolt attachment point. Taped it on so it would not move while lifting in place and it stayed right there! Used a car jack to raise up and hold the hitch into the underside of the trunk tighten the bolts and reattached the tail pipe done.
Now we can pull our Sunfish Sailboat any where the car will go.
Very knowledgeable group easy to work with I would always continue to use trailer :)
I am very pleased with the hitch, ball mount, and electrical package. All were easy to install if you follow the easy to understand directions. An added plus for putting one of these on a MINI is that the hitch can be hidden behind the "black plate/cover" that is on the rear bumper. It looks just like it came out of the factory except when to need to install the ball mount.
The service has been outstanding. This is the place to go.
Sara R was helpful helping me find the right hitch for what I described as needing.
I was excited to see the hitch pin in my order details even though I didn't order it. Sadly, the picture gave me a false impression.
Overall, excellent customer service and product.
Purchased to use on my 2020 Yamaha Drive 2 golf cart hitch. I ordered this and an 18” receiver extension. When I placed my online order I received a phone call the next morning asking if was aware that the extension and the receiver hitch were different sizes and would not work together. I was very grateful for the call as I had not realized I had ordered items that would not fit together. Great Customer Service!!!
Well built. Make sure you buy the pin separately, as it does not come with the receiver - which I thought would make sense.
Matt D.
4/5/2018
Amazing customer service as usual!I love your products, they are heavily road tested and working excellently! I got a friend to buy a trailer hitch too, since it was so easy!
I purchased hitch number 87506 And (2) 2753 ball mounts. The installation was very easy, the entire job took 20 to 30 minutes. I would recommend etrailer.com to anyone looking for a new hitch for their vehicles.
Well-made, but take note this mount has a 1" hole. I had intended to get a class III ball mount with 3/4" hole. I had to get a new ball because my old one has a 3/4" shank. And a new wrench because my 12 inch crescent wrench is too small for this new nut.
New ball mount/ball and tires/wheels worked like a charm. Everything arrived on time. I'll be getting all my trailer/towing gear from etrailer.com.
Renewed gear hauler set for new adventures. Thanks etrailer!
You have a great website the product was easy to find and well-defined your price with shipping beat the local prices in my area. The shipping was fast and delivered right to my door. Oh yeah the online tracking of the package was really great. Thank you etrailer.
first time I have ever ordered from etrailers,,,,,FANTASTIC SERVICE!!!!!!!!!!!!!!!! FAST FAST SHIPPING!!!!!!!!!!!!!!!! to me 5+ stars all the way around,,, if I ever need anything again and etrailers has it I will order again,,,, could not ask for better,,, I don't get excited about to many companies but etrailers is top notch
Great Customer service I received my product however parts were missing. I contacted them after hours to inform them. And I received Email inquiring what was missing. The very next day I received another e-mail and thy are sending Me the missing parts. mind you this was over a weekend. Great Customer Service.
Delivery was quick and on time and the mount was what I expected. No issues at all with the order.
Needed to pull a 5x8 trailer with a 22 forester. This ball mount had the perfect rise to brink the hitch ball to 18 & 3/4” at the center of the ball.
This worked great with my Curt hitch for Subaru Outback 2016. It was a right height for the uhaual trailer as I had to use this as a raise rather than drop. Also, the staff at etrailer was very helpful.
Kevin
7/26/2019
Still doing great!
From all appearances, seems to be a solid mount. I will be using this to tow a duel motorcycle trailer. I needed the specific rise to level out a loaded trailer.
David B.
1/27/2015
This is a follow-up review of the mount. At first it was a little too snug for my Valley Hitch, but that may be the rust built up in the square receiver. So after cleaning it out with a file, and greasing the mount, it slid into the hitch just fine. Ive hauled the bike twice, and I can say that this heavy piece of metal will get the job done nicely. Its heavy, well built, and fits. It accepted a 2 ball with no problems. You wont be dissatisfied - but if you are, then there is probably no pleasing you *joking*
My F150 had an OEM 4 pin trailer plug and hitch.
The 118242 - 7 pin connector with wiring harness is the ticket. The hardest part of the install was dropping the spare tire. The plugs connect directly to the factory plugs and the harness length is the correct length.
The 3035-P brake controller connector harness was just as easy. Plugs right in to the OEM plug next to the ECM connector and the other end into the brake controller.
The PK12711U-26 - 7 pin bracket and hardware kit fastens directly the OEM bracket that is on the hitch. My truck had an OEM 4 pin trailer towing set up with the hitch. The OEM hitch had the bracket welded on it to attach the 7 pin mounting bracket to it.
These kits make this install very easy and professional looking.
If I have one complaint, the hardware kit to attach the 7 pin connector bracket is set up to fasten the bracket directly to the bumper with 2 - self tapping screws provided in the kit. The kit also includes 4 #12 machine screws with toothed washer nuts to attached the 7 pin connector to the bracket. This is fine if your truck hitch doesn't have an attaching bracket welded to it. The kit should included in it 6 #12 machine screws and nuts along with the 2 self tapping screws. Since my OEM hitch actually had a bracket welded to it to attach the 7 pin bracket to it, I had to use two other #12 screws and nuts to attach the 7 pin bracket to the OEM bracket on the hitch. Not a big deal, just a thought.
It took me about 2 hours, start to finish to install the 7 pin connector, trailer controller, and add the two relays in the OEM relay/fuse box under the hood.
I highly recommend these kits.
Purchased Hidden Hitch Class 3, 2" hitch for my 2007 Honda CRV along with wiring harness and ball mount. Not the handiest person in the world but after installing this hitch, my handy-ego has been inflated. The videos on the website are spot on and are a huge resource for installation. Support during the sale and after were much appreciated. This is one of my top five e-commerce experiences. Well done etrailer.com!
I give the product and delivery team 5 stars!! THANKS SO MUCH!!
The parts worked perfectly. Look forward to using them for real, off road in the Maine north woods.
Videos extremely helpful.Product was all and even more than expected. The hitch went on without a HITCH, Sorry, couldn't help it. this is how it turned out. would buy again in a heart beat. Thanks
To Whom it May Concern:
I highly recommend etrailer.com com. I ordered a trailer hitch and bike rack by phone. The sales agent was professional, competent, helpful and friendly. The prices of the products are fair and the delivery was timely and arrived in good condition. It is rare to have a purchase experience of the level of high quality that I experienced with etrailer.com. I am highly recommending this company to others, based on my first experience with them, and I would not hesitate to purchase from them again. 4 stars out of 4. Thank you. Jim B., Falmouth Maine.
Used it to raise the hitch ball to level out my camping trailer while towing. It works.
I chose the Draw tight Max Frame Trailer Hitch for its known quality, i like it comes powder coated to reduce unsightly rust and to keep that fresh look.
I chose the this hitch for my all around light and heavy duty needs.
The Draw Tight Ball Mount is a quality enhancement to this hitch.
I chose the 2" chrome ball for its quality and appearance.
The Curt C55515 wire connector was the best choice for my lighting needs.
Do you have a question about this Trailer Hitch Ball Mount?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Tom W.
11/13/2015
Works great.