Great for your heavy-duty utility trailer, this steel piano hinge provides uninterrupted support for your door or tailgate. The hinge rotates 270 degrees and contains no pre-drilled holes, so it can be welded or drilled to match your setup.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello, everybody, this is Jeff at etrailer.com. Today, we're gonna take a look at this 72-inch long, 3-inch wide steel piano hinge. Now, this hinge will provide a nice sturdy, continuous support along the length of your cabinets, your door or your panel. This is great for oversized doors, trailer doors, entrance doors, and what's nice is this will provide more support than multiple small hinges. It is a nice continuous design. Reduces stress on the hinge when used with heavier doors, and it does rotate about 270 degrees.
Wanna zoom in and show you right now, basically you can see if we extend it back it goes about 90 degrees back. And then if we swing it all the way around the other way, it'll go about 180 degrees that way. So in total, it rotates about 270 degrees for a nice full opening and closing motion. It is a durable steel construction. So you would get this open again, there we go.
It does use an unplated mill finish to it, and this is a weld on or bolt on installation, now the bolted on it will require drilling holes into the hinge. This part is made in the USA. I want to give you some specs on this, we'll zoom back out so we'll give you the length. We do the length on this from one end to the other. It's going to be right at 72 inches, so roughly six feet in length.
The width of it at the widest point when it's in the open position. So the open width you can see, let's zoom in so you can see it, you got the widest point, so if we measured that it's going to be writing at three inches wide, but knuckle length, each one of these is a knuckle. So if we've measure the length on those and see its gonna be right at about two inches with the knuckle length and the pin diameter. In other words, the pin that goes through those knuckles that hold these hinges together. Diameter on that pin is gonna be a half an inch.
And again, you can see it rotates. But that should do it for the review on this 72 inch long by three inch wide steel piano hinge..
Average Customer Rating: 4.7 out of 5 stars (181 Customer Reviews)
Great for your heavy-duty utility trailer, this steel piano hinge provides uninterrupted support for your door or tailgate. The hinge rotates 270 degrees and contains no pre-drilled holes, so it can be welded or drilled to match your setup.
This hinge is heavy duty. We have had no issues with the door sense installing. If in need to get rid of hinges that keep getting bent, this might be the hinge you are looking for to do the job.
Just what I was looking for! Great service. etrailer kept me updated on my order and shipping.
I have ordered this product twice. For what I am using them for is outdoor aluminum door. They work great for this application.
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
This is the item I needed and it was sent out and received very fast, very pleased with the product here for my enclosed race trailer to help with my need after I had upgraded my trailer floors & ATP ramp door flap. Item was just as described in the video upon ordering off the website.
Thanks
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Nice heavy duty hinge. We used them as a replacement for the rusted light duty hinge on our custom hunting camp trailer. Received them quickly and in time to installed before the 2022 deer season.
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
used cobalt drill bit drilled 4 holes in hinge on corners with paper to keep door space for future paint ,drilled holes in hinge only just touch wood ,undid 4 screws ,recessed wood with bur thing ,punched stainless hinge into wood, screwed in screws near flush ,very clean super price and strong ,thank you
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Worked out great for my trailer build and made thing a lot easier for making a heavy duty tool box door in the v of a tag trailer
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Worked well on the rear compartment door for my Airstream.
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Used this hinge to replace 2 frozen hinges on our 10 foot enclosed trailer. Because of the full length, we were able to bolt it on instead of welding. We cut the old ones off with a cut off wheel. It worked out great!
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Awesome! Used it on our cargo hauler tailgate ramp. A lot stronger than the original aluminum hinge that pulled apart!
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Used it to replace the cheap factory hinge on my trucks Tonneau Cover. Huge improvement!!
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Correct item received, but tape gum on the hinge will require extensive cleaning before use. Was not necessary to be taped up, Or use painters tape the is easily removable leaving no film.
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
This is exactly what I was looking for. Very fast shipping and high quality of material and the making of the hinge. I would recommend you to everyone. If this project works the way that I hope I will be getting more hinges
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
good product at a good price.
Made my Tailgate extension for enclosed trailer work great
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Good and sturdy. Easy to cut to length - just watch for rod in the middle sliding.
Appears to have taken the black rustoleum spray paint well.
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Wow, shipping was no problem, it shipped in a solid tube and this was the 72” so it’s a long tube. Very heavy gage hinge. Super impressed to get this size in this heavy of a material for this price.
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Heavy duty & exactly what we needed! Th anks!
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Great Service! Didn't have quite the dimension I needed for a one-piece replacement but gave good advice in using to 6' hinges in order to make my 88 1/2" full length hinge. Thank you
Review from a similar Marlboro Continuous Hinge in Trailer Door Hinges
Good hinge. Fast shipping
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.