This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.
Features:
Specs:
Once the brake controller is installed, you can use the knob on the right side of the unit to adjust the gain (also known as output). Gain lets you set the maximum amount of power that will be applied to your trailer's brakes. You want to set it as high as you can without locking up the brakes. Typically, this setting is only readjusted when you experience changing road conditions or if you switch over from a heavy, loaded trailer to a much lighter, empty trailer, or vice versa.
You can fine-tune the gain by adjusting the sensitivity of the internal sensor using the knob on the left side. This controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. You can adjust this when you're towing heavy loads and you need more umph to bring your trailer to a stop. Your tow vehicle doesn't need that much power to brake in time, but your heavy trailer does. A high sensitivity level will get the braking power to your trailer brakes faster and with more intensity so that it doesn't push your tow vehicle forward.
LED Indicator
Keeping with its simple design, the Voyager will not overwhelm you with information. An LED indicator on the top of the unit lights up green to show that your trailer is securely connected to your tow vehicle. The LED indicator will change to red when the brakes on your trailer are activated.
During installation and setup, this light is also used to ensure that the Voyager will be able to function correctly. Proper leveling of the internal sensor is crucial to the operation of this brake controller. When the sensor is level, the LED will change to a shade of orange.
The Voyager is designed to be mounted in your cab at a vertical angle that is between -20 degrees and 70 degrees. The brake controller needs to be horizontally level and parallel to the direction of travel in order to function properly.
To connect the Voyager, just splice the included pigtail harness into your vehicle and then plug the controller into it.
Once the controller is mounted and connected, you must level the internal sensor. First, set the overall power to the maximum using the knob on the side of the controller. Then, while pressing the tow vehicle's brake pedal, adjust the level knob on the other side of the brake controller (this is the same knob that is used to fine-tune the power output) until the LED monitor is a shade of orange.
Note: If you don't already have a 7-way plug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake controller installation kit (ETBC7 - sold separately).
The Tekonsha Voyager brake controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Voyager uses a pendulum system to sense how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today on our 2002 Ford E350 Super Duty Van we're going to be installing the Tekonsha Voyager Trailer Brake Controller, part number 39510. We'll also be installing the Tekonsha adapter plug for Ford vehicles, part number 3035-P. Here's the bracket and here's our Voyager brake controller. We're going to go ahead and kind of just test fit it up here underneath the dash to find a good place. Right here there's a little metal bracket that comes down that we'll be able to screw our bracket into. We'll just line it up and see if that's going to work.
Looks like it will. We'll go ahead and take a couple screws and we'll attach our bracket to this metal section right here underneath the dash. Next we'll go ahead and attach our brake controller to the bracket using the four supplied screws. We'll go ahead and take our adapter plug, take the end that matches up, the side coming off the brake controller, we'll slide it together so that the locking tab clicks into place, then go ahead and route our wire over to this corner right here, the factory connection point for the brake controller. Go ahead and line the plug up, push it into place making sure it clicks into position, then we'll go ahead and use a couple zip ties to help secure our excess wire. Now with our trailer plugged into our 7-way at the rear of the vehicle you can see now that we have the light that comes on on our brake controller showing us that our trailer is connected.
You will need to calibrate and adjust this brake controller for your individual trailer. You'll do that by following the instructions included. That'll do it for our installation of the Tekonsha Voyager Trailer Brake Controller, part number 39510, in conjunction with the adapter plug, part number 3035-P, on our 2002 Ford E350 Super Duty Van. .
Average Customer Rating: 5.0 out of 5 stars (1 Customer Reviews)
This proportional brake controller is designed to keep towing simple. Includes an LED braking indicator, a slide-bar manual override, and a knob to adjust braking power. Mounts easily within a 90-degree vertical range.
I am very satisfied with the Voyager brake Controller I purchased. It is the easiest unit to adjust that I have ever owned. The controls are easy to adjust and it has worked well with my trailers.
etrailer makes the purchase easy. I have always used Tekonsha Voyagers, and on my new truck (2015 Silverado) I also wanted the convenience of having the plug and play wiring harness. etrailer had exactly what I needed and was very easy to find on the website. Installation was flawless and clean thanks to the good hardware supplied. Very excited to put some trailers behind the truck with the stopping power confidence that comes with the Voyager.
The Tekonsha Voyager trailer brake controller works well in my 99 Silverado 1500, which was easy to setup for my trailer. The option to allow for different settings of aggression for the trailer braking has allowed the stopping with different loads to be graceful with the turn of a knob. Decided to install the controller in CD storage with velcro for a nice look. Easy access when in place during use for easy observation and twicking during operation. The wife can assist with the twicking while I am driving. Excellent product!
Purchased a Teckonsha Voyager brake controller and the ETBC7 install kit.
The instruction an video were very clear and easy to follow. Installed on a 2007 Ford Ranger Sport. Tech support was also very helpful on the one question I did have.
Excellent controller, I've had good luck with Tekonsha products in the past and this controller was no different. I went with this model over more expensive options from Tekonsha. Other models have presets for different trailers, however, that would have limited value to me with the wide variety of trailers I pull. Otherwise, I may have made a different choice. I did have to 3d print an adaptor for the controller to sit correctly in my truck, but for my truck that would of been an issue with any proportional controller. I highly recommend this product.
Completely plug and play installation and works flawlessly, very happy with this unit. I also ordered the exact harness for my 2005 f150 with tow package. Here are a couple of hints that may be helpful. My installation also required a 30 amp cartridge fuse to be installed in the fuse panel in location #105(electric trailer brakes) under the dash on the passenger side. I also installed a relay in location r05 (trailer tow battery charge) but I don't think this is needed for the controller to function. I still had the original trailer brake kit and it had the additional fuse panel instructions and the relay. The owners manual showed where the 30 amp fuse and relay plugs in. You cannot test this unit until a trailer with brakes is connected, ie the led will not light up until it senses a brake circuit.
The drawtite hitch and trailer wiring harness fit great. Instructions were clear and concise. Installation was a breeze. I am ready to tow my little trailer now. As soon as I get the brake controller installed, I will be ready for my big trailer.
This is my second Tekonsha; I had to replace my 10-year old one after I accidentally broke it.
This one is a bit of an upgrade, and is easily able to lock up the disc brakes on my 15,000 lb trailer. Adjusting it properly, I'm able to brake as though there were no trailer at all. Set it, and forget it. It doesn't get any easier than that.
If your truck comes with the tow haul package.... this item is literally plug and play. I had it wired up and all mounted inside of thirty minutes. It's literally 4 wires and the stock system wires are labeled along with the brake contoller. I haven't tested it yet but so far I am thoroughly impressed!
Exactly what I was looking for and needed ! It was delivered very quick . Actually I just ordered a complete wiring harness from you tonight . Your service and follow up is great
Perfectly wired directly to existing wiring that I had for the previous brake controller I replaced with the, Draw Tite I Command. This will make it a lot easier should I choose to upgrade the unit in the future.
Fantastic customer service from Joshua as well.
Installed in my 2018 Silverado Custom. I ordered the additional wiring harness and the install took less than thirty minutes. Plug and Play at its simplest. Thank You etrailer.
Exact fit to the controller I ordered it for. I used Deutsch connectors on the controller to easily remove it when I need to work on the truck! Having the spare wires there just in case the connections wouldn't work is nice !
Received this yesterday and was able to install it today. Instructions were very easy to follow and the only problem I had installing it was contorting myself to install the bracket. Once I got the bracket in place the rest was a piece of cake. Went for a test drive as the instructions suggested and did have to tweak it a little but it's doing exactly what I expect it to do. I'll be hauling a John Deere Tractor and wanted to make sure the brakes on the trailer worked.
Works as expected. Prompt service from etrailer!
I installed the Curt gooseneck on my 1993 GMC 2 Wheel Dr. 2500 truck. All the components have tight tolerances. It took me eight hours. With a socket and the wrench. Laying on my back. I did have to cut the wheel well lip about 3/8 of an inch off because I could not get that front angle bar to slide in without hitting it, no way around it unless you lift the bed up and I wasn’t going to do that!!. You have to cut it.instructions do not state that. I’m very happy with the Hitch, it is definitely stout! I did have to make a notch on the outside brackets to go over my airbag bolt. I also had to remove the support bracket on the inside of the frame for the airbag and the crossmember for the spare tire to get the front angled bar in.
Works great no problems
Class iii Draw Tite trailer hitch:
This part was quick and easy to order and I received it sooner than expected. My mechanic said the installation was easily accomplished and looks great on my car. I would not hesitate to order from etrailer again!
My truck was stolen and wrecked. I was able to retrieve the Tekonsha Brake controller from under the Dash board before it was hauled to the salvage yard, but not the wire harness. I was ale to order a replacement harness from eTrailer and reinstall the controller in my new truck. I had no problems at all. Thank you eTrailer for the great support.
These guys are great they had the installation kit it came with everything you need and even had a video for my specific vehicle to install the brake controller and wire in a 7 pin trailer plug
If you don’t have factory brake controller the etbc7 is an amazing kit they have comes with everything I mean everything
This was an easy install on my 2019 GMC truck using the appropriate wiring adapter. Instructions for setting up the control were clear. After a few adjustments my trailer brakes worked as they should. Minor adjustments of the controller are needed from time to time, but overall the controller is reliable. Good value.
The product was easy to install with the help of the F-250 adapter. I followed the direction and the product worked just as it was advertised from etrailer.com. If I had to give the Tekonsha Voyager Trailer Break Controller a star rating from 1-5, I would give it a 4.5.
Works as intended, but the plug on the back of the controller is a loose connection. Sometimes I would go to brake and find that I had no trailer brakes because the controller lost power. After a wiggle it would start to work again. I was able to shave the Molex plug a bit and now I don't have any problems with it.
Purchased this as part of all parts required to convert 1996 Jayco over to electric brakes. Very happy with results. Surprised to see after winter in storage that the battery supply still shows full charge.
Easy installation and seems to be a great product. I also used the harness for my 07 new body Silverado for a easy install. Videos are a great help as well . I will purchase all of my trailer and RV needs from ETrailer from now on.
Do you have a question about this Trailer Brake Controller?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.