Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight behind the dash. Control your braking power with the turn of a dial, with manual override right at your fingertips.
Features:
Specs:
The dash-mounted knob puts control of your trailer's brakes at your fingertips. In addition to offering fast, simple power adjustment and an easily accessible manual override, it has colored LED signals that let you know what the brake controller is doing at a glance.
When you are calibrating the brake controller for the first time, the LED lights will signal your progress. To finish setting up the device, you will need to drive your vehicle in a low-traffic area and brake 20 times or so to let the unit learn its orientation and the direction of travel. If your trailer is connected, the LED light will flash green/blue as it processes the information. If there is no trailer connected, the unit will still calibrate, just without the knob lighting up. The knob will stay blue longer as the calibration process gets closer to being done. When the display turns solid blue, initial calibration is complete. The unit will remain calibrated for the next time that you tow. If recalibration is required, it will happen automatically and without LED indication.
Once the brake controller is activated, you can use the knob to set the maximum amount of power that will be applied to your trailer's brakes. Typically, this power is only readjusted when you experience changing road conditions or if you switch over from a heavy, loaded trailer to a much lighter, empty trailer, or vice versa. To get more power to your brakes, rotate the knob clockwise toward 10. To decrease the power output, rotate it counterclockwise toward 0.
When you apply the tow vehicle's brakes, the knob will change from blue to red to signal that the trailer brakes are being activated. The higher the braking power output, the deeper the red that you will see.
The Tow-Pro Liberty keeps the manual override within easy reach, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just press the control knob. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
Unlike most proportional controllers on the market, the Tow-Pro Liberty has almost no mounting restrictions. It comes in 2 pieces - the main unit and the control knob. Because the only part that you need to be able to access is the control knob, the main unit can be mounted out of sight and out of the way. You don't have to worry about banging your knee on a bulky brake controller or interfering with your vehicle's lower airbags.
The dash-mounted control knob can be installed in any convenient spot that's easy for you to see and access. This can be a blank switch panel, an open spot on your center console, or wherever there's space on your dashboard. You can pick up a universal mounting panel (331-TPSI-001 - sold separately) for a clean, from-the-factory look. Custom-fit panels are available for certain vehicles as well. Before you do any drilling, be sure there's room behind the dash for the entire knob to install, including the part you don't see!
Once you've decided where you want to put the control knob, you'll need to find a good place to install the main unit. Your only restriction is the 3' plug-in cable that has to be able to reach between both the main unit and the control knob. Securely mount the box using screws, double-sided tape, or zip-ties (not included). A mounting kit (RE67FR - sold separately) is also available for the Tow-Pro Liberty. Do not zip-tie the box to wiring or cables that can shift as you drive.
Once you have the controller mounted in your cab, just plug the custom-fit adapter directly into your vehicle's built-in brake control wiring harness. The other end plugs into the brake controller. No hardwiring needed!
Note: If you don't already have a 7-way plug at the back of your vehicle, take a look at our exclusive 7- and 4-way brake controller installation kit (ETBC7 - sold separately).
The Redarc Tow-Pro Liberty Brake Controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Tow-Pro Liberty uses an internal 3-axis accelerometer to sense how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hey everybody, Ryan here at E Trailer. Today on our 2014 Ford E-Series van, we're gonna be showing you how to install the REDARC Tow-Pro Liberty Brake Controller. And, we're gonna be installing this in conjunction with the REDARC Adapter Plug, as well as the Etrailer.com, Universal Brake Controller Install Kit. But before we get to that, why don't we check this out, and make sure that this is gonna be a good brake controller for your situation. When it comes to these E-Series vans, really popular in the service industry, you know, a lot of people use these as work vans, and that, you know, entails usually pulling some trailers around, right You got other equipment or, you know, running from job site to job site, hauling stuff around. And so, you know, when you're pulling that trailer, a lot of 'em are gonna be big enough to have brakes on it.
And, when they have brakes, you're gonna need a way to apply them, and help bring you to a safe stop. And, I feel like, especially with these vans, I mean the factory brakes aren't, you know, this ain't a hot rod. Brakes aren't that great anyway, and then usually you're overloaded, and it's super heavy, and they can just use some help. And so, I feel like it's pretty important to use a brake controller, especially when you're towing. And that's where the REDARC is gonna come into play.
The way this is gonna work is, whenever you're hooked up to your trailer, and you apply the brakes in here, it's going to apply the brakes on the trailer. And what really separates this one from a lot of the others, I'm sure a lot of people have seen a brake controller before, right Kinda like a big box that's mounted on the dash. This one, the main body of it is hidden underneath the dash, out of the way, and all your controls and everything are just done by this button here. It's pretty cool, looks really factory, and clean. On something like this, is it a huge deal Probably not.
But, I do know how things are, you know, how things go. You have this big thing down here, and you got your invoices around, and, you know, stuff piled up all over the place. It's just one more thing that's in your way. And so, it does make sense here. I think it's a good fit for our van.
And, with these, this is a proportional type break controller as well. So, what that means is, it's gonna give us a smooth braking experience. So, the harder you hit the brake in here, the trailer's gonna match it. So, for example, let's say if you're just kind of cruising, hit the stop sign or something, you got your foot halfway on the brake, trailer breaks are gonna do the same thing, right On the other hand, let's say, maybe you're going down the highway, and some road work or something, you gotta come to a pretty quick stop, and you really gotta stand on that brake pedal. The trailer brakes are gonna do the same thing. So, you're gonna be stopping as a whole unit, I guess you could say, and, you know, it's just gonna make it more predictable, and provide you with a more pleasant braking experience. You're not gonna feel that trailer wanting to drag you back, or, you know, kind of push you around. So, anything that can give you a little bit more confidence, to me, is a no brainer. This brake controller is good. I gotta work with those trailers that have one to two axles. It's probably about perfect for this vehicle, I don't really see too many of these pulling a triple axle trailer around, but you're gonna be able to adjust the braking force. So, you have zero to ten, and you can kind of adjust this, you know, depending on your need. So, let's say if you have a smaller trailer with nothing on it, don't need a lot of force, right You can probably get away with like a one, or a two. But then, let's say, if you go to job site, or whatever, and you load it up, and it's super heavy, you know, you can crank it up to seven, eight, nine, ten, whatever. Five being in the middle. So, you know, it might be a good starting point to kind of roll with. But, you know, you do have some adjustability there, which is nice, and you also have a manual override. So, when you push this button down, it's going to apply just the trailer brakes. And, that is good in the event of a sway. So, let's say a trailer starts to kind of, get away from you a little bit, you can push that down, it's going to hit the brakes, and kind of straighten everything back out. Something that I do think is pretty cool, these have the park brake assist feature. So, say if you're at a stop light, and you know, you're sitting there at a red light in a bunch of traffic and stuff. After a little while the trailer brakes will release, it don't really take a ton of effort to hold something stationary, your van can do that without the help of the trailer brakes. And so, by doing that, it's going to help save the life of your trailer brakes as well. You're not gonna be using 'em when it's unnecessary. So, definitely something good to see. And, you know, if it can save you a couple bucks in the long run, definitely ain't gonna hurt anything. Other than that though, at the end of the day, it's a pretty good fit actually. I thought, you know, I really wasn't sure what to think, putting a REDARC in a vehicle like this. But, after seeing it, and seeing how it operates and everything, makes sense. I think think it's a pretty good choice. As far as getting this installed goes, not going to lie, it's a little bit of work, you know, it's just having to wire everything up and route everything. And, it's not really complicated, just time consuming. So, be prepared to spend a little bit of time to get this done. But, if you'd like to see how that's done, feel free to follow along. We'll go ahead and show you how to do it, how to get everything hooked up together now. To begin our installation, we're gonna be here at the back of our van. First thing we need to do, is mount up our 7-way connector, which is this here. And, with this I just used a neutral short bracket to play and put around our hitch, and then connect it to the included bracket, and 7-way connector plug here to it. And, once you got that screwed down, we can get the wires hooked up that come off the back of it. So, here's where the wires come off the back of it are. One of 'em is going to be a 4-way flat type connector, and that's gonna plug into your existing 4-way flat wiring so that'll just plug right into each other. And then, you're gonna have a black wire, a blue wire, and a yellow wire. Yellow wire, we're not gonna be using, that's for our reverse light circuit. So, I just tape that up, just in case we ever do want to use it, but I'm not gonna worry about that one. The blue wire's gonna be our electric brake output. Black wire's going to be our global auxiliary power. So, I took our duplex wiring here, the big roll of wire that we get, strip back the insulation on each end, and use buck connectors to pair the two wires together. Then that leaves a white wire coming out of our 7-way connector. That's gonna be a ground wire. And, with that one, we simply just use the provided self tapping screw to run that up into the frame rail, to provide us with the necessary ground there. So, once all that's done, you know, obviously you can come back, tape everything up, kind of secure it and whatnot, but once that's done, you can take your duplex wiring, and start to run this towards the front of our vehicle. So, I went ahead, got our wiring ran up towards the front of our van, and I just ran it along our frame rail here, doing your best to avoid any hot or moving parts. And, you can just secure it along the way using some of these zip ties. Well, essentially just a straight shot, more or less, all way up to the front. See kinda where it comes out there And, it goes just on top of that heat shield, obviously away from it, but above it. It comes up here, then goes up into the engine compartment. And, the way I got it up there, I dropped a piece of tubing down from the top, or you can use like a coat hanger, or something along them lines, tape your wire to it, go back up top, and pull it up into position. So now, in the engine compartment, power wire comes right up, and then I have it separated. So obviously, you cut back that gray sheathing, and you got a white and a black wire. White wire runs over towards the driver's side, we'll get to that in a moment. But, for now, the black wire, that's gonna get ran to a breaker, which I have mounted up right here. You'll have a 20 amp breaker, which is this one. And then, a 40 amp breaker, which is this one. The wire that's coming up from the bottom of our vehicle, that's going to go to the 40 amp breaker, the silver post. So, crimp on a small ring terminal over the silver post, tighten it up with a 10 millimeter. The 40 amp breaker's gold post you're just gonna take maybe eight inches of that wire, crimp on a small ring terminal, a large ring terminal on the other end, tighten it down on the breaker, and then this, eventually, is gonna get hooked up to a power supply right here, but I want to get everything else hooked up first. As far as the 20 amp breaker goes, the gold terminal, you're gonna do the same thing as the 40 amp. Small piece, large ring terminal, small ring terminal, this will go to power as well. Then, the wire coming off of the 20 amp breaker, coming off of the silver post, that's gonna need to get routed inside of our van, along with that white wire. So, let's go ahead and take a look at how we did that now. So, here's our wires running into the firewall inside of our van. If you move the coolant reservoir out of the way, there's just a few bolts holding in, pop them out, then it slides right on out of the way. You can drill a hole into the firewall, which obviously pay attention to where you're drilling. You don't want to drill through the backside of it, and drill into your computer, or harness, or something like that. So, pay attention what you're doing. And then, I used a rubber grommet to pop in there, to keep the wires from rubbing up on bare metal. And, once I had that complete, I was able to take our wires and simply fish 'em inside of the van. So, inside of the vehicle now, underneath the dash, this is where our wiring comes through. And, this is gonna get routed, essentially, to the center console, and up there's a small compartment, that's gonna be right above your radio. And so, if you just kind of feed the wires along here, and up towards the top of the dash, you can show you the little compartment, you can pull out to reach down in there and get your wires. So, this is the compartment I was talking about. And, with this, it just essentially pops out. Sometimes you can take a flathead, or a butter knife, or a sharp tail tool, pop behind there, release those clips. This'll pop out, and then you're gonna have this clip, or I'm sorry, this connector plug, which is our plug for our brake controller, which we will be using that in a moment. But, here's our two wires. So, like I said, I was able to reach down in here and grab them, pull 'em up. And, these are gonna get connected to, your brake controller plug, which at this point, you know, with the exception of hooking up our power wires, at this point, this is where, you know, the install more or less stops for the Universal Brake Controller Install Kit. But, with that said, obviously you're not gonna get to this point and then not finish hooking up your brake controller, right So from here, this is gonna be very similar regardless on what type of brake controller you plan on using. But, what you're gonna do, is take your brake controller adapter plug. So, they actually make 'em specific for our vehicle here. And, with this particular one, it just plugs in to that. And, the reason ETBC7 our kit there, was because from the factory, this is only providing us with a ground and a brake light, stop light switch, brake signal, more or less. We didn't have power, or brake controller output, that's why we had to run all these wires. Sometimes you can use, find at least power, which would be this black wire here. But, you can look in the fuse block, you might have to pop fuse in, sometimes it's not slotted. To be able to do that, and then if you're still gonna be running one wire anyway, you might as well just do 'em both. There's really no difference in labor. So, with that said, since obviously, these aren't getting plugged in to our other end there, I have the end there, our blue wire, and our black wire, from this end, hooked up to our brake controller install kit wire. So, black goes to black for power, and blue goes to white for electric brake output. The other wires coming off, the red and the white one, can utilize the factory plug there. Plug that in, white will be your ground, red will be the brake signal. So, with that all done now, what we can do is find a spot and start to set up our brake controller. So, what we did was mount up our brake controller box. It's a little tricky to see, but it's this red piece around here, and there's a big bracket. This is under the dash by the way, that the panel literally just pops out, you pop this off. But, the way this works is it went around this bracket, and around this big wire loom, and zip tied it up, and it is not going anywhere, that thing is solid. So, that leaves you with this phone. It's kinda like a phone, old phone cable, old phone cord. One end of it plugs into, you know, the side of your brake controller. And then, this end, it's gonna plug into the switch, or the knob that we gotta mount up. So, I feel like the knob, a good place to mount that is somewhere in this area. I'll figure that out and we'll kind of go from there. So, here's where I mounted up our button. I think it turned out really well. Behind here, there's actually quite a bit of space, especially with that lower panel down still. You just use the plastic trim ring as a guide more or less, you drill out a larger hole, drill out a smaller hole, put the trim ring on, tighten this down, and then just pop your button on there. And, you know, obviously you wanna line the button up accordingly. So that way, you know, in the middle is in the middle, halfway through. So, I've done that, but now that everything's hooked up, we'll go underneath the hood, connect our power wires, and then we can calibrate, and check everything. Under the hood, went ahead and got these wires hooked on up. And, I just use this power supply stud here, remove the nut with a 10 millimeter, put these on over it, and tighten it back down. So, I went ahead, hooked up to a test box, and that's just simulating a trailer. You can always just hook up to your trailer as well. But, we'll see if this is working. So, right now it's flashing, which means it needs calibrated. Not really a big deal, you just drive around, and apply the brakes as you normally would. I believe it's easy, you don't even have to have the trailer hooked up either, just drive around like normal. Once it turns solid you know it's calibrated, but for now we can still test at least, make sure it's working. So, what I'll do is apply the brake pedal, and we can look at our test box, and make sure that power is being sent back. So, whenever I'm pushing our brake pedal down, we can see that we do have a brake output, and our brake controller is functioning. And, that'll finish up our look at, and our installation of the REDARC Tow-Pro Liberty Brake Controller, on our 2014 Ford E-Series van..
Average Customer Rating: 5.0 out of 5 stars (2 Customer Reviews)
Mount the control knob of this proportional brake controller on your dash for a factory look, and install the main unit out of sight behind the dash. Control your braking power with the turn of a dial, with manual override right at your fingertips.The hardest part was getting the zip ties tightened around the module without completely removing the trim under the steering wheel. I chose near the shifter for my location so it’s easy to reach but still out of the way.
Works great! No more readjusting between hi way and Campground driving. Looks great. Straight forward instruction for installation.
This thing is so much better than the old controller I used to use. I like that it lets the break off after you stop moving even if you have your foot on the petal. Smooth breaking response all together. Plus, I was able to install the knob in an unused switch blank in my 2020 Pilot. You do have to be a little crafty to get it to fit there but it is possible.
I was surprised how nice this brake controller is - clean install with the unit up under the dash. I installed the knob in one of the 'blanks' in the dash for a really clean look. No banging knees on older-style controllers under the dash. Thanks!
This is a great product to install Works fantastic in my 2023 Jeep Grand Cherokee Limited the remote switch you can put just about anywhere. I like how you don't have the big old bulky brake controller under your dash.
This is my second trailer brake controller from Redarc with this style. Neither of the vehicles I installed them in came prewired from the factory (2019 Subaru Crosstrek and 1999 Isuzu Amigo). The hardest part of installation for me is locating a place to put the "knob" that is easy to access but out of the way and most importantly doesn't require me to drill holes into hard parts of my vehicles. In both installs I managed to get the knob installed into a blank switch knockout. I run the power directly to the battery and have not had any problems with it turning itself on when needed or causing the battery to drain. This is by far the best looking trailer brake controller on the market that isn't factory installed
I purchased the Redarc Liberty brake controller because I couldn’t find a place to mount my Tekonsha where I wouldn’t bash a knee or shin on it or cover an airbag.
So far, I’m very happy with the Redarc Liberty brake controller; although, I haven’t used it for towing yet, and I’m not sure it is operating properly. Apparently, I should have blue lights while it is learning which way the control unit is oriented but I don’t have blue lights.
Anyway, let me share information on the installation. I purchased the wiring harness for my vehicle, which I highly recommend as it was same cost as the universal harness, and a big time saver. I did not buy the blank switch panel for the switch installation as another reviewer stated he was able to modify the original switch blank. Big mistake, I highly recommend buying the appropriate switch panel for your vehicle. My Toyota blank switch panel was excessively complicated so I had to saw and melt a pile of plastic (see the picture) out of it without damaging the visible portion or the clips which hold it in.
Finding a suitable location to secure the controller up under the dash is a challenge with modern cars. After removing two pieces of plastic trim, I did manage to pull the panel below the steering column far enough out to complete the install. The unit it does look good. Very clean.
We’ll be towing the big trailer next week so I hope it works.
Being new to towing a larger trailer requires research. After doing a lot of it, both through user reviews and manufacturer websites, we landed on the Rearc Liberty Brake Controller for our Tacoma. We have just over 1000 miles towing with this unit. It has performed extremely well. Towing for us includes city, highway, mountains, and even off-road to access our mountain home. Installation was straight forward and the ability to install the controller in virtually any position is an added bonus. I was able to install the dash knob in a blank panel giving the Tacoma a factory appearance, and controller located under drivers seat. I installed this unit on a non tow package Tacoma, so wiring was a bit intimidating at first. But using etrailer’s web site as a reference had everything operational in a couple afternoons. Great product so far and we look for years of use. Highly recommend.
Great controller and helpful service! Take your time installing the control switch in a convenient place. It's small but works well. I love the easy use of manually applying the trailer brakes by pushing the switch. Mounting the control module in a solid place is required. I bolted it to a dash brace and it works well.
The controller looks and works great. The colors are very easy to see what the controller is doing. No led colors are displayed when there is not a trailer plug in, so it almost disappears on the dash.
Reason I only gave 4 stars out of 5, like others said, the universal harness should have come with it like it does with the Elite. My truck is older so I needed the universal harness. You should only have to buy one if it is a direct plug and play for newer trucks.
Haven’t had any issues with the brake control after towing for a year. It’s been a great replacement for the curt Bluetooth controller which didn’t last 2 months because it’s made with cheap plastic and stuck out so far I backed my trailer into it when parking.
The brake controller was not difficult to install.
I like the fact of controller is in dash area of vehicle with just one control knob shown. Shipping was fast and all items are as described.
Thank you
Installed this in my 4runner that I use to haul several thousand pounds of metal boxes on an aluminum heavy variant tilt deck trailer. Install was fast and easy, the main unit is small and is easily tucked up under the dash. I drilled one small hole and placed the small lighted selector (small blue light) on the key side of the steering wheel area (see pics) and looks like it came factory from the truck. Its sasy to adjust and robust enough that it wont move settings on its own, even in rough off road conditions that a 2WD vehicle cant go. Ive had other controllers in the past but am super happy that I had lucked out and found this proportional one from Redrac with the dash knob.
Installation was very easy, simple, and clean. Looks very nice. I am very disappointed that nobody makes a switch insert panel for Honda or pretty much anything but Toyota. I haven’t programmed it yet but it looks fairly simple.
Very clean option for a proportional trailer brake controller. Nothing to knock your knees on and easy to access for extra braking as I mounted it in the dash of my E350.
A major upgrade from the old brake controller. Great price and quick delivery
I had a cheap brake controller made by CURT. It lacked the manual on it and it was causing my brakes to lock up on the left side of my camper. We found this out going down a mountain pass so it was a little alarming. This brake controller is amazing and I love it so much. Being able to tune it activated and have constant feedback on whether it's working or not is awesome. I highly recommend this. It's perfect for me.
This review includes the following items: Item #RED69FR - Wiring Harness, 30A Breaker kit and Item # ETBC7 Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat and Item #RED24FR Controller. I wanted to be sure I had everything. A local place Custom Coach on Pulaski Hwy, Baltimore did a fantastic job on the install, Sorry I can't remember the techs name. I have a 2018 Kia Sorento SX V6, AWD with 4 pin Tow Pkg. car rated for 5k/500# load. Trailer is a 2022 Palomino Real Lite RL-186. I've logged 2 trips so far 1 to NYS mostly highway and to Cass, West Virginia area. The controller adapted quickly, I went to a '5' to a '4' setting even in the mountains it was smooth no jerking. The one picture shows installation ubder the dash totally out of the way. It works great!
Expedited shipping was super fast with no problems. I installed the unit myself and it was fairly simple. I recommend getting the exact fitting wire harness (huge time saver) and I’d recommend getting and exact fit knock out to install the dial in. (Another big time saver). I drilled a hole in my own blank or knock out thingy and I’m pleased with it but it took a little time. I’ve got a 2010 Honda Pilot. Funny thing, after rushing to install the brake controller, our trailer had to go in for repairs before we even completed the transaction. It will be another month before I actually use the brake controller.
Install was quick and easy. The only thing that gave me grief was that darn "Trailer Brake Warning Fault" message that kept displaying on my message information display on dash. After troubleshooting for several days and calling etrailer for assistance with no solution, I tried calling Redarc with the included state-side tech support. The number puts you in touch with an Ausie down under so you have to adjust your call with thier time zone. Turns out, and VERY IMPORTANT,if you are replacing an OEM Trailer Brake Controller already installed in truck. The TBC Controller Brake Module has to be deactivated to make the fault go away. Truck still think it has a TBC and is looking for it. I used Forscan software to deactivated it through the OBDII port.
I love the features of the RedArc Tow Pro Liberty and its ease of use..
Works great, install instructions way too small for me to see, so I watched video on YouTube on how to install. If not for the videos I couldn’t have installed it!
The controller and dash knob are solid and nicely crafted. Both are made to be easy to install. The dash knob works great and is simple and easy to use. The manual is well written, and has detailed and very useful information. Be sure to get the REDARC Tow-Pro Harness (TPH-025), too, which is needed to complete the hookup of the controller.
After 9 camping trips with my trailer, the brake system is working well.
The installation is super simple with its multi-directional mounting system. Great!
Great product, shipped fast and I could not be happier with the "from the factory" appearance of the installation. I painted the embossed letters in the switch mounting plate so it would match the other switches. The brake controller works well and it really looks great.
Do you have a question about this Trailer Brake Controller?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.