To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Retractable tonneau for your vehicle has aluminum slats and a vinyl top layer that combine the strength and security of a hard cover and seamless look of a soft cover. It locks at any point along the rails, and it retracts easily with a handle.
Features:
Specs:
Retractable Cover with Built-In Pull Strap
The original JackRabbit retracts with the turn of a handle. The handle - located on the key latch at the tailgate end of the cover - activates a heavy-duty tension spring. This spring automatically retracts the cover into the canister at the bulkhead of your truck bed. A built-in pull strap helps you extend the cover over your bed. As you pull, the tonneau will engage the side rails at 12" intervals. You can stop the cover at these designated intervals or you can use the key latch to lock the cover at any point along the side rails.
This feature enables you to carry tall or long items that overlap your tailgate while still covering cargo, such as a toolbox, stored closer to the bulkhead of the truck.
A hook-and-loop fastener strip is included to secure the pull strap up and off of your bed floor. You can also use the rear plate of the tonneau cover to pull it closed.
Angled Canister
The cover retracts into a compact, angled canister located at the front of your truck bed. This canister protects the retracted cover from the elements, and with the cover stored in the canister you'll have unrestricted visibility out of your rear window. The angled design of the canister also allows for maximum clearance for your tools and cargo so there is no need to remove the cover to haul cargo.
Water Management System
The JackRabbit rails feature a water management system that channels excess water into the canister. This prevents water from getting into your bed or freezing in your tonneau cover rails during cold temperatures. Drain tubes attached to the bottom of the canister remove water through the OE drain holes in the floor of your truck bed.
Flush-Mount Design
The black powder-coated side rails mount level with your truck bed rails for a flush appearance. This flush-mount design is aerodynamic to reduce wind drag, and it helps to improve gas mileage when the cover is closed.
Even with the flush-mount design, the cover fits over most fifth-wheel trailer hitches. Note: The highest point of the fifth-wheel hitch must be at least 2" below the bed rails.
Stylish and Heavy-Duty Construction
The JackRabbit deck is constructed of a vinyl top layer bonded to heavy-duty aluminum slats. This ArmorTek deck looks like a soft tonneau cover with no visible seams, but has the strength and security of a hard tonneau cover. A large seal at the rear of the bed closes the gap between the cover and tailgate to create a barrier to prevent water from entering the truck bed.
Security
The Jackrabbit provides excellent protection for your cargo when used in conjunction with a closed and locked tailgate. The heavy-gauge aluminum panels are better at preventing theft when compared with soft covers that can be cut or punctured with a knife. The panels are also more effective at preventing theft than tri-fold hard tonneau covers because the panels cannot be pried open at any point along the rails.
No-Drill Installation
To install the cover, set the canister in your truck bed and support it with a box or other sturdy object. Slide the cover side rails into the canister until they are fully seated in the rail grips while also threading the cover into the channels in the rails. Secure the rails to the canister with bolts and washers.
Secure the rails to your truck bed side rails using 2 clamps per side. Slide the clamp onto the rail, flip the pivot arm up so it is under the bed rail lip, and tighten the clamp in place. Shims are included for trucks with tapered beds.
Mount the top cover plate to the canister with the included hardware. Attach the drain tubes to the canister and route each tube out of the OEM drain holes in the floor of your bed.
To hold the pull strap off the floor of your truck bed, apply the adhesive hook-and-loop fastener strip onto the underside of a rail at your desired location.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today we are going to be taking a look at the Pace Edwards line of Jackrabbit Tonneau covers. The Pace Edwards Jackrabbit is a great way to protect your truck bed and your gear. It's made with Armor Tech padding that's laminated to aluminum ridged panels so it gives you hard cover security with a soft cover look. It's easy to operate. It features a one latch release system. We'll drop down our tailgate, we'll be sure and hold on to our pull strap, turn the latch to the left, and the tension springs roll it up for us.
It has multiple catches along the rails. This is great for partial loads. The rear plate doubles as a handle and it can be locked in any position, two keys are included.When used in conjunction with a locking tailgate, the whole bed is secure. It's a no-drill application. The rails easily clamp on in place.
The clamps themselves have a unique two-piece rail design, which allows them to fit tighter than your traditional style clamps. The whole thing has a flush-mounted low-profile design. The canister sits inside your truck bed, about 11 and a half inches. The rails sit inside your truck bed, about two inches. It features a large tailgate seal that sandwiches between to prevent water from getting inside.
The whole thing is weather resistant and since it is made out of aluminum, it's going to resist rust and corrosion. That's going to complete our look at the Pace Edwards line of Jackrabbit Tonneau covers.
Average Customer Rating: 4.5 out of 5 stars (10 Customer Reviews)
Retractable tonneau for your vehicle has aluminum slats and a vinyl top layer that combine the strength and security of a hard cover and seamless look of a soft cover. It locks at any point along the rails, and it retracts easily with a handle.Jackrabbit has been installed for a week now. Simple installation took less than an hour. Looks good and operates well. Having rained, it seems I'll need to add some weather stripping in some areas. Rails and head box arrived on different days. Side rails arrived with a 3/4" long gouge on the top of the drivers side which was disappointing. Overall happy with the purchase. 765379
We love our Tonneau Cover! It has been a practical solution for keeping items dry and safe when we travel. We have also had a number of fellow campers and travelers admire how it looks and how convenient it is to use. We would highly recommend this type of tonneau cover. 666851
Review from a similar JackRabbit in Tonneau Covers
4 stars, good quality product and packaging. Installed by myself in 1 hour. Fit and finish are very high quality. However...the drain hoses for the canister are both 3" too short to reach the drain holes in the bed. And even if they were long enough, the hoses are too big to fit through the drain holes. So now I have to bodge together some sort of clamped-on extension so the canister drains properly. 927289
Review from a similar JackRabbit in Tonneau Covers
First WATCH the install video completely to understand the way to properly install (I didn't) After much frustration I stopped and watched the video and installed the cover in about 15 minutes with the help of my daughter. The finished product looks great and it functions as expected. Save the frustration and watch the install video (you tube) from etrailer expert. 773066
Review from a similar JackRabbit in Tonneau Covers
I should have followed the advice of using the box it came in to support it in the bed. I used a couple of coolers that were a couple of inches taller. That made aligning the rails with the canister just about impossible. After I switched to the box, it was relatively easy. The cover fits my 2019 F350 long bed fine, but the "kickstands" for the rear brackets don't really fit. Not enough room between side of the bed and rear brackets. I got them in there, but I may need to attach a small bracket for the kickstand pad to push against. It's suppose to push at a 90 degree angle or it slips off. We'll see. 763113
Review from a similar JackRabbit in Tonneau Covers
Outstanding product and customer service! Purchased a year ago and I have been putting it to work ever since. The initial shipment was quick and on time. 750278
Review from a similar JackRabbit in Tonneau Covers
Product fits great and adds super prote ction! 735239
Review from a similar JackRabbit in Tonneau Covers
After installing it, it looks like it will work for what I need. 610251
Review from a similar JackRabbit in Tonneau Covers
Excited about my tonneau! Here's a pic. Love it, thanks much. 509424
Review from a similar JackRabbit in Tonneau Covers
Just received my q25 hitch, one end of the box was missing and the other was torn up pretty bad, the two side pieces are scratched up a little, I'll touch them up with some black paint, other than that it looks like it will work good. 490904
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.