To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Weather-resistant, roll-up cover keeps the gear in your truck bed secure and dry. Rolls up quickly by hand for full access to your truck bed. Aluminum slats keep cover tight and help prevent break in. Requires no drilling to install.
Features:
Specs:
Get the advantages of both a hard tonneau cover and a soft tonneau cover for your vehicle with the Revolver X4s. This hybrid tonneau likely has an identity crisis. It's built like a hard cover, but it looks and acts like a soft cover. With the Revolver X4s, you get the strength, durability, and security of a hard tonneau and the sleek look and convenience of a soft, roll-up tonneau - all while protecting your truck bed and cargo and helping to improve your fuel mileage.
The X4s has the features of the original Revolver X4 with upgrades including a matte black aluminum underbody, integrated safety slat caps, rear corner caps, and an integrated bulkhead seal.
The secret to the Revolver X4s's versatility is the aluminum slats on the underside of the cover that make it strong, seamless, and flexible. These individual, hinged slats give the cover its rugged body, while also allowing enough flexibility for the cover to be rolled up. Atop the slats is a tough, 1-piece vinyl layer that adds to the tonneau's sleek look and overall durability while also keeping the slats perfectly aligned. As a result, the Revolver X4s will roll up evenly every time, unlike ordinary soft vinyl covers that can get lopsided as you maneuver them.
Unlike other tonneau covers that sit 1/2" or more above your truck bed rails, the Revolver X4s sits nearly flush with your rails for a clean, ultra-sleek look.
The Revolver X4s gives you full use of your truck bed in a matter of seconds - just roll up the cover and secure it behind the cab. As a result, you can tote around all your gear without having to remove the tonneau. And because the Revolver X4s mounts inside your truck bed rails, you can still use your truck bed stake pockets to mount accessories like tie-down anchors.
The Revolver X4s is simple to operate. Following installation, just roll the cover out and press down on the rearmost slat at the tailgate to secure the tonneau in place. The built-in latches not only lock down the back end of the tonneau, but they also fasten the sides of the Revolver X4s along the length of the frame rails. The rail tooth runs the entire length of each frame rail. It rotates downward to lock the side rail into the sides of the cover.
When the cover is rolled out and the rear slat is pressed down at the tailgate, the latches on both sides engage. When this happens, the integrated teeth pivot down and rest on top of each slat of the rolled-out cover. Closing the rear slat effectively pins the cover to the rails, ensuring that the cover stays closed from front to back. It's that simple - no Velcro to seal or snaps to wrestle with. When your tailgate is closed and locked, no one will be able to get through the cover, thereby safeguarding your truck bed and its contents. The cover automatically secures as the locking levers at the tailgate engage. These sturdy levers have reinforced gussets that give them added strength and durability. And they will never need adjustment.
To roll up the cover, unlatch the rear slat by dropping the tailgate and pulling either of the 2 release cords located along the bottom corners of the slat's housing. Either cord will release both of the latches so that you can raise the rear slat. When the latches are disengaged, the teeth roll back into the frame rails, releasing the sides of the cover so that you can easily roll it up. Just fold the rear slat over and roll up the cover the rest of the way.
Then secure the tonneau behind the cab with built-in nylon straps and sturdy plastic buckles. These straps help to keep the bundled tonneau from contacting your cab while you drive. And 4 rubber bumpers act as cushioned barriers between the cover and your truck cab.
The Revolver X4s's rugged aluminum and vinyl construction makes it an ideal match for your truck, no matter what you do while at work or play. This cover is strong enough to hold up to 400 lbs of evenly distributed weight when it's rolled out. The 1/4" thick, aircraft-grade aluminum slats are covered with a matte black vinyl skin for superior resistance to impacts, UV rays, and weather. This skin is what gives the tonneau its soft, sleek look. While the Revolver X4s may look like a soft cover, its aluminum skeleton provides exceptional security because it cannot be cut through in the same way that a standard soft vinyl cover can be.
Felt strips on the underside of the tonneau help to keep the slats from scuffing the vinyl top as you roll up the cover. The soft felt also shields your hands when the cover has gotten hot or cold. And rubber strips overlay your truck's side rails, cab rail, and tailgate, creating a seal that helps to conceal any gaps and works to prevent water from seeping in.
Easy, No-Drill Installation
Installing the Revolver X4s is simple. All you need is a wrench, and you don't have to do any drilling. The tonneau's frame rails clamp to the inside of your truck bed side rails to create a base for the cover. The included bolts secure the front hinge rail to the frame rails at the cab.
Slotted brackets at the ends of the tonneau side rails allow the bolts to shift in case you need to adjust the cover to achieve a snug fit. These brackets ensure proper alignment of the tonneau frame on your truck bed side rails. This eliminates trial and error in installing your rails - you won't have to put them on and then take them off again to get the correct fit. Pre-installed shims and spacers also help to ensure that the Revolver X4s rails are installed squarely on your truck bed.
Average Customer Rating: 4.4 out of 5 stars (28 Customer Reviews)
Weather-resistant, roll-up cover keeps the gear in your truck bed secure and dry. Rolls up quickly by hand for full access to your truck bed. Aluminum slats keep cover tight and help prevent break in. Requires no drilling to install.The original cover was improperly sized from the factory (direct shipment from BAK due to backorder). etrailer, as usual, went above and beyond to get me the correct fitting cover. The new cover fits perfectly and looks great on my truck. Hopefully it will last, though I worry about the quality considering BAK did not notice they sent me a cover with the wrong dimensions originally. Giving 4 stars due to poor QA from the factory on the original shipment.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Fit is a little tight at the latch end even after removing shims, but overall very nice and sturdy. There was some minor damage to the product when it arrived, but nothing that impacted its function or outward appearance. Much nicer than the Revolver (old name) that I had on my last truck.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
I was able to install this cover, with help from a friend, on my 2015 Chevy Silverado 6.5' bed in about 45 minutes. Everything aligned perfectly, it closes smooth, seals well, kept out the rain from a torrential rainstorm the next day. The matte finish on the vinyl matches the plastic on my truck, and doesn't look cheap like most other covers. I love the low profile between the rails look, the truck looks like their isn't a cover on until you get above the bedrail. Totally happy with this product!
Patrick V - 05/27/2019
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Excellent tonneau cover! Super easy to install, and open/close as needed. The only issue that keeps it from the fifth star is the plastic clips on the strap that hold the cover in the rolled up position are designed backwards in my opinion. Definitely a minor issue, but it could be easily remedied to work muck better. This cover works great with the Thule TracRac SR ladder rack.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
This is the wrong cover for anyone with a long bed and a fifth wheel. The weight of the cover when rolled up for an extended time causes the cover to break. BAK was outstanding and replaced it with a Flip BAK cover at no cost.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Overall good system. The one issue I have is the 2 plastic snap on pieces at the tail gate have both come off and are no where to be found. Without those pieces water get inside the bed when it pools up. I should have super glued them in vs relying on the snap in method.
Brooke M - 06/27/2022Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
The Revolver looks clean and is very secure. I get compliments on it all the time! Been installed for just over a year now and still looks great!
Customer service is top notch!!
I love the videos guys. They answer so many questions and help you decide. Thank you for taking the time to make all of them. Smartest thing ever!!!
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
I have a 05 Dodge Ram 2500 short bed. This is the only cover that I could find that works with my track Rack. It is a great combination
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
2021 Toyota Tacoma. I really like this cover. The installation was pretty straightforward, the instructions are good but the video really helped. Where the cover meets the tailgate there are plastic pieces that cover and finish the edges on both sides. These came off when I closed the cover. I ended up using a flexible glue to make sure they stayed in place. So far so good. The bed of the Tacoma is not water tight so even with the cover on there will still be some water get in. The cover even got Big Brother approval.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Fantastic engineering, and great looking. Was straightforward to install following included instructions. Very happy with this product so far on my 2013 Silverado.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Installed myself in less than an hour and a half. Helpful video for installation. Quality fit and finish. Matte finish matches side and rear of Ridgeline bed exactly for a seamless look. Subject to torrential rains (Florida) , minimal water intrusion. Suggest lite lubrication of retaining brackets to side rails for easier positioning during installation.
Charlie R - 08/18/2020 Charlie R - 08/21/2020Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
After owning and using this tonneau cover for a year, I LOVE IT. It works great with my fifth wheel hitch (RAM 2500 Mega Cab with a 6' bed with Rhino liner sprayed-in) by rolling out of the way. The only minor issue is that it does block the view a bit when backing up to the camper or trailer. But that's not a manufacturer flaw. We've used it to cover luggage on long distance trips in the truck and water does drip in, but it's controlled and minimal so it's not an issue at all. Install was easy-peasy. Black color has held up well in the sun over the last year. Highly recommend!
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
I saw mixed reviews but took the chance and I regret it! The felt on the inside came off and has made the cover hard to use ripped off only a few short months after I got it. The company sent replacement felt which is going to be a major pain to replace. It also only does an “ok” job at keeping out water. It’s not a single hand open using the wire like it says. Only advantages is that it rolls up to keep majority of the bed open and you can set some stuff on it.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
I like that it has the aluminum to keep it a little sturdier than other roll up covers. But I do not like that it leaks by the tailgate and at the top corners close to the cab.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
The top is very nice looking and the installation was very easy. The product was engineered well to fit my truck beautifully.
Two issues though...it came with some minor scratches and it leaks at the front corners.
Rachael H - 04/12/2018Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Best roll up tonneau cover on the market. Pairs perfectly with my Thule ladder rack.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Love the cover, secure, strong and good looking . Top Quality. I live in Washington state where we get rain most of the time. And my bed of the truck stays dry. Even when I go through a car wash only a few drops somehow find its way in. When I drive around to look at other covers I fell great with my choice.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
The cover was easy to install. It took my wife and me around an hour to install. I like the convenience of being able to easily roll it up out of the way when we need access to the bead, yet knowing that items stored in the bed are secure when the cover is rolled out.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
It was easy ti install. I had it for a year and it still looks new. The only thing it needs is a seal for the tail gate. But it only leaks when seating still the rain blowing at the back of the truck or going thru a car wash. Would recommend it, the leak has never given me a problem.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
I love this cover! It is well made and I was able to install it in 20 minutes. After a year it looks brand new and I've had no issues with it.
Thanks Lisa D for recommending this cover!
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Fits great after I figured out that I needed some shims. It nice not to have to worry about items in the back of the truck.
Mike - 04/11/2020Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
The cover has held up well, I would purchase again. A couple small items could be updated from the factory but overall its a nice cover.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
love the cover no leaks easy to roll up when you have big loads easy to roll back and fasten. love it.
Review from a similar BAK Revolver X4 Tonneau Cover in Tonneau Covers
Still covers the bed, no problems after a year
Do you have a question about this Tonneau Cover?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.