Kwikee 34 Series Electric RV 2-Step - Motor, Control, Switch - 26" x 8" Bolt Pattern

Kwikee RV and Camper Steps - LC3722862

Powered RV entry steps with 31-1/2" mounting plate automatically open and close with your RV door. Motor and control unit extend and retract steps. Switch kit lets you override step extension. Amber light illuminates when steps extend.

Features:

• Electric RV steps automatically extend when you open the door and retract when you close the door
  • Motor, control unit, switch kit, and light included
• Integrated motor automatically retracts steps if they strike an obstacle during extension
  • Features a fully-sealed gearbox with brass ball bearings and linkage
• Control unit connects steps and step light to the opening and closing of the RV door
  • Ignition override safety feature retracts steps when the vehicle's engine is started
• Switch kit allows you to override automatic extension and lock steps in extended position
  • Mounts to door and doorframe and stops retraction when they touch
  • Keeps the steps out when parked, whether the door is open or closed
• Amber incandescent light illuminates steps to make them easy to see at night
• Non-slip tread on step surface ensures solid footing
  • Reflective strips provide additional visibility
• Sturdy, powder coated steel construction with weatherproof wiring withstands the elements
  • Solid steel drive rods and stainless steel bushings provide additional durability
  • Air pressed rivets at pivot points ensure long-term strength
• Simple installation with existing mounting holes and wiring harness
  • Hardware sold separately
• Made in the USA

Specs:

• Entry height: 13-1/2"
  • Height when folded: 7-7/8" tall
• Mounting plate dimensions: 31-1/2" wide x 11-3/8" deep
• Bolt pattern: 26" wide x 8" deep
• Step dimensions: 30" wide x 10-1/4" deep
• Drop/Rise: 7"
• Voltage:
  • Motor: 12V
  • Switch kit: 250V
• Control unit amperage: 10A
• Light bulb type: C193, incandescent
• Control unit wire gauge:
  • Green: 12 AWG
  • Purple: 16 AWG
• Weight capacity: 300 lbs
• 1-Year warranty

Kwikee electric RV entry steps provide an effortless, convenient way to enter and exit your RV. The steps are wired to your RV's door and feature an automatic extension, unfolding when the door opens and retracting when it closes. This differentiates the steps from the alternate manual pull-out steps.

Motor, Gearbox, Linkage, Control Unit, and Switch Kit

The updated Kwikee steps manufactured since 1999 require the integrated motor, gearbox, and linkage (IMGL) setup to power the steps. The motor provides the power, the gearbox turns the linkage arm, and the linkage pushes the steps out and pulls them back in when rotated by the gearbox.

The motor powers the control unit, which senses when the RV door opens and closes, extending and retracting the steps in tandem. The switch kit - consisting of 2 magnetic sensor pieces that mount to the door and doorframe, and 1 rocker switch - works with the control unit. When the sensor pieces come into contact with each other, the steps are pushed in or pulled out. You can override the automatic retraction with the rocker switch. This will lock the steps in the extended position.

The included 4-way plug fits into the existing wiring harness on your RV. Most vehicles should having this wiring already set up. In the event that your RV is missing the wiring, a 4-way pigtail is included to help you hardwire the unit to your RV.

Safety Features

The Kwikee steps include several safety features in an effort to prevent injury to you or your passengers and damage to the RV steps. If an obstruction is detected while extending, the steps will halt and retract back into the stowed position. The steps will also retract when you turn on the vehicles ignition, even if the automatic retraction override has been activated, in case you forget to stow them before driving away.

Installation

Electric steps are typically installed on RVs and some travel trailers. The electric steps from Kwikee install and fold up underneath the camper for simple storage. To ensure you choose the correct size for your application, there are a few measurements you will need to take.

Will Kwikee Electric Steps Work For Me?

The Kwikee electric steps attach to the underside of the camper chassis, directly beneath the doorway. To decide which size you'll need, locate the space available underneath your camper that lines up with the doorframe, and measure the width and depth. You will need a mounting space that is at least 31-1/2" wide and 11-3/8" deep.

If it turns out you have more or less space beneath your doorway, there are other bracket sizes available ranging from 24-1/2" wide to 36-3/4" wide. A full list of the available steps is listed below.

Outriggers - metal brackets that act as an extension (LC301704 - sold separately) - may be needed for installation depending on the model of your original stairs. These provide extra length if the old steps are longer or wider than the new.

Once you know where the mounting bracket will go and what size mounting bracket you need, that spot will be used as the "mounting point" to determine how many steps you will need.

How Many Steps Do I Need?

To decide on how many steps you'll need, measure from the mounting point to the ground. This is called the entry height. The entry height should roughly match the height of the steps when they're fully extended, plus 6" to 8" to account for the drop from the bottom step to the ground. This measurement will also tell you how many steps you need.

The chart below displays mounting bracket widths in the first column and entry height measurements in the second column. The third column shows the corresponding part numbers. Use the mounting bracket width and entry height measurements you took to determine which part number will fit your RV. Choose the bracket size that is closest to your measurements without going over.

This page's step assembly is in bold text.

*Motor, control unit, and switch kit included

**Motor and control unit included

***Motor and switch kit included

****Motor only

How Do I Install the Steps?

To install the steps:

1. Hook up the steps to power to verify that all components are in working order.
2. Make sure the camper is level on flat ground.
3. Lift the steps into the mounting space and prop into place.
4. If new holes are needed, mark the spots to drill, set aside the steps, and drill the new holes.
5. Align the mounting holes with the holes on the outriggers (if needed), the holes left from the previous steps, or the newly drilled holes. Make sure the bracket is backed up fully against the I-beam on the chassis.
6. Use carriage bolts and flange lock nuts for each side. Tighten until snug, then check that the steps are sitting square and level before torqueing the hardware tight.
7. Connect the appropriate wiring to your vehicle's power source.

3722862 Lippert Components (LCI) Quickie 34 Series Motorized Motorhome Entry Steps - 2 Stairs - 7" Drop/Rise - 30" Wide - 300 lbs

Kwikee Part Number 903409025