bing tracking image
  1. RV Waste Valves
  2. Valterra
  3. Single Waste Valve - Manual
  4. 1-1/2 Inch Valve Body
  5. Straight Valve
  6. Stationary Valve
Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter

Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter

Item # T1001VP
Our Price: $13.53
You Save: 41%
RV Waste Valves
Shipping Weight: 0.53 lbs
Add to cart
In Stock
zoom in icon
slider vertical icon
zoom out icon
Comment field cannot be left empty.
Name field cannot be left empty.

Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.

Error submitting comment. Please try again momentarily.

Product Images

In Use/Installed

Customer Photos

Need help with installation?
Locate installers near me
Replaces the valve for your RV's gray-water tank. 1-1/2" Diameter passage allows wastewater to travel freely when valve is open. Valve body, seals, nuts, and bolts included. Great Prices for the best rv waste valves from Valterra. Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter part number T1001VP can be ordered online at or call 1-800-940-8924 for expert service.
  • All Info
  • Reviews (576)
  • Q & A (0)
  • Videos (2)
  • Photos

Valterra RV Waste Valves - T1001VP

  • Single Waste Valve - Manual
  • 1-1/2 Inch Valve Body
  • Straight Valve
  • Valterra
  • Stationary Valve

Replaces the valve for your RV's gray-water tank. 1-1/2" Diameter passage allows wastewater to travel freely when valve is open. Valve body, seals, nuts, and bolts included.


  • Replacement valve for your RV's gray-water tank
  • 1-1/2" Diameter passage allows wastewater to travel freely when valve is open
  • Plastic handle
  • Valve body, seals, nuts, and bolts included
  • Fits Bladex, Valterra, Bristol, and Anonda valves
  • 1-Year warranty

To install, remove the broken waste valve and seals from your gray-water tank. Then place the included seals on the flange fittings and position the new valve body. Tighten the provided hardware to complete installation.

T1001VP Valterra Bladex Motorhome Grey Water Holding Tank Waste Valve Body with Plastic Handle - 1-1/2"

Video of Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter

Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.

Video Transcript for Valterra Bladex RV Gray Water Tank Waste Valve Body Review

Adam : Hi, how are you everybody. Adam here with etrailer. Today, we're going to be taking a look at the Valterra gray water valve. So you could be replacing just your seals, maybe just the hardware, but today we're actually replacing the whole thing. So we're going to have new hardware because ours was rusting out. And also, new seals because we we're having a little bit of leaks.

So if that's something that you guys are having problems with, this is the video for you. We're going to go over the whole entire swap together.So this right here is going to be your replacement, gray water valve. It's going to have a diameter of an inch and a half, so make sure that it is the right size for your setup. We have other different sizes here at etrailer. So if it is a different size, we got you.

We got all the parts you need. And even if you don't need to replace the whole entire thing, we have replacement parts for everything you see here. And that's always a plus.We have a nice little handle, which is going to engage and disengage the valve to shut off or turn on that water flow to let it flow out. So if you get the whole entire replacement, it's all going to be made of plastic. We are going to get our nuts and bolts with it.

And of course, we're going to get the seals too. And that's always a plus. These are going to fit the Blatt X Valterra Bristol and Ananda valves. So don't really have to worry about cross-compating different brands. This works just as good as all the other ones.There's a couple of different reasons why I'm changing out this valve.

One, Jake told me that it was leaking and the seals weren't really holding up. So instead of just replacing just the seals and the screws, we did the whole entire thing. And we're going to go over that with you now.So first things first, we need to remove our valve. And to do that, we're just going to need a three eighths inch wrench and socket to loosen these up. So We had a little bit of an issue and another reason why we're kind of switching this out, all of our heads on our bolts snapped off. But what I'm going go ahead and do is just take a little punch. You can take anything that's going to fit in that hole and just give it a little good, a little tap, and it's going to break loose real easy ideally. Look at that. Look at that. Oh yeah. So I'm going to do that for all of them and then go ahead and take this valve out.So while we're going to be replacing our seals, the nice thing about it is, when we do get the seals, we don't have to drive these back in. Obviously, these are completely unusable because they're all seized up and stuff. So I'm going to get those out later. But now, the nice thing is our seals are bad, but we can replace them really easily and it does come with hardware. So we can replace both of them all in one go round, which is nice.So all you really need to do is take the new seals, and just put them in there. I mean, it's really, really that easy and it's going to be the same exact thing for the front and the back and check that out. Pretty much done deal. So everything's really working fine. I didn't have any leakage or anything like that. So I can just go ahead and use the new hardware to re-install this valve. So now with all of our new stuff, shouldn't have any leaks or anything like that, line it all up. Oh yeah. And put our hardware through just how it was before, just new stuff. And what I like to do is put them all in, get them all lined up and then I like to go through there and tighten them all down separately, but kind of going from one to the other.So meaning, I put this nut on here. I'll kind of tighten it down almost to the bracket there, and then I'll do like a star pattern. So I'll tighten this one down and this one down then this one and this one, that way, we're not going to be putting that seal under any weird angles. It's not going to get smushed. It'll just help everything go nice and smooth. So with the new hardware, we are going to have to have an eight mill and a 10 mill, whichever kind of tools you need to get it done. I'm just using a wrench and socket, but go ahead and tighten one up, not all the way. And then tighten the one back here up in that star pattern, kind of like the lug nuts on your truck, car, motor home. Now that everything is all secured down, the levers, moving there's a little bit more of a seal there and we don't have any drippage coming out from underneath.So everything's nice and sealed up and now we're good. Well, everyone, I hope this video kind of just helped you with the installation process, whether you just wanted to get a closer look at the valve itself, or if you wanted to stick around a little bit longer, I actually go and answer a couple of my coworkers questions about the valve. So definitely check that out. Did you know right away that this was where it was leaking I mean, I would assume that this is going to be the culprit of, the most common points of leakage or did you have to actually look around to figure it all out Adam : Oh no. You'll know. You'll know whether it's down here, where the two pipes smash that valve, that'll be one. Or if it starts coming out right here, and usually it doesn't, it's not that difficult. I mean, obviously do it on a dry day. You know what I mean You don't want to have to go over there, just sniff everything around to see if it's paint or not. You know what I mean So do it on a dry day or when everything's dry, but yeah, you'll be able to see obviously piping and stuff.There's a bunch of fittings all around here. There's one, two, three, and four different seal pieces together on the pipe. And then there's the seams for the valve. So you'll be able to see that. I didn't have to search around to answer your question. The handle on that valve, is it going to break off I know that's a dumb question because who knows And I guess it could. Adam : They will. I've seen it. I've seen it all the time. So that is why, if that happens to you, especially if you're in, let's say you don't have a cover and your valve's like this, so it's exposed and sees a lot of sun. And then it also sees a lot of cold. You know what I mean It's eventually going to crack and it will eventually break. I'm not saying, it might not. The one that comes with it, it will eventually break. Speaker 3: Yeah. The one we took off, it was looking pretty harsh. And I think that kind of lends to the whole thing of just replacing it all at one time, because yeah, your seals may be bad now, and it may be like half and half for the full thing. So why wouldn't you just do it all at one time and then have a fresh new setup for the valves Adam : I agree. But if you have a brand new valve, let's just say, Jake comes over here, just breaks it. Grab this. So this is a metal one. Can't really hear it, but it's metal. Trust me. This will solve that problem. And then the rod is metal too. But one thing I have seen, what you have to do is, it's kind of difficult. So on the ones that I took off, I couldn't even get the knob turn because it was just as old as the hardware, and the hardware was rusted away. So it was really, really seized up. If you're really dead set on keeping that valve and you don't want to spend the extra couple bucks to get the whole assembly, go for it. But this was a little bit easier, but you have to get a tool, I use vice channel locks to just hold it in place and then twist it off.So on all the replacement knobs, they're going to be threaded on the inside. And the nice thing about this is, these are all plastic, so all the threads are plastic. On the other one though, for some reason, it looked like it had a little metal insert in there, but that was, I'm not sure what brand that one was that we took off. It was pretty old, but they're all standard. You don't really have to worry about matching up the right pitch or whatever. They just thread right on and come right off. That's just an accessory part that we sell or replacement part, that handle Adam : Yeah. So if you do have the problem with this breaking, we have a solution. It's this, which won't break. I'm 100% positive I would break the plastic one. Adam : I'm with you. We almost broke it. Adam : And, the gray water valve has the gray handle and the black water has the black handle, right You can replace it with whatever you want. crosstalk 00:09:52. Functionally or anything. Adam : No, not really. I would suggest though, getting the metal one for the black water, because this seal is so much more intense than the other one, so much tighter, which is good. Speaker 4: It's holding back the flood gates. Adam : So we have a bunch of different, we have a bunch of different replacement knobs. So yeah, if you're knob breaks, we have replacements for exactly what it is. But then you have, also these kind, which is actually what was on the other ones where it has the little fitting on the inside. So this will rust out, and it did on the ones that are replaced. So that is, you just get the, spend the extra, a little bit of money to redo the whole entire valve. I mean, you're taking it off anyway, so just replace it. But we have all sorts of different little knobs. So some of them are plastic. The ones that come with them are plastic. These have the little inserts in them with threads. And then the metal ones, obviously just metal doesn't have an insert in it, just metal. So that's cool. When you get in there to replace the valve, is it typical that you're going to find other things that maybe mean maintenance as well, or is this just kind of a one and done thing Adam : It's one and done. It really is. So for instance, if you guys go over here, I mean, you got, you basically have this curved pipe, which goes outside, and then it has that plate. And that's one piece. So that's all sealed up, leading up to there and then it just is in, then there's the valve. And then on the other side we have the little plate converter piece and then the pipe. So basically, it's just two of the pipes just clamping down over this. So this is literally all that's in there. And then of course, within that, the valve there's just these two rubber seals. That's the only thing on the inside of there.So no, not really. I mean, unless you have a cracked tube or something like that, but then you've got a lot bigger problems. You know what I mean The valve's not going to do anything for you. So this is probably the easiest maintenance that you can do for this anyway. You don't have to cut any pipe and reseal or anything like that. It's just bolt in and you're good. Adam : That's why I'm just saying do all four. It's like if you're doing brakes on your truck, are you just going to do the back brakes or all you going to do all of them You know what I mean It's like, if you're in there do it. Speaker 5: You can tell and see whenever there's a problem. And you can tell and see whenever any of the bolts are corroded or it's starting to look grody. I think that's one of the good things about it is, you'll definitely be able to tell when you need to change it. Adam : Yeah. Stuff will be on your driveway. Speaker 6: I guess one, one thing that, it's kind of simple. It's a pretty, it's pretty smooth. It doesn't wiggle around. You don't have to give it a lot of force to push and pull it. Adam : Yeah. Here, let me grab something real quick. I mean, it's not, there's not a whole lot to it. I mean, this is the valve. I mean, you just have your seals that go in the ring here and there. I mean, it's just in and out. It's very, very simple, very simple gate. But yeah, it's easy. It's just like a little door, that's basically all it is. It just stands straight out, that's it So not a whole lot to it. It's not very, very mechanically advanced. It;s not difficult at all. It's just a valve. You have, there's the valves that are like a ball with holes and you have to twist it. Or then you got this kind of a valve, and that's what we're using. Speaker 7: Do you think there's any easier products to install or is this, there's not something that's easier than this Adam : If there's something that's easier than this, someone needs to bring it to me, because I don't really think it's possible. I mean, that's just me. I mean, if it is simpler and it works just as well then kudos. But I don't see that even being a possibility, just because it's four bolts, you know Okay. Well if you guys have any other questions, you guys can always email me. We're going to be doing this stuff all day. So I will talk to you guys later. Thanks for coming out. And that's going to do it for our look at the Valterra RV waste valve and I'm Adam with each trailer.

Customer Satisfaction Score:

Customer Reviews

Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter - T1001VP

Average Customer Rating:  4.8 out of 5 stars   (576 Customer Reviews)

Replaces the valve for your RV's gray-water tank. 1-1/2" Diameter passage allows wastewater to travel freely when valve is open. Valve body, seals, nuts, and bolts included.


Installation was slightly challenging as the gasket kept moving around taking several attempts to fasten it without losing the alignment of the gasket to the piping. These types of valves seem prone to allow slight leakage through the part whenever the smallest interference is met. I have to hose the inside of the tube and part every time in order to make certain that the raw sewage didn't cause a leak in the valve. But, once the seal's made with the piping, it worked better but still leaks a little at the valve due to the nature of these types of valves.


Another quality part from etrailer fast service And the part fit perfectly install it within minutes of receiving it



Love everything i have gotten from Etrailer. And everything is quality parts. Highly recommend them for all your camper parts.


Very quick turn around. Thank you


Very easy replacement, works like a cha rm


Replaced because handle was broken. Easy install. Sold trailer after installing


Great product -- it is what came with the unit when purchased and this is an exact replacement. Haven't install these last two waste valves, but did install the waste valve operated via cable system. It too was a Valterra; an exact replacement -- works perfectly. Very much appreciated the friendly and knowledgeable people at E Trailer for helping me with this project.


No more leaky valve. Arrived quick and just as described


Easy install. Works great.


just what I needed, when I needed it!


The Valterra waste water valves are well built and work effectively. The most important part of installation is to resist the temptation to over tighten them. Close the valve; place the rubber gasket in place and tighten the mounting hardware until just over hand tight. Test the valve for leaks. If there are any tighten each bolt/nut about 1/2 turn and try again. If still no joy, make sure the gasket is in place and try again. There is no need for excessive pressure on the valve structure to achieve a water tight seal.


Very good replacement valve comes with new gaskets and installation screws. Great value!

Phillip L.


Replacement valve installed easily and works great.


The products were super easy to order thanks to the videos and descriptions of what I was looking at. etrailer shipped the order the next day with lightening speed. I am looking forward to finishing my project and will gladly do business with etrailer again.


It is a pleasure ordering from Products are always in stock, no back orders, no excuses, no b.s..
Pleasant communication, products are shipped quickly and arrive on time. It is very refreshing to deal with
these professionals. I heartily recommend these folks for all your trailering needs.


Ordering from etrailer was extremely easy. Good friendly service with quality parts at a reasonable price. Along with fast delivery. I will definitely recommend them and order from them in the future! Now if the weather warms up we can go camping!!


The valve still works great. Makes me a happy camper!

James B.


Still works great. No leaks and smooth opening and closing. What more could I ask? The valve both still work great. No leaks and smooth opening and closing. Wha more could I ask?


Very fast service. Will use them again..


I haven't installed the valves yet, but the order was processed and arrived very promptly. The price was better than any other I could find, and the valves were complete with installation hardware and seemed to be the "real deal".


The product is great but the install has been very difficult. There just is no slack in the plumbing to slide the replacement back in. A problem with the RV, not the product.


I installed in in my shower gray tank drain to replace a broken unit, so far it has worked as advertised. I am very happy with it.


This unit fit perfectly. Very easy to remove old unit (cracked), new unit slid right in, the bolts and nuts included fit perfectly into existing plumbing. Have used several times to date: seals perfectly - no leaks!



The whole process was amazing!! Got exactly what I needed in excellent timing. Exceeded my expectations!! Thank you so much! I will definitely be using etrailer again!


Perfect fit for my 96 Roadtrek. Unscrew handle and screw original extension to it.


An exact replacement for my 33 year old valve. Great quality and price. Good for another 30 years.


Really happy with the ease of ordering, speed of delivery and information about the products ordered.


I still have install it but it is identical to the old one so I do not see any issues. As usual very satisfied with Etrailer!

Show More Reviews

See what our Experts say about this Valterra RV Waste Valves

  • Picking Out Replacement Seals for Valterra 1-1/2 inch Diameter Waste Valve
    The correct Valterra RV waste valve seals for 1-1/2 inch diameter valves is part # T1001-7VP for standard valve like part # T1001A or the part # T1001-9VP for if you have the Bladex style like # T1001VP.
    view full answer...
  • Recommended Replacement Waste Gate Valves For A 2015 Airstream Flying Cloud Travel Trailer
    If you're only trying to replace the gate valve and not wanting to cut any pipes then you can just unbolt the gate valves fro their mounting flanges by removing the four bolts holding them in place. You can then pull the pipes back slightly to pop the gate valve out and swap in the new one and bolt it back in place using the same bolts. You can use part # T1001VP for the gray tank and part # T1003VP for the black tank. I've attached a video below of a double waste valve I replaced where...
    view full answer...
  • Valterra Bladex Waste Valve Body for RV Gray Water Tank Thickness
    The Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter # T1001VP is 5/8" thick.
    view full answer...
  • Mounting Bolt Pattern for the Valterra Bladex Waste Valve Body
    Sounds like the part # T1001VP would fit as a replacement but you might want to remeasure. This valve has mounting holes that are 2-1/2 inches square.
    view full answer...
  • Mounting Bolt Pattern on the Valterra Waste Valve for RV Gray Water Tank w/ Cap part # T1001C
    The mounting hole on the Valterra Waste Valve for RV Gray Water Tank part # T1001C are 2.5" by 2.5". Should you just need the valve and not necessarily the adapters connected you can use Valterra Bladex Waste Valve Body for RV Gray Water Tank part # T1001VP which uses the same mounting pattern. This will also include new seals and harware. Check out the video on it I have attached.
    view full answer...
  • Replacement for Gray Water Waste
    What valve do you currently have on your RV? Most gray water tanks have a 1-1/2" valve. The Valterra Bladex Waste Valve Body for RV Gray Water Tank -with Aluminum Handle - 1-1/2" Diameter, # T1001VPM is a very cost effective replacement. This replaces the valve for your RV's gray-water tank, is 1-1/2" diameter passage. To install, remove the current waste valve and seals from your gray-water tank. Then place the included seals on the flange fittings and position the new valve body. Tighten...
    view full answer...
  • Determining The Correct Replacement Waste Valves For A 2004 Airstream Safari LS Travel Trailer
    If you're just looking to replace only the valves and nothing else then you'll just need the Valterra Bladex Waste Valve Body # T1003VP for your black tank and the Valterra Bladex Waste Valve Body # T1001VP for your gray tank. These valves just get bolted to a flange or double waste valve setup with four bolts. If you can send in a picture of what all you'd like replaced I can help you find the parts you need.
    view full answer...
    Image 1 for
  • What Size Gate Valve Is Needed To Replace The Gray Tank Waste Valve
    Yes, gray waste valves are 1-1/2". If you're replacing just the gate valves for your double waste valve then you can unbolt them and slip in the # T1003VP for the black and # T1001VP for the gray and then bolt them back in place. I've attached a video below where you can see how to do this. If you end up needing to replace the entire double waste valve then shoot me a few pictures from the other side so I can see the direction of the piping to find the correct replacement.
    view full answer...
    Image 1 for
  • Replacement Gray Water Tank Valve for 1999 Winnebago Minnie Winnie
    Since all gray water tank valves are pretty standard in size, you can use the Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter, part # T1001VP. To install, remove the broken waste valve and seals from your gray-water tank. Then place the included seals on the flange fittings and position the new valve body. Tighten the provided hardware to complete installation.
    view full answer...
  • Replacement Valves for the Double RV Waste Valves Part # T80
    You can replace just the valves on the Double RV Waste Valves part # T80. For the black water you can use the Valterra Bladex Waste Valve Body part # T1003VP and for the grey water tank you can use the Valterra Bladex Waste Valve Body part # T1001VP.
    view full answer...
  • 1-1/2 inch Valterra Bladex Waste Valve Recommendation for 1-1/2 inch Gray Water Tank Valve
    Since you have a 1-1/2 inch gray water tank valve what you'd want is the part # T1001VP for that size. We don't have an electric version of this though.
    view full answer...
  • Correct Spigot Flange for Valterra Bladex Waste Valve Body for RV Gray Water Tank
    The correct spigot flange for the Valterra Bladex Waste Valve Body for RV Gray Water Tank part # T1001VP is the Valterra RV Sewer Spigot with Flange part # T1006-1.
    view full answer...
  • Availability of 2 inch Diameter Valterra Bladex Waste Valve
    For the 2 inch diameter Valterra Bladex Waste Valve you'd want the part # T1002VPM. I attached a review video for more info on this as well.
    view full answer...
  • Valterra Replacement Waste Gate Valves, 3 & 1-1/2
    The Valterra Bladex Waste Valve Body for RV Black Water Tank w/ Drilled Stem - 3" Diameter, # T1003DSPB and the Valterra Waste Valve for RV Gray Water Tank - 1-1/2" Diameter, # T1001VP are per manufacturer designed to fit Bladex, Valterra, Bristol, and Anonda valves, they have an industry standard bolt hole pattern. The 1-1/2" Diameter, # T1001VP has a hole pattern of 2-7/16" x 2-7/16" center on center. The 3" Diameter, # T1003DSPB has a hole pattern of 3-11/16" x 3-3/4" center on center...
    view full answer...
  • T1001VP RV Waste Valve Handle Type
    The Valterra # T1001VP Waste Valve has a threaded on handle, but it will require a vise to hold the rod in place to get the handle to twist off. You may also be interested in the Valterra # TC172 Waste Valve, which is cable operated valve. The 72" cable will give you lots of mounting location options. I have included a link to the valve below.
    view full answer...
  • Replacement Grey Water Body/Seals for Bristol Double RV Waste Valves 34466ND13AAR
    The gray water tank valve on the Bristol Double RV Waste Valves part # 34466ND13AAR can be replaced using the Bristol Waste Valve Body for RV Gray Water part # 34439241 or the Valterra Bladex Waste Valve Body for RV Gray Water Tank part # T1001VP. If you just want the seals then that would be the Valterra Bladex RV Waste Valve Seals part # T1001-9VP.
    view full answer...
  • How Do I Replace A Handle On My Valterra Waste Valve
    I spoke to a Valterra representative and I was told that they do not offer a sleeve to slide over the two shafts to join them together. If the male thread has broken in the handle, and the coupler is still in working order, you may be able to use Extension Rod Kit for Valterra Waste Valve - Adjustable - 6" to 8" and 9" to 11", part # T1046-12VP. The extension rod and mounting bracket would attach to the coupler of the waste valve. If the coupler is not intact you will have to replace the...
    view full answer...
  • Replacement Waste Valves for a 2001 Winnebago Rialta
    If you can send me a photo of your waste valve setup then I may have an option for you but I don't know what you have now. If you cannot find an entire assembly then you might be interested in just replacing the valve as almost all assemblies use the same configuration, part # T1003VP for 3" or part # T1001VP for 1-1/2". If this will not work then again just send me a photo of your waste valve setup. Please note, we do not carry the piping that leads from the valve to the tank only the...
    view full answer...
  • Grey & Black Water Gate Valve Replacement
    The gate valves you are referring to usually come in 1-1/2" and 3" - most often 3". These gate valves are usually in your trailers "wet bay" and only need a short pull handle. But sometimes they are located nearer to the tank and require a long cable on the valve. For 3" valve with short handle use the Valterra # T1003VP valve For 3" valve with cable use the Valterra # T1003PBC valve For 1-1/2" with short handle use the Valterra # T1001VP valve For 1-1/2" with cable use the Bristol...
    view full answer...
  • Replacement Waste Valves for a 2014 Heartland Elkridge
    Yes, we have both economy and premium replacement valves for your 2014 Heartland Elkridge. However, in order to recommend options for you I would need to know what type of valves you have as well as their size. The most common is 3" for black water tanks and 1-1/2" for grey water tanks. In most cases there will be a wye in which the black and grey water outlet is combined but they can also be separate so I will need to know which you have. If you just need a replacement economy valve body...
    view full answer...
  • Replacement Tail Light Assembly For Obsolete Tail Lights On a 2012 Winnebago Access
    I have a recommendation for you as I cannot find any replacement lenses for your 2012 Winnebago Access. Even looking at Winnebago's parts catalog they do not show any options for your Winnebago. Instead you might consider installing the Dual LED Trailer Tail Light # CE86FR where your current lights sit. These lights are designed to surface mount to the rear wall and will function for the running lights, brake lights, turn signals and reverse lights like the factory lights. These are 9-5/8"...
    view full answer...
  • Availability of 1-1/2" Waste Valve with 24" Extension Rod
    The Valterra Bladex 1-1/2" Diameter Waste Valve # T1001VP and the 24" Extension Tube # TX24HPB would be all that you need for the setup you're looking for. The waste valve isn't available with this length extension tube already attached. On the Valterra Waste Valve the existing rod can simply be unscrewed from the main housing and the new threaded 24" extension would be screwed onto the unit in its place.
    view full answer...
  • Recommended Replacement Waste Valves For A 1998 Fleetwood Flair
    If you're wanting to only replace the valves then you just need the Valterra Bladex Waste Valve Body for RV Black Water Tank # T1003VP and Valterra Bladex Waste Valve Body for RV Gray Water Tank # T1001VP. You can just unbolt the old valves from your setup and swap in these new valves for an easy peasy installation.
    view full answer...
  • Mounting Hole Spacing of Valterra Bladex Waste Valve Body T1002VPM
    You can definitely use the Valterra Bladex Waste Valve Body for RV Holding Tank # T1002VPM. You're correct about the length not being a concern in regards to compatibility, what really matters is the 4-hole spacing, and for the Valterra # T1002VPM it is 2-7/8 inches, just like what you said you had. With your measurements in regards to the extension, it sounds like you are saying you have a slip hub such as the Valterra RV Sewer Slip Hub with Flange - 2" # T1005-2 which has a 2-3/4"...
    view full answer...

< Previous

Do you have a question about this RV Waste Valve?

Info for this part was:

Employee Jameson C
Expert Research:
Jameson C
Employee Jacob T
Video Edited:
Jacob T
Employee Cole B
Installed by:
Cole B
Employee Adam E
Installed by:
Adam E
Employee Amy B
Written by:
Amy B
Employee John S
Video by:
John S

At we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.