Valterra EZ Valve Double Electric Waste Valves - Rotating - (3) 3" Hubs

See what our Experts say about this Valterra RV Waste Valves

• Can a Second Switch be Wired in and Used with Valterra EZ Valve Electric Waste Valve # E1003VP
  Valterra EZ Valve Electric Waste Valve # E1003VP is operated with a switch and the valve would either open or close accordingly. If you are talking about just installing a second switch then it is possible though the switch is not available separately. You might be able to wire in two electric valves but both would either open or close together. But the switches may not be rated for the load of 2 electric valves. This one is fused at 5 amps so you would likely need a separate switch for...
  view full answer...
• Dimensions of Valterra EZ Valve Double Electric Waste Valves
  I went to take some measurements of the Valterra EZ Valve Double Electric Waste Valves # E85-8 and found it was about 12 inches wide as in the accompanying photo. The depth was more difficult because it is electric and there are wires on either side but you would need 8 inches at the least for it to fit, so a space that is about 12-1/2" by 8" minimum would be needed. Also keep in mind that you will need to use ABS Solvent Cement # A05-0303 for installation.
  view full answer...
  
• Does Valterra EZ Valve Double Electric Waste Valves Need to Install Near Both Pipes
  Thanks for the photos, and you will need to install the Valterra EZ Valve Double Electric Waste Valves - Rotating - (3) 3" Hubs # E85-8 further up. The valves need to connect to your gray and black water tank and then to the down pipe; to secure the EZ Valve to your pipes you will also need the Valterra ABS Solvent Cement # A05-0303. I have added a link below to the installation instructions for you to check out as well of the Valterra EZ Valve Double Electric Waste Valves # E85-8.
  view full answer...
  
• What is the Difference Between Valterra EZ Valve Electric Waste Valves # E85-8 and # E84-8
  The difference between the Valterra EZ Valve Electric Waste Valves # E85-8 and # E84-8 is the design of the center output tube. On # E85-8 it's a straight, regular hub. On # E84-8 the center tube has bayonet fittings. Based on your pictures you would need # E84-8. However, the input size of either hub is 3 inches so your smaller tubes would not fit without adapting to the tubing size you have up to a 3 inch mating tube to fit the E84-8. It looks like the smaller tubes are 1-1/2 inch (measure...
  view full answer...
  
• Can You Replace Just the Valve When Upgrading To Electric Sewer Waste Control
  In order to upgrade from manual to electric waste control valves you'll need to change out the entire housing/body as well. For this, we have quite a few options which will depend on if you have separate valve like part # E40B-8 or combined like part # E85-8. These options both have hub fittings which are the easiest to change out since all you need to do is cut the old ones off and slide the new ones on with some solvent part # A05-0303.
  view full answer...
• Orientation of Valterra EZ Valve Double Electric Waste Valves for Install
  The Valterra EZ Valve Double Electric Waste Valves # E85-8 is essentially a manual system with an electrical function that moves the manual waste valve handle. This means that you basically just have to install it so that the handles won't make contact with anything under your RV. If you check out the attached installation instructions you can see the section about the valve installation. To complete you're installation you'll also need the solvent # A05-0303.
  view full answer...
  
• Are Cable Actuated RV Waste Valves Prone to Being Troublesome
  Michael, I'd say what you're reading is a bit of both them being a bit troublesome but also the installer installing it incorrectly. The cables can be prone to bounding issues, but that does not necessarily mean that it will happen to you so I wouldn't really worry about it. As long as you keep on top of your sewage system, you shouldn't run into any issues.
  view full answer...
• Length of Wire Between Valves and Switch Panel Valterra EZ Valve Double Electric Waste Valves
  For the Valterra EZ Valve Double Electric Waste Valves, # E85-8, the length of wire that runs between valve and control panel is 76".
  view full answer...
• Repositioning RV Waste Drain Valves
  The Valterra EZ Valve Double Electric Waste Valve # E85-8 is designed to connect to two horizontal 3-inch waste pipes to combine them for dumping through the central tube. From your photo I cannot tell if that is your setup. On this part the two bolt-on valve bodies can be unbolted, rotated to another orientation and then bolted back together. For installations that require it this can give you the needed clearance for the electric motor/handle assemblies. You do need to use ABS solvent...
  view full answer...
  
• Recommended Electric Dump Valves for 2014 Sanibel 3600 5th Wheel Trailer
  For the electric valves, we only have the 3 inch options. We have the hub to hub # E40B-8, the hub to spigot # E40-8, or the spigot to spigot # E40A-8. If you were to convert your 1-1/2 inch to a 3 inch, we do have the double 3 inch electric valves with 3 inch hubs # E85-8 or 3 inch hubs to lug fitting # E84-8. For your slide-out seal, I assume you are referring to weather strip tape like # WS1412 which can be combined with silicone sealants like # 0160297 for extra water protection....
  view full answer...
• Is There a Valterra EZ Valve Double Electric Waste Valve for 3" and 1-1/2" Valves
  The Valterra EZ Valve Double Electric Waste Valves are only available in 3". If you have a 1/2" and 3" setup then you will need to upgrade to 3" in order to use one. I recommend part # E85-8 and then part # T1041-1. You'll also need part # A05-0303 to complete the swap along with some misc. pipe.
  view full answer...

Do you have a question about this RV Waste Valve?