Replacement Exterior Pop-Up Roof Vent - Aluminum - 13-1/2" x 8"
(101 reviews)
Price: $40.59
Replacement Exterior Pop-Up Roof Vent - Aluminum - 13-1/2" x 8"
Retail:$45.63
Our Price: $40.59
You Save: 11%
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (101)
- Q & A (0)
- Photos
Redline RV Vents and Fans
- Roof Vent
- Vent
- No Fan
- 8W x 13-1/2L Inch
- Silver
- Manual Lift
- Redline
- 2-1/2 Inch
Rust-proof aluminum pop-up vent opens in either of 2 directions so you can scoop in fresh air or keep out rain no matter which way the wind is blowing. Opens and closes with easy-to-use lever. Includes built-in screen. Silver color.
Features:
- Rust-proof aluminum vent is made to last
- Two-way pop-up lid gives you the choice of opening the vent toward either the front or the back
- Adjusts in steps from fully closed to fully open, giving you complete control over amount of airflow
- Convenient lever spans entire length of vent - easy to find and operate
- Built-in, heavy-duty screen keeps out bugs, leaves, and any other outdoor things that you don't want in your trailer
- Gasket included to prevent leaks
- Interior trim piece (2756; sold separately) adds a finishing touch to the inside of your trailer
Specs:
- Rough opening size: 11-1/8" long x 5-1/2" wide
- Overall dimensions: 13-3/8" long x 7-3/4" wide x 3-1/2" tall
- Rounded radius corner
- Vent extends above roof:
- 2-1/2" Closed
- 5" Open
- Inside bar (handle) dimensions:
- Length: 10-1/4"
- Distance past flange: 1"
- 12 Screws (sold separately) required for installation
- Hole diameter: 3/16" (fits #8 screw)
RV-626-062 Redline 2-Way Pop Up Ventilator - Aluminum - 13-1/2" x 8" x 3-1/2"
Item # RV-626-062
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- Did not fit
Customer Reviews
Replacement Exterior Pop-Up Roof Vent - Aluminum - 13-1/2" x 8" - RV-626-062
Average Customer Rating: 4.8 out of 5 stars (101 Customer Reviews)
Rust-proof aluminum pop-up vent opens in either of 2 directions so you can scoop in fresh air or keep out rain no matter which way the wind is blowing. Opens and closes with easy-to-use lever. Includes built-in screen. Silver color.by: Patrick F01/25/2019
This vent was bought to replace one of the roof vents on my recently purchased used horse trailer. The top section of the existing vent was completely missing so rain could come right on in. It was easy enough to remove the damaged vent. Took a bit of elbow grease to remove the old sealant off the roof. The new vent is EXACTLY the size needed and installing it took less than an hour. Now the vent is fully functional once again and no more rain coming straight into the trailer either!
by: Gregory06/28/2023
These vents have been holding up perfectly. Great for transporting the dog or goats when it's warm out. I mounted them to a fiberglass truck cap.
by: Jim H08/16/2016
I needed these vents to get more air into my older Kingston trailer that has a small tack room, although there is a window that opens on front it does not allow enough air into horses because of the petition, so I installed two of the vents from etrailor and now I have great air flow to my horses. I would recommend when a person orders the vents that they have nuts and bolts sent at the same time, I used stainless steel but that entailed a trip to the hardware store.
These vent came well packaged and in a timely manor, well made and should last a long time.
Thank you! Jim H
Jim H.
8/17/2017
I go back and forth to Florida so its a must to get air flow into my trailer and these work great!
by: great item..fair price 09/02/2016
this is a high quality item. I needed smaller size Vents to fit in between the ridges on the roof of a Ford van. I bought two of these and receive them in a timely fashion. I was pleasantly surprised at the level of quality. this company seem to be very dedicated to making sure I was satisfied via the numerous emails. Thank you
by: Beth 04/25/2023
Item was exact replacement I wanted. Came very quickly.
by: Peter07/07/2023
They look great
by: Steve S06/07/2017
Love this vent! It was fairly easy to install, and works great. It was installed in the tack room/dressing area of a 2 horse trailer. The tack room was like an oven with no fresh air and this vent has completely alleviated that problem.
The website was easy to use, the product was reasonably priced, and the product arrived timely.
We have no complaints, and recommend etrailer.com to everyone!
Steve S.
6/11/2018
We love it! Works great & has made a huge change in the inside temperature of the tack room. Much cooler now. Thank you
by: Mark 09/19/2022
The vent is well made and was easy to install. The folks at e trailer were more than helpful in this transaction. We highly recommend this company and make all of our trailer parts purchases with them.
by: Barry 02/16/2023
Perfect replacement part match,thanks.
by: James Mc07/11/2017
Not my first order from etrailer and definitely not my last. My only complaint would be in the packing of small or fragile items loosely in a box with heavier items. One of the trailer light mounts was broken when it got here. No other issues though.
Laura E.
7/15/2017
We do our best to package our orders so that they will arrive to you in good condition. I will send this to our shipping department manager for review.
by: John L12/22/2017
Haven't installed yet. Will be adding to my 5x8 RV trailer. I just spent 4 nights camping in rainy weather and found I need better ventilation than just side windows. This looks like a good add on for me when paired with a vent fan. Conveniently bought a Ventline Ventadome Trailer Roof Vent with 12v Fan at the same time as this pop-up vent. Will install the pop-up vent in the rear wall of the trailer and the Roof vent at the front. These two items together should keep the trailer ventilated for both Air Conditioning and Electric Heating without allowing excess moisture or rain through the windows. Only gave 4 stars because I haven't yet installed these items.
by: Beverly J.05/20/2013
I ordered this product to use as a vent in my horse trailer tack room to vent out a generator exhaust. This generator is plugged into my truck camper so I can have AC when not plugged in to electric. I have show dogs that travel with me. I have used this type of vent before, and they work well, but this is the first time I have ordered from etrailer. What a superb company to do business with. The order was instrumented immediately, and sent ahead of schedule and arrived before the delivery date!! I will order from etrailer again when needed. I will send a photo when the vents are mounted. Thank you.
by: Sam N06/27/2019
Awesome vent unit. Installation was straight forward, and a foam gasket is included. This is the same type of vent used on USPS, FedEx, and UPS delivery trucks.
I painted mine white to match the 99 E250 I put it in. I installed this to give my single rear seat some extra airflow.
For installation, I traced the inner diameter of the gasket, and marked each of the 12 mounting holes. I drilled a single 1/2" hole to insert a pneumatic body saw into and cut along the line I traced. Then I drilled the holes. I chose to use nut-serts as my fastener. I drilled the mounting holes on the vent bigger, and inserted the rivet-like 10-24 nutserts. Then I added some silicone to both sides of the gasket and bolted it in. I filled that up with a bead of elastomeric caulking on the outside.
I haven't felt the airflow yet, but it should be sufficient with the pop-out windows on the doors. Overall I'm very pleased with the purchase.
by: KEVIN K04/15/2013
Perfect match for my enclosed trailer. I Rubbed the side of my enclosed trailer against some trees. I thought I would have to go back to where I bought the trailer and get ripped off for the part I needed. Looked on the web and found your website. I found that you stock a large supply of parts for both my trailers, fast shipping and excellent customer service. Outstanding! Thank You.
by: BLS09/30/2019
Received trailer roof vent promptly from etrailer. Took to trailer service business for professional to do replacement of roof vent. Technician said the screw holes aligned perfectly making the job quick and easy. The aluminum roof vent looks like the original on my Featherlite horse trailer so I am very pleased.
by: Darwin05/23/2019
Well built , will work fine ...
... with gas and propane in pickup topper for generator , this will work great for ventilation . Positions are great and the weather stripping around lid ,will seal great when closed ....rain OR snow
... all around great and well put together ...
... as usual etrailer has 1st class items , great prices and fast shipping ...
by: Ed P08/23/2020
This vent has worked out very well as a replacement to the plastic manufacture orginal.
I have even been asked to retrofit some other friends trailers with it.
Edward P.
8/25/2021
Worked so well I have purchased another.
by: John10/04/2018
I bought these vents to put in the topper of my truck to get some airflow for our dogs. We travel with them from Iowa to southern Missouri and in the summer it gets far too hot in the bed of the truck to travel for long, making the 8 hour trip take much longer. I sat in the back with our dogs to test out the airflow while my wife drove us around... Wow is the airflow good! These vents look good, function well, are easy to install, and they do exactly what I wanted them to. Very satisfied with these vents.
by: Michael K.06/04/2016
I haven't installed this product yet. Quality of vent is excellent. Installation looks to be simple and easy. Aluminum makes this vent light weight and heat reflective. Good qualities for a roof mount.
by: dml03/24/2017
Worked great... smoother than the OEMs that were in the trailer, and the holes for mounting lined up perfectly
by: Eric L.10/24/2012
Vent is well constructed of aluminum throughout. The bezel is dead soft and forms easily to whatever contour is needed. Fastening is quick and simple with sheet metal screws. The gasket forms a good leak proof seal on a clean surface, even it the screws cannot be sealed from the back. A lot cheaper than A/C!
by: Bob F10/24/2013
As is always the case with Etrailer I received my vents in record time and as usual was very satisfied with the quality of the product that I received. My dealing with Etrailer have always been more that satisfactory.
Bob Fleury
by: Greg D.02/22/2021
My originals vents were rusted and became inoperable. I ordered 4 new ones. A perfect fit over the existing holes, had to purchase sealant from Lowes, installed in an hour. One year later, no leaks, open and close smoothly...and they are still shiny as the day I bought them.
by: kelly erfle03/28/2012
excellent product, fast shipping, excellent customer service.
25
101
Show More Reviews
See what our Experts say about this Redline RV Vents and Fans
- Aluminum Roof Vent with Interior Plastic Piece The closest vent assembly we have to what you described is the Redline 2-Way Pop-Up Roof Vent # RV-626-062-2756. This aluminum vent includes a black plastic inner garnish that's going to help hold the vent in place while also allowing for a nice clean look inside the trailer. The vent can open in 2 directions to help with air flow regardless of which direction the wind is blowing outside. This will fit a rough opening size of 11-1/8 inches long and 5-1/2 inches wide. Its overall dimensions...
view full answer... - Can the 2-Way Pop Up Ventilator be Installed on the Side of a Cargo TrailerI went to the warehouse and pulled the 2-Way Pop Up Ventilator, # RV-626-062, and checked to see if there is a gasket in the opening of the vent and there is. This should keep weather out of the vent when closed. I did a short video showing the gasket and how the ventilator works to open in either direction. Your main concern might be that the vent will stick out 2-1/2 inches when closed and 6-1/2 inches when fully open. As long as the fenders are out farther than this on the sides of...
view full answer... - Size of Hole and Rivet Size Recommendation for Replacement Exterior Pop-Up Roof Vent # RV-626-062 The screw holes of the Replacement Exterior Pop-Up Roof Vent # RV-626-062 that you referenced are 3/16 of an inch in diameter. Typically we recommend number 8 screws for the install of this. A number 11 size rivet is commonly associated with this hole diameter so that would most likely be the size used for installing this.
view full answer... - How Does the Top of the Exterior Pop-Up Roof Vent Stay OnThe top of the Exterior Pop-Up Roof Vent # RV-626-062 has 3 flanges that a metal bar runs through. This holds the top on because the metal bar does not fit through the top to come through. This metal bar is also what allows it to open on either side, the metal bar slides to one side or the other to pop the top open. The vent itself would be held on by 12 screws (not included). I have included a picture that shows the metal bar running through the flanges.
view full answer...
- Does Exterior Pop-Up Roof Vent Need to be Installed Horizontally to Avoid Rain Getting InIt would be possible for water to get in vent # RV-626-062 if the opening is facing the direction the water is coming from. To avoid that you can mount the vent in such as way so that the opening faces downward.
view full answer... - Lid Dimensions Of The Redline Exterior Pop Up Roof Vent I've attached pictures showing the pretty much every dimension of the Replacement Exterior Pop-Up Roof Vent # RV-626-062. If you need any other measurements please reply back and I'll get them for you.
view full answer...
- How Does the Replacement Exterior Pop Up Roof Vent OpenThe Replacement Exterior Pop-Up Roof Vent # RV-626-062 can only be opened from the outside. To open the vent you're going to need to rotate the handle down or up and push. These aren't terribly hard to open so if it's not still opening you probably have a defective unit.
view full answer... - Can The Lid Of The Replacement Exterior Pop-Up Roof Vent # RV-626-062 Be Removed The bracket that holds the lid of the Replacement Exterior Pop-Up Roof Vent # RV-626-062 is riveted to the vent so you'd likely have a hard time trying to remove it without damaging it. Removing the entire vent from the roof of your trailer would just require you drilling down into the rivet and clearing off any sealant so it would probably be about the same difficulty as removing the lid and then trying to reinstall it on the old vent and rivet it in place. Personally, I'd just replace...
view full answer... - How Would Rivets Remove on Trailer to Install the Redline Roof Vent # RV-626-062 In Place of itWhat you described are rivets. They have to be drilled out as they don't have a nut or screw that unthreads. You want to find a drill bit thats about half the diameter of the rivet and then drill it through the rivet to pop it off.
view full answer... - What Size Opening Is Needed To Install the Redline 2-Way Pop-Up Roof VentIn order to make sure you cut the right size opening to install the Redline 2-Way Pop-Up Roof Vent with Garnish for Enclosed Trailers part # RV-626-062-2756 I recommend using the gasket or the interior garnish as your template but the rough size opening needed is around 11-1/8" long x 5-1/2" wide. The vent has radius corners which is why it is best to use the gasket or garnish as a template.
view full answer... - Comparison Between the Aluminum 2-Way Roof Vent # RV-626-062 and the Black 2-Way Vent # 9106For all intents and purposes there really is no functional difference between the Replacement Exterior Pop-Up Roof Vent # 9106 and the Ventilator, Pop Up 2-Way Aluminum with Screen # RV-626-062. Either would work just as well as the other with the only real difference being that one is painted black and the other is aluminum. Both could be used as a top vent.
view full answer... - Does the Redline 2-Way Pop-Up Roof Vent Have Screen and How Tall is GarnishThe Redline 2-Way Pop-Up Roof Vent # RV-626-062-2756 has a screen on the top of it, but it wouldn't keep small bugs out as the holes aren't that small. The garnish is 2 inches thick, but that doesn't mea this can't be installed on a thicker wall if needed. The garnish just wouldn't cover up all of the hole cut out for the vent.
view full answer... - Dimensions of Opening to Install Replacement Exterior Pop-Up Roof VentYou will want to make an oblong opening in your van that is 11-1/8" long x 5-1/2 wide. If you have access to a hole saw this size for a drill the wold be the cleanest way to cut the hole. A smaller hole could be used though you will get less airflow. Using a silicone sealant like part # 0160297 is recommended to prevent water intrusion.
view full answer... - Will Ceiling Garnish # 2756 Work with Pop Up Roof Vent # RV-626-062Yes, the pop up roof vent garnish part # 2756 that you referenced does work with the pop up roof vent part # RV-626-062 that you referenced.
view full answer... - Can the Redline 2-Way Pop-Up Roof Vent with Garnish Be Placed Anywhere on a TrailerThere isn't a right or wrong way to place trailer vent # RV-626-062-2756. It can go on the roof, on the sides, front, or rear. Putting it on the sides, front, or rear and having it open at the bottom would help keep out rain. Ultimately it is up to you where to put it!
view full answer... - Is Redline 9106 Black Steel Pop-Up Roof Vent Available in White Color or in Plastic VersionThe Redline oval-shape Exterior Pop-Up Roof Vent # 9106 is not offered in white nor does it comes in a plastic version, but we do offer it in unpainted aluminum as part # RV-626-062. We also have this vent with a garnish (interior trim piece) included as part # 9106-2756 in black steel and as part # RV-626-062-2756 in aluminum. All include a gasket to prevent leaks.
view full answer... - Replacement Fresh Air Intake Vent For A 2006 Forest River Grey Wolf TT Toy HaulerThe only thing I consistently pulled up with part number PBD 877-646-9233 was plastic pop-up vents. Here are the available options for your for a 2006 Forest River grey Wolf TT Toy Hauler : Replacement Exterior Pop-Up Roof Vent-Black Steel Item # 9106 Replacement Exterior Pop-Up Roof Vent - Aluminum Item # RV-626-062 Redline 2-Way Pop-Up Roof Vent with Garnish Item # 9106-2756 Redline 2-Way Pop-Up Roof Vent with Garnish Item # RV-626-062-2756 Both are 13-1/2" x 8" and do not have to be...
view full answer... - Does the Enclosed Trailer Aluminum Roof Vent, # RV-626-062, Come with a GarnishThe Aluminum vent, # RV-626-062, comes with the vent itself, built-in screen, and a gasket, but not the garnish. The enclosed trailer vent, # 9106-2756, comes with the vent assembly itself, the black garnish that can be trimmed if you have a thin roof, a built-in screen, and a gasket. If you like the look of the first one, you could always paint this black vent to the color you wanted.
view full answer... - What is Trailer Roof Vent # 9106-2756 Made OfI went and pulled a trailer roof vent # 9106-2756 from the warehouse. I used a magnet to check to see if it was steel and the magnet immediately stuck. This is not a fool-proof way to determine material but given the other characteristics of the vent, the black powder coat, that is a strong indication that it is steel. We have a similar aluminum model, # RV-626-062.
view full answer... - Recommended Trailer Side Vents On Emergency Response Trailer For Increased VentilationYes. Installing the Redline 2-Way Pop-Up Roof Vent with Garnish for Enclosed Trailers - Aluminum # RV-626-062-2756 is a great option for a side mount or roof mount. It will allow air to move and will keep your equipment from issue as long as the gas cans and machinery are in working order and not leaking gas. If everything is functioning as intended, I recommend a vent on each side to have enough ventilation to keep this trailer from being hazardous or a couple of vents on the roof. .
view full answer... - Will Redline 2-Way Pop-Up Trailer Roof Vent with Garnish Fit the Curved Roof of a Teardrop TrailerThe gasket that comes with the 2-way vent # 9106-2756 is flexible enough that it should work well on a slightly curved surface. However, I would still use some silicone sealant like # 0160297 for additional protection. We also have this vent in an aluminum finish, # RV-626-062.
view full answer... - Recommended Vents For An Enclosed Box Truck hauling Horses The Vent for Enclosed Trailers - Aluminum - 12-1/4" Wide x 10-1/2" Tall # PLR20 is the largest wall vent we offer so it should offer your horses quite a bit more airflow. The sliding lever allows you to easily open and close the vent to adjust airflow. The aluminum construction is durable, lightweight, and corrosion resistant. Another option you might consider would be to install the Redline 2-Way Pop-Up Roof Vent with Garnish for Enclosed Trailers - Aluminum # RV-626-062-2756 on the...
view full answer...
- Availability of Redline Pop-Up Roof Vent # 9106-2756 in Sliver FinishThe roof vent you mentioned is available in an aluminum finish as part # RV-626-062. The vent includes the screen and the gasket. The garnish, which is not included is part # 2756.
view full answer... - Is Inside Trim Included With Redline 2-Way Pop-Up Roof VentThe interior trim garnish is indeed included with the Redline 2-Way Pop-Up Roof Vent, part # RV-626-062-2756. This vent also includes a gasket to help seal the vent and prevent leaks. For installing the vent we also offer either sheet metal screws, part # 31071, or wood screws, part # 30587. If you wish to use a silicone caulk to seal the vent and keep out moisture I recommend part # 0160297.
view full answer...
Do you have a question about this RV Vents and Fan?
Info for this part was:
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jameson C
Updated by:
Raymond P
Updated by:
Wilson B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Patrick F.
1/26/2020
One year later and the new vent is still working perfectly!