Westin Driving Lights - Stud Mount - 5-3/4" Diameter - Round - 1 Pair

Ask the Experts about this Westin Off Road Lights

• Will # 09-0205 Driving Lights Work with Westin # 30-0025 Safari Bar on a 2001 Mazda Tribute?
  The Westin # 09-0205 Driving Lights will work absolutely perfectly with your # 30-0025-1155 Safari Light Bar. They were unfortunately not able to provide me with any information about the amperage draw of the light kit. As far as the lamps causing an inadvertent draw on the battery goes, you won't need to worry about that happening as long as the lamps are installed according to the installation instructions.
  view full answer...
• Where Does the Yellow Wire of the Westin Driving Lights # 09-0205 Run To
  I attached a diagram for the install of the Westin Driving Lights # 09-0205 that you referenced. The yellow wire needs to run to a parking light circuit. You will want to use a quick splice like part # SWC501746-1 to tap into this circuit. You will need to use a circuit tester like part # PTW2993 to test the wires of the running lights on your vehicle till you find a circuit that comes on when the running lights are on and then connect to that wire.
  view full answer...
• Which Bulbs Do Westin Driving Lights # 09-0205 Use
  The Westin Driving Light, part # 09-0205 uses a 55W H3 bulb like part # P230003NW.
  view full answer...
• What is the Difference Between Driving Lights and Off-Road Lights
  Some of the exterior vehicle lights we carry are listed from the manufacturers as driving lights and others they list as off-road lights. The differences between them in most every case is the intended applications for the lights which is determined by the manufactures in the conception and design phases of development. Basically, the lights listed for off-road are best suited for off-road applications. They tend to be larger as well. The lights listed as driving lights are more suited...
  view full answer...
• Troubleshooting Westin Driving Lights Malfunction When Vehicle Parking Lights are On
  Since the lights function properly except when the harness is connected, something in the harness, or associated with it, is preventing the circuit from being completed. This sounds like a grounding issue. There are 3 wires that need to be properly grounded, the vehicle switch, the lights themselves, and the ground from the relay. Please check all of these grounds and make sure that they are attached to an appropriate metal surface and are properly grounded. Also check the connection...
  view full answer...
• Are the Westin Driving Lights # 09-0205 DOT and SAE Approved for On Road Use
  The Westin driving lights, # 09-0205, should be used as supplemental lights but are not designed to be primary vehicle lights. My contact at Westin confirmed that the 55 watt halogen bulbs produce a white light that is a DOT approved color and intensity. The SAE would factor in with the construction and function of the lights but not the legality of them. That rests with the DOT.
  view full answer...
• Do the Westin Driving Lights Install to the Parking Lights or Headlights
  To install the Westin Driving Lights # 09-0205 you would not necessarily have to run them to the running lights of your truck. I spoke with one of our installers and they told me that technically you will want to wire this to the low side of the headlight wiring on your 2005 Ford F-150. You need to run the wiring to a switched circuit so that there is not power running to the relay all of the time. All of the wiring would be completed in the same manner as explained in the video but...
  view full answer...
• Replacing Bumper Mounted Off-Road Lights on 1999 Jeep Wrangler Sport
  Since the factory circuit was rated for a maximum of 20 amps, and the Westin # 09-0205 Driving Lamps draw up to 9 amps per light, you could certainly install them using the existing factory circuit and wiring. Keep in mind that the original lights might have been removed due to a wiring problem, so you should not assume that the existing wiring is in good condition. I would recommend examining the circuit, if possible. I've linked you to an install video that I hope you'll find helpful.
  view full answer...
• Can I Install a Second Set of Driving Lights on the Same Relay and Switch as the Current Lights
  I spoke with my contact at Westin and he said you can install a second set of driving lights on the same relay and switch as your current lights as long as they are the same lights. If they are different lights, then it is not guaranteed that the lights will work on the same relay and will need to be wired separately.
  view full answer...
• Wiring Installation For Westin Driving Lights On 2005 Ford F-150
  I spoke with one of our installers and they told me that technically you will want to wire this to the low side of the headlight wiring on your 2005 Ford F-150. You need to run the wiring to a switched circuit so that there is not power running to the relay all of the time. All of the wiring would be completed in the same manner as explained in the video but to the low side of the headlight wiring. It is not necessary to install it to the parking light wiring.
  view full answer...
• Can Light Bar Be Mounted On Westin MAX Bull Bar with Winch Mounting Tray for a 2012 Ram 3500
  The correct Westin MAX Bull Bar with Winch Mounting Tray for a 2012 Ram 3500 is part # 46-43555-23555. The top tube of this bull bar has pre-drilled holes which will accept stud mounted lights like the Westin Driving Lights part # 09-0205. If you wanted to use the MaxxTow Off-Road Light Bar part # MT80633 you'd need to drill new mounted holes.
  view full answer...
• Availability of Grille Guard with Winch Mount and Lights for 2005 Ford F-250/F-350
  There are several options to add lights to the Westin Sportsman Grille Guard # 40-1645, which I'll list below: Westin Off-Road Driving Lights - 6" Diameter - Black Powder Coat - Item # 09-0505 Westin Off-Road Driving Lights - 6" Diameter - Chrome Plated - Item # 09-0500 Westin Driving Lights - Bracket Mount - 5-1/4" x 2-1/2" - Rectangular - Item # 09-0305 Westin Driving Lights - Stud Mount - 6" x 4" - Rectangular - Item # 09-0405 Westin Driving Lights - Bracket Mount - 4" Diameter...
  view full answer...
• Grille Guard to Fit 2007 Chevrolet Silverado Classic 1500
  The Westin Sportsman # 40-1175 is a full coverage grille guard that will fit your 2007 Chevrolet Silverado Classic 1500. This guard will protect the front of your truck and has a nice rugged look to it. The uprights are coated with rubber, so you can use your truck to push heavy object without damaging them. The installation doesn't require any drilling but may require some modification of the lower bumper fascia if your truck has tow hooks. If you prefer a bull bar style the Westin...
  view full answer...
• Headache Rack for use with a Tonneau Cover on a 2017 Toyota Tundra
  As long as the tonneau cover you have on your 2017 Toyota Tundra installs inside of the bed rails then you should have no problem using a heachache rack such as the Westin HDX Headache Rack part # 57-8025 for black or part # 57-8023 for white. The lower crossbar on the headache rack sits about 2-3" above the bed rails therefore you should not need any additional parts when mating the two together. You can add a set of lights to the rack using the Westin Driving Lights part # 09-0205...
  view full answer...
• Does Aries Grille Guard for 1998 Dodge Dakota have Holes to Attach Lights
  The Aries grille guard # AA5041 for your 1998 Dodge Dakota does indeed have pre-drilled holes in the center crossbar for auxiliary lights. There are several light kits that you could use including # 09-0205 or for that rugged look use # 09-0505. Six inch diameter lights are probably about the biggest you would want to go.
  view full answer...
• Lights for Westin Sportsman Grille Guard 40-1605 for a Toyota Tacoma
  Westin Grille Guard # 40-1605 is set up to accept certain lights but not any specific light bars. The following lights could be used: # 09-0105 # 09-0205 # 09-0305 # 09-0405 That isn't to say that a light bar wouldn't fit. The space between the main uprights on the grille guard are nearly the same as the width from the inside of one frame rail on the truck to the inside of the other frame rail. Measure that width to determine the length of a light bar that will fit.
  view full answer...
• Recommendation on Lights For Westin Ultimate Bull Bar
  The off-road lights that I have available for the Westin Ultimate Bull Bar are as follows: Westin 6 Inch Off-Road Driving Lights, Black, part # 09-0505 Westin 6 Inch Off-Road Driving Lights, Chrome, part # 09-0500 For standard driving lights I have the following: Westin 4-Inch Round Driving Lights, part # 09-0105 Westin 5-3/4 Inch Round Driving Lights, part # 09-0205 Westin 5-1/4 Inch x 2-1/2 Inch Rectangular Driving Lights, part # 09-0305 Westin 6 Inch x 4 Inch Rectangular...
  view full answer...
• Will Westin Safari Light Bar # 30-0005-1435 Fit 2012 Honda CR-V
  The Westin Safari Light Bar with Installation Kit # 30-0005-1435 is a compatible fit for your 2012 Honda CR-V. I have included a photo link to the instructions for proper installation of the product to your vehicle. While the instructions say 2007-2009, I have confirmed with Westin the same instructions apply through the 2012 models of the Honda CR-V. If you are looking for lights for this light bar, I recommend the Westin Driving Lights 5-3/4 inch Round Halogen with Installation Kit...
  view full answer...
• Will Westin Contour 3.5 Bull Bar Fit 2018 Ford F-150
  I was able to get ahold of my contact at Westin who said that they actually don't offer the Contour bull bar for a 2018-2019 Ford F-150 so unfortunately is doesn't look like there is a way to get your current bar to fit but we do have some alternative solutions for you. The 2 closest Westin bull bar options that we have which are somewhat similar to the Contour 3.5 are the Westin MAX # 46-43745-23835 and the Westin Ultimate # 32-2455. The MAX comes with a winch mounting plate and allows...
  view full answer...
• Dimensions of Westin HDX Headache Rack # 57-8025 for 2011 Chevrolet Silverado 2500HD
  According to my contact at Westin their HDX Headache Rack # 57-8025 for 2011 Chevrolet Silverado 2500HD will sit once installed such that the top of its round horizontal top tube is approximately 23-inches above the bed rail surface. We also offer accessory lighting kits for use with this rack, such as the Westin Stud-Mount Driving Lights # 09-0205.
  view full answer...
• What is a Westin Ultimate Bull Bar Used For
  The Westin Ultimate bull Bar # 32-0245 is designed primarily to mount lights such as # 09-0205, act as a low coverage brush guard, and alter the appearance of the vehicle. It is not designed for any other more strenuous activities.
  view full answer...
• Light Bar Recommendation for 2006 Dodge Durango
  If you are looking for a roof top light bar, similar to those seen on Jeeps, I recommend taking a look at Carr Deluxe Light Bar, # CARR210341, and Gutterless Mount Kit, # CARR220542. I have included a link to all of the light bars that are available for your 2006 Dodge Durango. In order to complete the set-up you will also need lights like the Westin Driving Lights, # 09-0205. I have included a link to our driving lights for you.
  view full answer...
• Will the Westin Sportsman Grille Guard Fit a 2008 Dodge Ram Big Horn
  Yes, the Westin Sportsman Grille Guard, # 45-1950, will fit your 2008 Dodge Ram Big Horn. I have attached a link to the installation instructions. According to Westin, the installation for the Big Horn model will be the same procedure as the base model Dodge Ram. If you want to add driving or off-road lights, I recommend looking at the Westin Round Driving Lights, # 09-0205, or the Westin Rectangular Driving Lights, # 09-0405.
  view full answer...
• Can the Westin Light Mounting Bar be used with a Front Mount Trailer Hitch on a 2017 Ram 2500
  The Draw-Tite Front Mount Trailer Hitch Receiver part # 65063 and the Westin Off-Road Light Mounting Bar part 37-02595 both use the same mounting location on your 2017 Ram 2500. It does appear as if you could install the light mounting bar over the trailer hitch but as this would likely void the warranty offered with the trailer hitch, I cannot recommend you do this. If you choose to use the light mounting bar then the Westin Driving Lights part # 09-0205 would be a direct fit. I have...
  view full answer...
• Item # 40-0905
  For the Westin Sportsman Grille Guard part # 40-0905 I really like the Westin Driving Lights part # 09-0205 or the Westin Off-Road Driving Lights - 6" Diameter part # 09-0505. The 6" variety are a little more heavy duty and offers a grated cover to protect them. The 5 3/4" have covers as well but need to be removed before use.
  view full answer...
• Are there Mounting Tabs to Add Fog Lights on Westin HDX Grille Guard for 2008 Ford F-250
  The Westin grille guard # 57-2365 does not having mounting tabs for additional lights. The holes that would normally be there to add additional lights are being used to hold the mesh part of the HDX. To add additional lights such as # 09-0105, # 09-0205, or # 09-0405, you can use the universal light clamps, # 57-0005.
  view full answer...
• Does Install of Westin # 40-2375 Grill Guard Require Removal of Front Tow Hooks on 2013 Ford F350
  Installation of the Westin # 40-2375 Sportsman Grille Guard will not require removal of the tow loops. The installation brackets attach to the vehicle using the bumper bolts, as you can see in the photo I've edited for you. This grille guard would be a great fit for your 2013 Ford F350. The grille guard provides mounts for driving lights like part # 09-0205.
  view full answer...
• Recommended Bull Bar for 2007 Chevrolet Avalanche
  One of our most popular bull bars for your 2007 Chevrolet Avalanche is the Westin Ultimate # 32-2115. The Ultimate features a stainless steel skid plate and large tubing to protect your truck. Add Westin Driving Lights, like # 09-0205, for more a more off-road style. It includes all of the mounting hardware and doesn't require any drilling.
  view full answer...
• Is there a Bull Bar that Fits a 2000 Chevy S-10
  For your 2000 Chevy S-10 we have a couple of light bars that look similar to Bull Bars but their primary function is to hold additional lights. For black we have # 30-0005-1065. And for polished stainless steel we have # 30-0000-1065. If you wanted to add lights you can use # 09-0205.
  view full answer...
• Recommended Items Needed To Flat-Tow 2000 Honda CR-V
  The Roadmaster XL Base Plate Kit, part # 1528-3 is a great fit for your 2000 CR-V. This kit has removable arms when you are not towing. For a tow bar I recommend the Falcon 2 Tow Bar, part # RM-520. This tow bar folds up against the back of your truck when you are not towing. For lighting I recommend the Roadmaster Tail Light Wiring Kit with Bulbs, part # RM-155. This kit includes the bulbs and does not require tapping into the vehicle wiring. The # 118336 harness is not designed...
  view full answer...