/
Ford/
F-150/
2016/
AccessItem # A1010061
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
This item qualifies for Free Shipping
Extra-long, trim-to-fit mud flaps for Ford F-150s with modified suspensions protect your towed boat or trailer from rocks or road debris. Custom-fit frame provides a factory look and allows access to hitch pin and wiring. Clamps onto 2" ball mount.
Features:
Specs:
Note: A minimum of 3" of clearance is needed from the edge of the bumper step to the end of the ball mount shank to ensure a proper fit. If the ball mount shank does not align with the hitch receiver so that the hitch pin can be inserted - or if the Rockstar's frame cannot be positioned to hang straight and plumb - a longer ball mount will be needed to install the mud flaps.
Without mud flaps, traveling the rocky road to your favorite campsite or boat launch may lead to costly fiberglass repairs or a scratched up paint job on your towed boat, trailer, car, ATV, or snowmobile. Protect your investment with this stylish Access Rockstar mud flap system. These mud flaps shield what you tow and look great while doing it. Rockstar's hitch-mount design clamps onto your ball mount and the whole assembly simply slides into your hitch receiver. Openings in the frame allow you easy access to your hitch pin and trailer connector, and you can easily remove the flaps when you aren't towing.
The Rockstar hitch-mounted mud flaps come in 4 different sizes. These standard size mud flaps (highlighted in the image above) extend 1" beyond the frame to offer great protection for your load against road debris. These mud flaps are extra-long so that you can trim them if necessary to achieve the right clearance for your lifted or lowered Ford F-150.
Rockstar mud flaps just look cool on your truck. The smooth, shiny finish gives your Ford F-150 a stylish look, and the frame hugs your bumper tightly for a from-the-factory fit. And rounded top corners on both mud flaps offer a sleek appearance.
The support flange on the frame is designed to fit your bumper step. These custom details make the Rockstar kit one of the best-looking mud flap setups on the road.
The beefy mud flaps are made of a 1/2" thick rubber for superior protection. These mud flaps stay in place better than thinner mud flaps because the heavy-duty rubber construction helps to prevent flapping in windy conditions. They stay down where you need them - protecting your valuable equipment from mud and flying rocks. The smooth rubber surface also reduces ice and snow buildup for a cleaner look.
Rockstar mud flaps can withstand temperatures of up to 250 F, so they won't be damaged by the heat from your exhaust. If you have a modified exhaust system that brings your exhaust outlet closer to the mud flaps, a heat shield (A80807 - sold separately) is available for added protection.
The frame is constructed of sturdy, lightweight, rustproof aluminum.
You can install the mud flaps in a few simple steps. First, attach the included 2" x 2" ball mount clamp to the back of the custom frame using the included hardware. Slide your ball mount into the frame, and tighten the frame clamp loosely around the ball mount shank. Next, insert the ball mount into your hitch and secure it with a pin and clip. Adjust the frame until it sits level and plumb on your bumper. Adhesive discs (included) protect your Ford F-150 from scratches where the frame comes in contact with the bumper. Finally, secure the frame to your ball mount by tighening the clamp with a torque wrench.
Once the frame is properly installed, attach the mud flaps to the frame using the included stainless steel screws. Next, check the length of the flaps to determine if trimming is needed. It is recommended that the bottoms of the mud flaps sit 5" to 7" off the ground with your truck unloaded and at least 3" off the ground with your truck under load. Use a utility knife and a straight edge to trim the excess length off of the bottom of each flap.
To take off the mud flaps, simply remove your ball mount from your hitch receiver with the Rockstar frame still attached. You do not need to remove the flaps from the frame before removing your ball mount. The Rockstar mud flap assembly stays clamped to your ball mount for a quick installation the next time you need it.
Average Customer Rating: 4.0 out of 5 stars (1 Customer Reviews)
Extra-long, trim-to-fit mud flaps for vehicles with modified suspensions protect your towed boat or trailer from rocks or road debris. Custom-fit frame provides a factory look and allows access to hitch pin and wiring. Clamps onto 2" ball mount.by: 2fingers01/30/2017
Review from a similar Access Rockstar in Mud Flaps
Looks nice on truck, haven't backed it out of shop since I just installed over the weekend. Bolted up fairly easy to bolt up with the little women holding it plumb and level while I tighten nuts up. Will update after getting it out where I can get a look in the sunshine. 336737
Ask the Experts about this Access Mud Flaps
Do you have a question about this Mud Flap?
At etrailer.com we guarantee:
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.