TremPro 645 Silicone All Purpose Sealant for RVs and Trailers - Clear - 10.1 oz Cartridge - Qty 1

See what our Experts say about this Flint Hill Goods Lubricants Sealants Adhesives

• Basic Instructions for Making Holes for Fridge Vents in Trailer
  Hey Henry, thanks for reaching out! We don't have any videos or instructions on it currently, but basically you'll need to line up your fridge vents with the wall on your trailer and see where the cutouts will need to be. Then you'll need to make sure there isn't anything in that wall location that will be damaged when you make your cuts. From here you can install your vents like the Ventline Exterior Wall Vent # V2111-13 with the appropriate cutout size (10-1/2" wide x 3-3/4" tall) and...
  view full answer...
• How To Remove The Lens On LED Clearance or Side Marker Light # MCL40RB For Installation
  I have included a link to our product video of the similar Amber Clearance Light # MCL40APB below. This has the same design with an amber lens and in the video she demonstrates removing the lens. You can also slide a flat head screw driver between the lens and back of the Light # MCL40RB. Then you will be able to twist the screwdriver to separate the 2 parts. Be sure during installation no Silicone # FAS59FR gets on this part of the backing and it would make it very difficult to remove...
  view full answer...
• TremPro Silicone Sealant Available in Clear
  We have the TremPro 645 Silicone All Purpose Sealant # FAS59FR in clear. We currently do not carry the 644 formula in clear. The main difference is the 645 is paintable if needed. We currently only carry the 644 in White # 0160297 and Black # 0160299
  view full answer...
• What Is Needed To Seal Behind The Trailer Side Marker Light 328-K-51 During Installation?
  I recommend using Clear Silicone # FAS59FR when installing the LED Trailer Clearance or Side Marker Light # 328-K-51. This will allow you to seal the hole for the wiring as well as the holes for the screws. A Caulk Gun # PTW54295 is needed for the tube of silicone.
  view full answer...
• Will TremPro 645 Silicone All Purpose Sealant for RVs and Trailers Work with Plastic
  The TremPro 645 Silicone All Purpose Sealant for RVs and Trailers # FAS59FR would work great for you as it is a multi-purpose sealant that would work great with plastic.
  view full answer...
• Can The Wheel Masters Trailer Bubble Level Be Mounted On The Front of a Travel Trailer?
  The Wheel Masters Level Master 2 Trailer Bubble Level # WM67200 will not have an issue being mounted on the front of your travel trailer. The front of the travel trailer will either have a molded fiberglass cap that is ridged or have a similar construction to the side walls. The walls will use a 2"x2" wood or metal studs in the construction. I measured the screws in our warehouse and they are 1-3/16" long that come with the level. Be sure to use some TremPro 645 Silicone All Purpose Sealant...
  view full answer...
• Rear Ladder For 2020 Allegro Red 33AA
  Hello Charles. The best ladder we have for your Allegro Red 33AA is the Stromberg Carlson Exterior RV Ladder - Aluminum - 99-1/2" Tall - 250 lbs - Black # LA-401BA. You should also grab some butyl tape # AL68FJ and some silicone # FAS59FR to seal up where the screws go in. I have also attached an install video.
  view full answer...
• Is There a Spacer For the Furrion Vision S Side Cameras To Work On a Recessed Application?
  While we do not have a specific spacer for the Furrion Vision Side Cameras # FCE48TASL the 1/2" Spacer # TA25722-90F00 would be a good starting point. We also have it in a 1" Thickness # TA25723-90AD00 depending on how deep your recess is. These spacers already has a 1/2" hole through the center of it for running the wiring, and its polyethylene construction is not going to rust out over time. These will most likely need to be trimmed down to fit your opening. I find it best to use a fine...
  view full answer...
• Replacement Tail Lights For a 2021 Lance 2185 Travel Trailer
  The Optronics Streamline LED Trailer Tail Light # STL79RB is going to be the closest light we have to what was put on by Lance for your 2185 travel trailer. This light is 17" long, 1-3/8" wide and 1" tall. The mounting holes are spread 16-1/8" on center and like yours the wiring is offset. It is 8" from the top and 9" from the bottom to the wiring center. As the lights are going to be different heights I recommend replacing both of them so they match and use Clear Silicone # FAS59FR to...
  view full answer...
• Trempro 645 Sealant Availability
  Yes, I had the TremPro 645 Silicone All Purpose Sealant for RVs and Trailers - Clear - 10.1oz Cartridge - Qty 1 # FAS59FR added to the site for you.
  view full answer...
• Recommended Vent Sealant for a 2010 Forest River R-Pod Travel Trailer
  Hey Ruth, you're correct you are going to need to rip up that old stuff before you put some new sealant down. So since you live in Texas, I'd recommend going with the TremPro 645 Silicone All Purpose Sealant for RVs and Trailers # FAS59FR. This stuff works best in temps above 40 degrees, is clear in color so it'll match whatever painted surface you apply it to, and can easily be installed using a caulking gun # PTW54295. Keep in mind as well that this is only a 10 oz bottle considering...
  view full answer...
• What Sealant Can Be Used To Seal The Gaps On An Extrusion Trim Cover On A 2010 Carriage Cameo RL3?
  To seal any gaps you may have on your 2010 Carriage Cameo RL3 5th wheel, you can use the TremPro 645 Silicone All Purpose Sealant for RVs and Trailers # FAS59FR with the Performance Tool Heavy-Duty Caulk Gun # PTW54295. This sealant is multi-purpose, can adhere to most non-porous materials such as glass, aluminum, metal, and metal alloys, and because of its clear color it can be used with all paint and trim colors. We also have this sealant available in white # 0160297, as well as black...
  view full answer...
• How To Remove Optronics LED Clearance or Side Marker Light # MCL40RB For Replacment
  To remove the Lens # A44RB from the LED Clearance or Side Marker Light # MCL40RB you will need to place the tip of a flat head screwdriver between the lens and light assembly(see image). I recommend starting near the corners to reduce the risk of damaging the lens. Once you have the lens removed you will see the screws used to mount the lights. As this hardware is provided by the trailer manufacturer I cannot tell you exactly what it will have but a Philips head button screw is most commonly...
  view full answer...
• Replacement Entry Door Grab Handle For 2007 Logan Coach Aluminum 2GN XT Horse Trailer
  Based on images I found for your 2007 Logan Coach Aluminum 2GN XT horse trailer it looks like you will need the Optronics Tan RV Door Grab Handle # 01180089B. This handle is 11" long overall and we do not carry it in black like it looks like your trailer would have come with. I see most people replace these small handles for a larger handle like the # AH-150. This handle is 18-1/2" long and has a softer black rubber grip that will help prevent slipping when it is wet out. Having the extra...
  view full answer...

Do you have a question about this Lubricants Sealants Adhesive?