HitchMate Threaded Trailer Hitch Receiver Lock for 2" Hitches

Ask the Experts about this Heininger Holdings Hitch Locks

Do you have a question about this Hitch Lock?

• Locking Hitch Pin for Kuat Transfer 2 Bike Rack
  
• There is a solution for you, but the HitchMate Threaded Lock # HE6001 will not work with your Kuat Transfer 2 # TS02G. You'd want the Cable Locks and Hitch Lock for Kuat Transfer 2 Bike Rack # PTSCLK12, which includes a hitch lock that attaches to your existing threaded hitch pin. The kit also includes a pair of cable locks to secure your bikes. I've added a link to a video review of this lock set for you to check out as well.
  view full answer...


• Hitch Pin Recommendation for Older Thule Swing Away Bike Rack
  
• For a locking hitch pin to fit the Thule Swingaway bike rack you sent in a picture of the part # THSTL2 would the pin to use. For just the pin portion you'd want the part # 853-5917. Looks like that rack is installed in a RV hitch. You should note that Thule does not rate their bike racks for use at the rear of an RV due to the much rougher ride quality. I know that's not what you asked about but it's important that you know that.
  view full answer...


• Trailer Hitch and Bike Rack for 2017 Subaru Forester
  
• Yes, trailer hitch # E98839 fits your 2017 Subaru Forester and Reese Eclipse 4 Bike Rack # 63124 is compatible. This is a very good economical option for your Forester and the Eclipse will allow you to carry 4 bikes so long as they do not exceed the 30 lb per bike weight limit. If you are looking for locks to protect your investments you can use Cable Lock # e98891 to secure your bikes to the rack and Anti-Rattle Hitch Lock # HE6001 to secure the Eclipse to your hitch. Additionally,...
  view full answer...


• Lock Recommendation for Additional Security with the RockyMounts MonoRail Bike Rack
  
• The best lock recommendation we'll be able to make for your RockyMounts MonoRail 2 Bike Platform Rack # RKY10004 is going to be using the lock that comes with the rack plus a cable lock like the # e98891 which you can route through the safety chain loops of the hitch and through the wheels of the bike. This will give you an added layer of theft protection for the rack plus your bikes. The hitch pin lock you mentioned would not work with the hitch pin of the RockyMounts bike rack.
  view full answer...


• Hitch Pin Lock for an XPort 2 Bike Rack
  
• I have a solution for you, however part # SR0901 is designed to fit the threading of a SportRack bike rack, and likely won't work with your XPort 2. We've found in the past that later versions of the XPort, the Q-Slot, work well with Saris' hitch pin locking set, part # SA3022. You can get a cable lock add on for this set as part # SA984 if you'd like to fully upgrade your rack's security. This isn't a guaranteed fit, however we've had reports that it may work.
  view full answer...


• How to Lock a Rola Cargo Carrier or Bike Rack to a Trailer Hitch
  
• The best option to add a locking hitch pin to your Rola cargo carrier or bike rack would be to try either the Threaded Hitch Pin for Swagman 2" Hitch Racks part # S64027 or the HitchMate Threaded Trailer Hitch Receiver Lock for 2" Hitches part # HE6001. As you mentioned, they do not make a locking hitch pin specifically for their carriers but they have had success with other manufacturers. However, we have not tested any of the other manufacturer's hitch pins yet so I cannot guarantee either...
  view full answer...


• Can Reese Eclipse 4 Bike Rack # 63124 be Used with Front Mount Hitch on 2018 Ram 2500
  
• Yes, the Reese Eclipse 4 Bike Rack # 63124 referenced in your question can absolutely be used at the front of your 2018 Ram 2500 via a front mount hitch receiver. I do just recommend adding a cable lock like # e98891 and the HitchMate Threaded Hitch Lock # HE6001 to secure everything into place and help deter theft of your investments. As with any hitch-mounted rack used in this application you will just need to make sure that the rack doesn't obstruct your view too much. While it may...
  view full answer...


• Locks for Kuat Transfer 3 Hitch Bike Rack
  
• The Kuat Transfer 3 hitch-mount platform bike racks # TS03G, # TS03G-FB and # TS03B-FB all use the same Kuat hitch and 3 cable lock kit # PTSCLK13. We do have the lock kit for the Transfer 2 racks, part # PTSCLK12, to which you could add another cable lock such as # e98891. The Heininger Holdings Hitch Lock # HE6001 is a proprietary type that only fits certain models of their bike racks.
  view full answer...


• Hitch Lock Recommendation for Hollywood Racks Bike Rack
  
• We have an anti-rattle hitch lock designed specifically as a fit for Hollywood Rack bike racks. For that you'd want the Hollywood Racks Threaded Hitch Lock # HRLHPT. The HitchMate hitch lock part # HE6001 that you referenced is designed for a different brand of bike rack and would not fit. The lock on the # HRLHPT would be easier to access though since it's perpendicular to the bolt instead. I attached a review video for this for you to check out as well.
  view full answer...


• Will HE6001 Hitch Lock Fit HE6000 Hitch Extender
  
• The Hitch Extender # HE6000 uses a standard 5/8 inch hitch pin so the Threaded Trailer Hitch Lock # HE6001 will fit and work perfectly.
  view full answer...


• Solution for Threaded Hitch Pin that Won't Thread into Bike Rack
  
• The anti-rattle device part # HE6001 that you referenced has been confirmed as a fit for your Advantage SportsRack glideAWAY Bike Rack. Most likely what is happening is that the threads of your bike rack are dirty or rusty and need to be cleaned out so that the bolt will thread into it. I attached a help article that details how to do this in a similar situation for you to check out. If the rack's original anti-rattle bolt still will thread into the rack then you will want to compare...
  view full answer...


• Hitch Extension and Locking Pin for a 2003 Honda CR-V with Spare Tire
  
• You'll have two options, depending on your hitch size. In either case, your overall tongue weight capacity will be reduced by 50% when the extender is installed, so you'll want to verify your hitch's capacity prior to purchase and ensure that you can still install your chosen rack and actually carry bikes on it. If your hitch is the smaller 1-1/4 inch size, you'll want to purchase Brophy's 6 inch 1-1/4 inch extender, part # HES6 in order to extend your hitch. This extender pushes the...
  view full answer...


• Available Anti-Rattle Hitch Locks for a Thule Parkway
  
• The correct part for your Thule Parkway is the Thule Anti-Rattle Kit, part # THSTL2 This will provide the best anti-rattle and lock for the Thule Parkway and is designed specifically for Thule racks. Locks like part # HE6001 will not fit correctly.
  view full answer...


• Hitch Extender for Use With a Pop-Up Trailer With a 2 inch Trailer Hitch Receiver
  
• Since it sounds like you don't need too much of an extension I recommend that you go with the shortest extension that we currently offer which is 11 inches long # HE6000. There is already a lot of play at the rear of a trailer due to the axle location. Adding an extender to the mix will only increase the amount of play that you will experience, so you will need to make sure that whatever you have on that rack can take a beating. You will also want to make sure that whatever accessory that...
  view full answer...


• Will HitchMate Threaded Trailer Hitch Receiver Lock Fit a Thule T2 Bike Rack
  
• Thule uses a propriety bolt pattern on their products. So the Hitchmate threaded trailer hitch receiver lock # HE6001 will not be compatible with the Thule T2 # TH916XTR-918XTR. However we do offer a Thule Snug Tite hitch lock and anti-rattle device that may work for you. The Thule Snug Tite hitch lock and anti-rattle device part # THSTL2 is a replacement lock system that is compatible with your 2 inch receiver hitch. I have included a video demonstrating the assembly of this Thule...
  view full answer...


• Recommended Hitch Lock for Saris Freedom 2 Bike Rack
  
• I do have a solution for you, however because of the unique thread design on the shank for your Saris Freedom 2 Bike Platform Rack # SA4412B, the HitchMate Threaded Trailer Hitch Receiver Lock # HE6001 that you referenced will not be compatible. For a threaded, anti-rattle hitch lock that will work with this bike rack, I instead recommend the Saris Anti-Rattle Hitch Lock # SA3022. This is confirmed to work with the Saris Freedom and will do a great job of helping to deter theft while...
  view full answer...


• Is the HitchMate Threaded Trailer Hitch Receiver Lock Compatibile with Yakima Hold Up Bike Rack
  
• The HitchMate Threaded Trailer Hitch Receiver Lock for 2" Hitches # HE6001 is not a confirmed fit for the Yakima Hold Up # Y02443. You will need the Yakima HitchLock for Yakima Hitch Mounted Bike Racks - Same Key System (SKS) # Y07235 to fit that system. Each manufacturer has a slightly different lock so they are not interchangable.
  view full answer...


• Will the HitchMate Threaded Trailer Hitch Receiver Lock for 2" Hitches HE6001 Fit a Thule Vertex
  
• HitchMate Threaded Trailer Hitch Receiver Lock for 2" Hitches Item # HE6001 is only tested and confirmed for Heininger bike racks. Some reported that it will work on a Thule rack but I can't guarantee it. For the Thule Vertex a lock that will work for sure is the Snug-Tite lock # THSTL2.
  view full answer...


• Hitch Lock Recommendation for Use with a SportRack Ridge Swing 4 Bike Rack # SR2415
  
• The threaded hitch lock you would want to use with the SportRack Ridge Swing 4 Bike Rack # SR2415 is the part # SR0901. The part # HE6001 that you referenced is designed for Heininger racks so I can't recommend it for you. This will replace your current hitch pin bolt with one that has a lock at the end of it.
  view full answer...


• Hitch Lock Recommendation for Sportrack Bike Rack
  
• Sounds like you are looking for a hitch lock for your Sportrack Bike Rack that uses a threaded hitch pin. We actually have exactly what you are looking for. For that you would want the part # SR0901 which is a threaded pin and lock confirmed to fit Sportrack bike racks.
  view full answer...


• How to Lock Rola TX-102 2-Bike Rack to Trailer Hitch
  
• I may have a solution for you, however the HitchMate Threaded Trailer Hitch Receiver # HE6001 is not compatible with your Rola TX-102 2-Bike Rack # 59400. This is because the shank on the Rola rack features a uniquely threaded hitch pin hole that will only work with the included threaded bolt. At this time Rola does not have a threaded hitch lock available that will work. To lock the bike rack to your vehicle, I recommend using a standard cable lock like the etrailer.com # e98891. You...
  view full answer...


• Can Different Brand Hitch Lock Be Used with Thule Roadway Bike Rack
  
• Thule, along with most other bike rack manufacturers, use unique threads in the shank's hitch pin hole that are designed to only be used with their own hitch pins/locks. Because of this the HitchMate # HE6001 you referenced won't be compatible. For your Thule Roadway 2 Bike Rack # TH912XTR the Thule Snug Tite Hitch Lock # THSTL2 will fit and work perfectly. If you wanted to add a cable lock as well to secure the bikes to the rack you can use the Thule # TH538XT or a standard cable lock...
  view full answer...


• Will The Heininger HitchMate Receiver Lock Work on a Yakima Hold Up Rack
  
• Since most bike rack manufacturers use proprietary hitch pins, universal fits like this Heininger HitchMate # HE6001 can't be confirmed to work but there is an alternative. Replacement Hitch Bolt and Clip for Yakima HoldUp # Y8890200 with the Yakima HitchLock # Y07235 will do what you want and is confirmed to fit the Yakima Hold Up Rack # Y02443. I have included video overviews for both of these products for more information.
  view full answer...


• Hitch Pin Lock Recommendation for Thule Bike Rack with Threaded Hitch Pin
  
• The threads of the HitchMate part # HE6001 are too large to fit a Thule bike rack. So what you'd need is the part # THSTL2 which is basically the same thing but designed for Thule bike rack applications.
  view full answer...


• Swagman XC2 Bike Rack Hitch Lock Recommendation
  
• For a locking hitch pin confirmed as a fit for your Swagman XC part # S64650 you would want the part # S64029.
  view full answer...


• Replacement Bike Rack For Reese Outfitter That Can Be Used on Camper
  
• The Reese Outfitter 4 is an older bike rack produced by Swagman which is now the Swagman Original 4 Bike Towing Rack for 2" Trailer Hitches part # S64675. The Swagman Original 4 Bike Towing Rack for 2" Trailer Hitches is rated for use on the back of Motorhomes but not campers or fifth wheels. If you need a bike rack for use on the back of a camper or trailer, I recommend Reese Eclipse 4 Bike Rack for 2" Hitches - Tilting part # 63124. This Reese bike rack can carry 4 bikes on the back...
  view full answer...


• How to Lock Bike Rack With No Hitch Pin Lock Available
  
• The HitchMate Threaded Trailer Hitch Receiver Lock for 2" Hitches # HE6001 has a 5/8" pin diameter and is designed for certain SportRack bike racks so it will not work for you. Hitch pin locks are designed for specific bike racks so if that's what you need it for, let me know what rack you have I can see if there is a lock that will work for you. Otherwise, if you have a 1/2 inch diameter hitch pin that likely means you have a 1-1/4 inch receiver and we do have hitch locks with 1/2 inch...
  view full answer...


• Recommended Threaded Hitch Pin Lock For SportsRack Bike Carrier
  
• For your SportsRack Bike Carrier and hitch receiver, I recommend the HitchMate Threaded Trailer Hitch Receiver Lock for 2" Hitches # HE6001. This threaded locking hitch pin has an overall length of 5-7/8 inches. The distance betwwen the lock and the head of the bolt is 3-1/4 inches. The threaded portion is about 2 inches. These measurements can be found in the attached video.
  view full answer...


• Hitch Lock for 1-1/4 Inch Trailer Hitch
  
• The issue is that threaded locks like the HitchMate # HE6001 are specific to certain accessories; in this case the HitchMate is certain Advantage bike racks. You never mentioned if you have a 1-1/4" or 2" receiver but it sounds like the 5/8" diameter the bolts is the problem from what I can gather, as opposed to the length, which would indicate you have a 1-1/4" receiver. We do not carry Solvit so there is no guarantee a standard lock will work but the Master Lock Trailer Hitch Receiver...
  view full answer...


• Can the HitchMate Threaded Trailer Hitch Receiver Lock be Used on the Hollywood Racks Sport Rider
  
• I would love to help but it sounds like you are trying to use the HitchMate Threaded Trailer Hitch Receiver Lock part # HE6001 on both the Hitch Extender part # HE18 and your Hollywood Racks Sport Rider SE2 part # HR1450Z. If that is the case then we do not offer any solutions that will allow you to do this. The first issue as you mentioned is that there would need to be a nut welded inside the hitch extender in order for the threaded hitch pin lock to work for you. The threaded hitch...
  view full answer...

Do you have a question about this Hitch Lock?