This hitch cover with a rotary-engraved, black and red Chevy Corvette C6 logo is perfect for any C6 enthusiast. The chrome-plated solid brass faceplate is paired with a rust-resistant stainless steel base. Locking bolt and foam gaskets included.
Features:
Specs:
Hitch covers are fun to show off and they look cool, but they do more than just accessorize your vehicle. This officially licensed Chevrolet Corvette C6 logo hitch cover helps to keep dirt out of your receiver and deters rust, so you can easily install ball mounts and other hitch accessories when you need them. This hitch cover is a great way to protect your receiver and express yourself, all in one.
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Today we're going to take a look at the Chevrolet Corvette C6 Logo Trailer Hitch Receiver Cover for two-inch trailer hitches. Now, this is an officially licensed Chevrolet Corvette C6 Hitch Cover. It's designed to slide into your two-inch hitch receiver to help keep out dirt, prevent corrosion. If you notice, it's a nice rotary-engraved Chevy Corvette C6 emblem with a durable UV resistant black and red epoxy fill. It has a chrome plated solid brass faceplate, which will add style to your vehicle. Does use a stainless steel base, which will help resist rust and corrosion. The length on the post is right at three and a half inches long.
Does come with the three different thicknesses of chrome gaskets to help eliminate rattle. You just pick the correct one that you need. Gives you a good fit on your vehicle. Put it on to the post, and then just slide it all the way towards the front just like that. It will give you a nice seal.
Does come with this nice locking stainless steel bolt and the two wrenches to help secure the cover to the hitch. All you have to do is these wrenches are triangular design, so they'll only fit that. You just put one on each side, and that will loosen it up, and then run that through there. When you tighten it down, it will lock it into place. It has such a design that unless you have these tools to get it off, it's going to be very to get off. Again, the application for this is two inch by two inch trailer hitch receivers.
Give you a few measurements on this. The total width on this edge to edge is six inches, and the total height bottom to top is three and a quarter inches tall. That should do it for the review on the Chevrolet Corvette C6 Logo Trailer Hitch Receiver Cover for two-inch hitches.
Average Customer Rating: 4.9 out of 5 stars (258 Customer Reviews)
This hitch cover with a rotary-engraved, black and red Chevy Corvette C6 logo is perfect for any C6 enthusiast. The chrome-plated solid brass faceplate is paired with a rust-resistant stainless steel base. Locking bolt and foam gaskets included.Great looking receiver cover. Fast ship ping.
The quality and finish are excellent as is the fit. I will definitely order from etrailer again with confidence.
Thank you for your follow on delivery and a great product.
I love my trailer hitch, however; I was involved in a rear end collision that almost bent the hitch into. I’m glad the hitch cover was on as it and the hitch sustained mist of the rear end damage to my SUV. That hitch cover was a strong one! I’ve ordered another one and I’m sure it will be just as good as this one, but I hope I don’t have another wreck to prove that point.
Review from a similar OEM in Hitch Covers
This is a recap of my first experience with etrailer.com and an order for the customized MKX Hitch-Cover. Please read through to the end; it's all good.
I placed my order and saw several shipping options with various price-points. Without any explanation of how long each would take or improve transit times, I picked Priority Mail.
Shortly, I received an email confirmation that it would "ship" in about seven days. Hmmm? I replied that I needed it DELIVERED in about seven days.
Within minutes, I get a response that it would be to their warehouse in two days and would be sent UPS Ground with assurance that would get it to me in two days. Michelle even credited back the difference between Priority and Ground. Nice.
True to her promise, the unit delivered in four days. Yea!
Not so fast, it didn't fit into my 2" hitch receiver. The insert was 1/8" too wide.
I sent photos of the unit sitting on a ruler to show the problem. Now, I was down to two days before my trip.
Michelle had her team pull units off the shelf and measure them. All were within spec, thankfully. A replacement unit was sent and arrived in the nick-of-time. She also provided a prepaid return label.
I love the look of my MKX Hitch-Cover! I loved the service and their commitment to me, a first-time customer. Wow!
Review from a similar OEM in Hitch Covers
I have a set of Rock Tamer mud flaps that attach to my Class V hitch using a reducer. This adds about an inch of overall distance to the pin. No one that I know of makes a hitch cover that fits a Class IV or V hitch, and no one makes one with a shank that is long enough to work with my setup. I researched all of the brands that etrailer sells, and found this LFI brand had some possibilities. With the shank being attached to the plate with screws, I should be able to make a spacer and make this work. I cut a 1" piece of a 2" square tube that I salvaged from a piece of an old 5th wheel landing gear, and added it to the shank. I drilled a new hole in the shank and now have a hitch cover that I can use with or without my mud flaps. It would be great if I could get a longer shank from etrailer or from LFI preferably with no holes so I could custom drill my own, or with pre-drilled holes to my specification. Short of that, my solution works very well for my needs. Once again, etrailer came through, it just took a couple of hours of extra work. I am very happy with my final product. One other comment on the Class IV and Class V hitch. I like the "locking" pin that was included with this cover, however it is too short to work with the Class IV or V hitch. I wish they would supply a pin that is long enough to work with the hitch this particular cover would ultimately be used on.
Review from a similar OEM in Hitch Covers
I have a 2020 Chevy Silverado LTZ silver ice metallic. With advanced trailering package a Chevy bow tie light messes all the sensors in the rear of the truck. Anyways I looked for something else I found this Chevy Silverado hitch cover from you people. It is the best hitch cover I have ever seen, it is beautiful looks great on my truck or any Chevy I am very fussy it is better than anything I could buy in any automotive store I will buy more for my other chevys. PS. Make sure you lock it on receiver so no one will take that is how beautiful it is here is a picture of it
Review from a similar OEM in Hitch Covers
Hitch cover came in Ford OEM packaging stating that it was for a 2" hitch. However, original order was for an 1-1/4". Contacted eTrailer.com customer support. They checked the part number, and told me to open package. The cover was, indeed, for an 1-1/4" hitch.
Did have an issue with securing the locking pin to the hitch. Had to remove 1-3/8" material from one of the locking wrench keys (These 2 keys have a specially cut triangular bit). This allowed me to secure the locking pin/cover.
eTrailer Customer Service is the best. They are very courteous, as well as, knowledgeable and helpful. The product is 1st Class Ford OEM, and am very happy with the purchase. Would definitely purchase from them again, and recommend them to a friend.
Review from a similar OEM in Hitch Covers
Ordered my first Ranger hitch cover and excited about putting it on...Thanks for such great service.
Review from a similar OEM in Hitch Covers
Bought this hitch cover my 2020 Ford Explorer and it looks great, product is also rust proof so it should look great for many years. have included a photo of hitch cover, however because it is chrome plated it shows a lot of reflections.
Review from a similar OEM in Hitch Covers
Solid, good looking chrome hitch plate. Installs quickly with a heavy bolt and rubber gasket. It was rapidly shipped, highly recommended vendor and product.
Review from a similar OEM in Hitch Covers
Very well made. The problem is all F450 have a 3in Hitch the stainless Steel Bolt that you send with the receiver is not long enough to work some one needs to review the problem. Thanks
Review from a similar OEM in Hitch Covers
Only thing i thought you can do on your website was when ordering something put how long it will take to make it or to say not in stock but it take this long make and to get delivered to you but hitch was very nice looking can't complain about that so on that i gave excellent and it came packaged real nice and safe thanks for what your company did and i would order from you guy's again
Review from a similar OEM in Hitch Covers
I have been looking high and low for a new trailer hitch cover for my MKX. The original cover was plastic and broke about a year ago. The one I ordered is a good metal material and should last a long time. Placing the order was easy, and it arrived right on-time! Great job.
Review from a similar OEM in Hitch Covers
The cover is beautifully made and was easy to attach to hitch. The car looks complete! I was impressed at how well the cover was packaged for shipping- no chance for dings or scratches. Will definitely share this site with friends and neighbors. A satisfied customer.
Review from a similar OEM in Hitch Covers
Well made and looks great.
Review from a similar OEM in Hitch Covers
I ordered a chrome trailer hitch cover. Katie D. was extremely helpful. She kept me informed of the progress of my back order, and also answered my questions about the product. I asked if the chrome was warranted against rust. She said she would find out and sure enough the next day I received an email from her saying it was. You have great products, great service, and great workers. I'll order again.
Review from a similar OEM in Hitch Covers
I had this for over a year and I will say without hesitation,it looks as good as the first day I installed it!!! Very high quality, I still get compliments on it.
Review from a similar OEM in Hitch Covers
Like the fact the hitch cover is solidly made - prefer metal over plastic every time . Looks great on my explorer.
Four stars because installing wasn’t that easy because of tight space between hitch pin and bumper.
Review from a similar OEM in Hitch Covers
All Metal Construction.No Plastic...Which is exactly what I wanted.OEM Product.Packaged very well and installation was very simple Highly Recommend..Pictures Posted Below
Review from a similar OEM in Hitch Covers
After a year it looks like new.
Review from a similar OEM in Hitch Covers
Very heavy duty. High quality. Nice addition for my truck.
Review from a similar OEM in Hitch Covers
The hitch cover is AWESOME!! It arrived in a timely fashion, was easy to install, fits snuggly and looks !! This product is great!!!!
Review from a similar OEM in Hitch Covers
Excellent Customer Service and helped me get my Product in a timely manner due to the initial Product I ordered was not available in Stock but got me an identical Product that was.
in Stock.
Review from a similar OEM in Hitch Covers
I was very pleased with the hitch cover. It is very well made and s reasonable price. I received the item quickly. Everything was easy to order and getting it on its way
Review from a similar OEM in Hitch Covers
It was for my husband and he loves it
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.