Use this anti-rattle clamp to keep your hitch-mounted accessory from rattling and wobbling in your receiver. Tightening the 2 bolts pulls the accessory shank against the hitch wall, keeping it stable and quiet. Durable steel construction.
Features:
Notes:
Average Customer Rating: 4.4 out of 5 stars (145 Customer Reviews)
Use this anti-rattle clamp to keep your hitch-mounted accessory from rattling and wobbling in your receiver. Tightening the 2 bolts pulls the accessory shank against the hitch wall, keeping it stable and quiet. Durable steel construction.Was a quick fix for wiggly clanking problem I had took about 3 minutes to install works great
I didn't think it was going to work when I first tried it, but realized that I was putting it on backwards. I knew my hitch was noisy but WOW. This thing completely stopped all the clanking and rattling.
This is an awesome product and works extremely well! No rattles at all from my PWC trailer! This company has always been extremely good to buy from with my hitch, wiring harness and now this anti rattle device.
Clamp works great, the two screws ensure a tight fit and no rattles.
I’m very glad I bought it. Only two things wrong with it. 1 it’s made in China. 2 if you have a drop hitch like I do, you might have to cut a notch in the bottom where the gusset hits the clamp preventing the stinger from going in far enough to insert the hitch pin. Other than those two things it works great. My hitch has NEVER been quieter and stable. Very satisfied with the results.
Darren - 06/04/2019This is a simple yet effective device to stiffen a receiver mounted device reducing or eliminating any slight wobble. However, my GMC receiver has a welded bead around the outside (presumably to reinforce) and I have to regularly tap the device back and re-secure the bolts. This may be unique to GMC.
Works great. No more noise when I pull the trailer empty. TY
Your product has a couple of structural defects: 1. With the bolts on the bottom, when the vehicle goes through a dip in the road, the bottom of the bolts grinds on the road. Your bolts are too long. 2. With the bolts on the bottom, when I went through a dip in the road and they scraped the asphalt, the result was a broken weld. Having China make your product is not a good idea. 3. With the bolts on the bottom, the tips of the bolts are about 1 3/4" below the bottom of the vehicle's receiver. The bolts should be on the top. But that is not the way the setup is pictured. So I like your product's potential, but not the way it is engineered or designed.
Rachael H - 05/08/2019I think it’s a great little invention, The only change I would make… In fact I did make that change is to change the bolts from a zinc plated to stainless steel. After all, it’s gone just sit outside all the time. But other than that, it’s perfect
doesn't fit very well on my ford factory hitch with a weld on the edge keeps slipping off.
Product is simple and effective...... performs as described. Only consideration is if there is a substantial "bead" of weld at the end of the receiver tube since this is where the bolts will bite into when tightened and if the bead is large enough, it presents a rounded surface rather than a flat one for the bolts to bite into potentially causing a "walking" situation.
Steven - 04/29/2019Third one I have owned. Works well if placed and tightened in the right location.
Don H - 08/17/2020Bolts need to be back farther so they are behind the metal lip around reciever
Looks like a good product but it did not fit on my 2018 Jeep Compass. Could not install it with bolt side down because the part of the Jeeps hitch where you attach safety chains to where too close to the receiver opening. I could only install it with bolts on top, but even then, it could fit over the receiver very well. The bolts were on the outer lip of the receiver and gauged the lip pretty good because it has a rounded lip instead of a flat lip. Not happy about that, but it did prevent rattling for the trip however, it looked like it was about to fall off. I ordered something else and will not use this one on my vehicle again.
I have a double hitch installed on my Class C motorhome for my bike rack and my Blue Ox to tow the car. I installed 2 of these and they completely eliminated all the movement in the assembly. I also added a Quiet Hitch Pin for the top receiver that did not have a lip. It also works perfectly. Thanks for great products!
My hitch has a lip on the edge that makes it impossible to guarantee it will not vibrate off. The bolts tighten onto the lip instead of behind it, where it would work best to keep it from vibrating anywhere. Depending on the trip distance and trailer load weight it sometimes remains in place the entire time. Until I find a better one I will keep using this.
Product seems well made, solid and seems to holding the hitch receiver steady - no more knocking or bike rack wobbling coming from the back end! Will update after further use. Fast shipping and great service from etrailer as always!
Just on of those things you just have to have. Locks my Cargo Rack soilded to my hitch. Traveling down the the road you can't feel the rack moving at all. Well made and easy to install.
I am verry happy with the Product. It take a bit to get used to it on mounting it to the welded ring on the hitch to keep it from sliding off. Ones installed, it will keep the Bike Racke from ratteling.
It has been a great addition to my Jeep Wrangler for carrying extra cargo when traveling. It is easy to assemble and install.
Not happy. Unit did not fit my Jeep Grand Cherokee properly. Not enough clearance with the way it's designed. As a result of did stay hooked up properly came off and bolts vibrate it out first time I used it. haven't touched it since then. I'm sure if you didn't have the fitment issues with the design of the hitch it would work fine.
Very easy to install and remove. Solves rattle problem with hitch. Excellent service and fast shipping.
The unit itself is stout, The threads were a little messed up (touched up with a file), and works great. The only issue I had was with my truck and the way the chain hook up works (they are round and stick out very far) which makes this harder to use. I'll most likely have to grind the edges to make it fit, but this is no fault of the unit, just the truck. most new trucks are really making the hitch's low profile and these may present a challenge. Again for the price, and build, it's a great unit.
Does not work on my John Deere Gator HPX615E. Neither front or rear receiver. Pay close attention to how your receiver is made One star was given not for product quality but to warn others that it may not be suitable for certain applications and it’s the purchasers responsibility to verify before ordering. .
Heather A - 06/28/2018Do you have a question about this Hitch Anti-Rattle?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Helpful Link
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.