To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Replace the 7-way, RV-style trailer connector on your with this T-One harness. ModuLite reduces strain on wiring system. Brake controller adapter splices into your 's wiring when installing your electric trailer brake controller.
Features:
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the tail light assemblies to access this harness. Once you've plugged in the T-connector, run the body harness up to your car battery and connect the wires per the included instructions.
Once installation is complete, the 7-way connector will be stowed beneath your vehicle, near the trailer hitch. A mounting bracket (sold separately) is recommended to keep the connector secure.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 7-pole connector itself - to help prevent corrosion.
A ModuLite power module is built into this T-One connector. Because most trailers run on a 2-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's 3-wire system need to be combined so they are compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
This adapter splices into the 4-pin connector on your vehicle's built-in brake control wiring harness. The harness is located to the left of the steering column, through a grommet in the engine compartment.
This adapter is designed to plug directly into your electric brake controller after splicing into your vehicle's wiring. You can unplug and remove your brake controller at any time and securely stow it away.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (14 Customer Reviews)
Replace the 7-way, RV-style trailer connector on your vehicle with this T-One harness. ModuLite reduces strain on wiring system. Brake controller adapter splices into your vehicle's wiring when installing your electric trailer brake controller.The kit, along with the video on how to install it, works fabulously. The videos are just gold to a DIY-er like me. Beware of how difficult Ford makes it to get to the tail light wiring, though. The video shows installation of the kit in a cargo van, where the tail light access turns out to be fairly simple, but the passenger version requires removal and displacement of multiple panels and the floorboard. I have added some photos to illustrate for my 12-passenger 2018 Transit 350 XLT. I will say that this etrailer solution is MUCH cheaper and less intrusive than trying to use the factory-installed system. It turns out that even if you have the wiring installed, and I think *all* models have the harness to at least the rear axle, it still takes reprogramming the computer, replacing the center console, installing a controller, and losing your cup holders, in addition to buying the remaining wire harness, etc. It took me about 4 hours to complete.
After installing the wire harness that only took a few hours I put it to use and in the past year have had no problems with it. The instructions were very well done. I am very pleased with this product.
Customer service was above exceptional. Couldn’t find the right connector for vehicle and Bailey found it! Great employee and knows the products
Installed on a 2016 Transit 350. The quality of this kit is pretty good, but there are two things that are problematic. First and most important, the connectors for the factory harness to do not line up with the actual Ford factory connectors in the taillights. I had to cut off one side of the prongs that should slide into the factory connector. Be sure to check first as only one of them is off - line it up and it will be obvious which one is off. Second, if installing this on a Transit without a factory harness there is no way for you to attach the 7 pin outlet. Does not come with the metal bracket to attach the outlet to your bumper. The length of the socket isn't going to allow you to really drill a hole and mount in the socket in the plastic. Last, there is a small box that goes in the drivers side cavity at the rear tailight that also has a ground wire attached. The length of the ground wire pretty much means you need to place it at the bottom of the cavity. They could lengthen that 6 inches so you can zip tie it high up in the cavity, but this is minor compared to points 1 & 2 above. Pay attention to the diagram for insetting the wires into the socket. Really easy as long as you orient it properly. They click in so don't force them - twist until it lines up. In the end it is cheaper than the Ford harness and a bazillion dollars less than letting Ford install it.
Installed as expected with the exception of a missing part. I thought it was all inclusive but the bracket for the 7-way plug is not included. Got to the end of the install and realized it was missing and had to go back and order the bracket. Not a big expense but wish it was included so project can be completed.
Great people to deal with, helpful and knowledgeable, great prices, delivery, what more can you ask for from a company today???
Thank you very much. You guys are awesome. Also, video tutorials are really helpful.
We ordered our trailer lighting kit on a Monday had it shipped over night and received early Tuesday. We had the trailer working properly in 2.5 hours. The kit was easy to install and everything worked perfectly.
Since we Installed Brake controller, We have towed the boat across the country without any issues. Installation was simple.
I was a five star everything was Great
Easy to install in my driveway. Works perfectly. Excellent phone experience during the purchase process.
GREAT PRODUCT - TIMELY SHIPPING -EVEN FOR BACK ORDERS GREAT CUSTOMER SERVICE
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.