Install a 4-way trailer connector on your vehicle without cutting or splicing into your wiring. Zero-contact interface sensors identify the current flowing through each wire by simply clamping onto it. Circuit-protected module is made using SMT.
Features:
Specs:
This revolutionary wiring method makes it fast, easy, and safe to add a 4-way connector to your vehicle so you can power your trailer's lights. Unlike traditional tail light wiring harnesses, which either splice into your vehicle's wiring or plug into designated ports in your factory harness, this system bypasses your vehicle's wiring entirely. Just clamp the intuitive sensors onto the individual wires of your OEM tail light harness and let the ZCI system do the rest.
Zero-Contact Interface Sensors
Each zero-contact interface (ZCI) sensor included with this harness is able to read the current that travels through the wire it is clamped onto. Upon sensing the specific modulation of that wire, a signal can be sent along the wire that connects the sensor to the included 4-way flat trailer connector. That signal is then transmitted through the connector to activate the appropriate function on your trailer lights.
Universal, Worry-Free Design
No Splicing, Cutting, or Connecting to Factory Wiring
Because the ZCI sensors can read the signals sent through your vehicle's wires just by clamping onto them, no cutting or splicing is necessary. The system completely bypasses all of your vehicle's wiring. As a result, your trailer's lights will be powered without overloading your vehicle's electrical system. And there is no chance of damaging feedback either.
When using this ZCI harness, you don't have to worry about voiding your warranty, nor do you need to be concerned about any potentially damaging errors on your part if you're not an experienced do-it-yourselfer. And if you have a vehicle that doesn't allow certain modifications - like a leased car or truck - you can install this harness and remove it later with no obvious alteration to the vehicle.
Maximum Compatibility
This wiring harness is universal. You can use it on any vehicle that operates on a 12V, negative ground system. Because installation is so simple, you can easily remove the unit and transfer it to another car or truck at any time.
In addition, the ZCI sensors are able to read the signals sent by multiplex wiring systems and systems with pulse width modulation (PWM) and low-side-switched wiring, making the harness compatible with nearly all automotive wiring systems. This unit also works with both standard incandescent tail light bulbs and LED bulbs.
Built-In Tail Light Converter
Most trailers run on a 2-wire system - wherein the brake and turn signals are carried on a single wire. Many vehicles, however, are built with separate brake and turn signals. This type of system is referred to as a 3-wire system. If your vehicle operates on a 3-wire system, it will need to be converted so that it will be compatible with the wiring system of your trailer. This is done by adding a tail light converter to your wiring setup to combine the brake and turn signal functions of your automobile so that they run on a single wire to properly activate your trailer's tail lights.
This ZCI unit has a tail light converter built in to ensure proper functioning with any vehicle that operates on a 3-wire system. If your car has a 2-wire system and therefore does not need a converter, don't worry. The method of installing the sensors will take into account the wiring configuration of your vehicle so that only the necessary sensors are used, making sure the appropriate signals are sent back to the 4-way.
Installation
This universal harness connects to your vehicle's tail light wiring harness. To connect, just follow the included instructions. There are 4 ZCI sensors included. Each sensor has a colored label on it. Depending on your application, you will need to connect all or some of these sensors to the factory wires indicated in the instructions.
To get the power necessary to operate, the harness must be connected to a 12V power source. The included installation kit provides the hot lead required to connect this module to your car battery. When all connections have been made, connect the hot lead to the black wire on the ZCI power module and run the other end of the lead up to your car battery. Connect the hot lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery. Then insert the included 15-amp fuse into the fuse holder.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location either within your cargo area or beneath your vehicle, near the trailer hitch. If you choose to mount the connector near your hitch, a mounting bracket (sold separately) is recommended to keep the connector secure.
It is also recommended that you use a small amount of grease on all electrical connections on the 4-pole connector to help prevent corrosion.
Surface Mount Technology
Each ZCI wiring harness is built using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability, and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? SMT components also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
California residents: click here
Average Customer Rating: 5.0 out of 5 stars (4 Customer Reviews)
Install a 4-way trailer connector on your vehicle without cutting or splicing into your wiring. Zero-contact interface sensors identify the current flowing through each wire by simply clamping onto it. Circuit-protected module is made using SMT.I'm extremely happy with this wiring harness for my 2013 BMW X3. I first purchased the Heavy Duty Modulite kit but since the wires in my model year car were so small the adapters you snap onto each wire couldn't make solid contact in any way. I had to return this kit which etrailer was very understanding about. I highly recommend purchasing this upgraded kit since it's to easy to click the sensors closed to tap into the wire's currents. The kit has not tripped the ECU or any other "alerts" in my car's system warning software that (a foreign) electric part has been installed. I had a few questions for their tech support and Pete was very professional and took the time to clarify some of the wires I would be targeting for installation which made it all the more efficient and easy to do. I have towed a boat we have numerous times and the harness has worked flawlessly....it was definitely worth it to step up to this kit for the snap on sensors alone. Thanks etrailer ! Best Regards, Ford I
Looks great only took about two hours to install hitch and trailer pigtail
everything as advertised as it should be.
Not advertised was the excellent service and every attempt to get my product to me on a tight time schedule.
Above and beyond, but just what I want to do for my clients.
Really great service!
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.