T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
(201 reviews)
Price: $81.03
In Stock
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
Item # 118420
Our Price: $81.03
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (201)
- Q & A (0)
- Photos
Tekonsha Custom Fit Vehicle Wiring - 118420
- Custom Fit
- Trailer Hitch Wiring
- 4 Flat
- Converter
- Tekonsha
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Circuit-protected converter guards against shorts.
Features:
- Provides a 4-way flat trailer connector at the back of your vehicle to power your trailer's signal lights
- Compatible with 5-pole, 6-pole and 7-pole adapters (sold separately)
- Connects quickly and easily - no cutting or splicing of wires
- Locate connection points in trunk
- Plug in T-connector
- Includes circuit-protected tail light converter to ensure that your vehicle's wiring matches that of your trailer
- Provides protection against electrical shorts and overloads
- Constructed of 16-gauge bonded wire
- Comes with dust cap for 4-way flat connector
Specs:
- Maximum amperage:
- Stop/turn lights: 2.1 amps per circuit
- Tail lights: 5 amps per circuit
- 1-Year limited warranty
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk, behind the tail lights on both the driver's side and passenger's side. You will need to remove some interior trim or carpeting to access the harness.
Once installation is complete, the 4-way flat connector will be stowed within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
Circuit-Protected Tail Light Converter
A tail light converter is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. The tail light converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
This converter safeguards itself and your vehicle against possible electrical shorts and overloads with integrated short circuit protection. Just install the connector as indicated and rest assured that the wiring system of your vehicle will remain feedback-free.
118420 Tow Ready T-1 T-Connector - 4 Wire
Installation Details
This Product Fits The Following Vehicles
- 2004 - 2009 Mazda 3
- 2004 - 2005 Mazda 3
- 2010 - 2013 Mazda 3 Hatchback
- 2010 - 2013 Mazda 3 Sedan
- 2006 - 2013 Mazda 3 without LED Taillights
- 2008 - 2012 Honda Accord Coupe
- 2008 - 2012 Honda Accord Coupe
- 2008 - 2012 Honda Accord Sedan
- 2008 - 2012 Honda Accord Sedan
- 2006 - 2015 Honda Civic Sedan - excluding Si and Hybrid
- 2006 - 2015 Honda Civic Sedan - excluding Si and Hybrid
- 2012 - 2012 Honda Civic Sedan - Si models
- 2009 - 2014 Honda Fit
- 2007 - 2014 Honda Fit
- 2007 - 2008 Honda Fit excluding Sport
- 2007 - 2008 Honda Fit Sport
- 2007 - 2012 Mitsubishi Galant
- 2009 - 2010 Acura TSX
- 2009 - 2010 Acura TSX
- 2011 - 2014 Acura TSX Sedan
- 2011 - 2014 Acura TSX Sedan
California residents: click here
Customer Satisfaction Score:
98% were satisfied with this product
2% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
- Alternate product found
Customer Reviews
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 118420
Average Customer Rating: 4.9 out of 5 stars (201 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring - no cutting, splicing or tapping required. Circuit-protected converter guards against shorts.by: bambooburgler06/16/2023
2009 Honda Accord
A [online] search & subsequent [online] video on your channel led me to this purchase. Extremely high-quality, extreme ease-of-installation, I couldn't possibly be more pleased with this product & company. Highest recommendation possible!! :)
by: Eric Kelly09/23/2022
Great company. I am now sending you a picture of my Honda Civic, which I use to tow my teardrop camper. Thank you.
by: Trials Warrior10/09/2012
2012 Mazda 3
After watching the installation videos I was a little concerned about how to route the power wire to the car battery. It turns out this wiring harness doesn't need a power wire. No need to cut/split wires either. Just unplug the connector from the rear light assembly, plug it into the wiring harness female connector and then plug the wiring harness male connector back into the light assembly.
The whole process took me about 45 minutes.
This went on a 2012 Mazda 3 hatchback with regular light bulbs.
by: ORDER HERE OR PAY MORE AND THEY DO IT ALL RIGHT TH11/03/2020
Best harness for a car I ever bought and works perfect. I bought the hitch also an installed myself as I have before. Video helped me removed parts under this newer Civic so it was simple. Best customer service too because I had ordered the wrong riser for the hitch ball and the woman called me to tell me an re-did the order so it all arrived right and showed up in about 4 days !! Amazing company to say the least an was not my first purchase by no means. AAA+++
by: Charles C08/20/2013
Easy installation even with the previously installed remote braking system I installed to use the Fit as a tow behind our RV. I don't think it took 20 minutes start to finish.
by: Alex H. 01/04/2017
2010 Mazda 3
Bought this product about a year ago and still working immaculately. Couldn't be more pleased! Hookup was simple and diagram was very explanatory. Would reccomend to anyone! Thanks, eTrailer!
Alex H.
1/6/2018
A year later and my lights still work flawlessly and wires are still in new condition. Couldn’t be more pleased!
by: Stephen 09/30/2023
2009 Honda Fit
Very happy with the hitch
by: Tom03/24/2022
Arrived quickly,and installed quickly and easily. I'm a satisfied customer.
Tom M.
3/24/2023
Still working dependably. Its a good idea to use electrical grease to resist corrosion and to keep good electrical contact of mating plugs.
by: Daniel 08/14/2023
so far good. fast delivery
by: Gabriel R.04/17/2017
2012 Honda Civic
Bought this at the same time I bought my hitch and hitch bike rack. figured if I was installing a hitch I might in the future haul a trailer and would need lights. later bought a hitch mounted cargo rack and added lights. boxes would cover or block my tail lights of my car, so I added lights to the cargo rack. Works great. Thank you.
Gabriel R.
4/18/2018
I couldnt be happier with all my purchases. I use the Bike Rack frequently and have used the trailer hitch to tow a trailer once so far. Maybe Ill get to use that a little more this year also. Love the purchases.
by: Mike C.08/26/2015
Honda Civic
The wiring harness was simple to install, but only after watching your video at Etrailer.com. The printed instructions were somewhat lacking. My Honda Civic has 4 light bulbs in each taillight. Instead of the instructions telling me to look for the brown wire, why not just show a simple diagram of the 4 bulbs and say "connect the yellow wire to bulb A(see diagram)? I got it connected and it works well. My kit did not come with the double sided tape to secure the box in the trunk. It came with a screw, but I was not willing to drill another hole in the car. Double sided tape works well.
Mike C.
8/25/2016
No complaints. Lights come on when they are suppose to. Thats all I can expect from a harness.
by: Shawn P.11/09/2012
2010 Mazda 3
Install went off without a hitch (no pun intended). I jacked up the car, threaded the fish wire, all in all pretty simple. I actually did it on my own and it went well. I was under the car an braced the bar up, was able to get one of the nuts on and put the other two on to hold it into place while I finagled the other side into place (the passenger side outlet on the muffler was kinda in the way). I was able to get it on easily but tightening the last nut (closest to the back of the car) was a bit tough because the hitch frame gets in the way. Overall, it was simple, it's all tightened down, and now we can tow a trailer/cargo/whatever!
Thanks etrailer, your prices beat anyone on the internet and Uhaul by at least 100 bucks.
Shawn P.
6/9/2014
Actually thanks to you guys, much cheaper than Uhaul and other sites, the install was easy and everything worked well and we ended up towing a trailer from LA to Milwaukee when we moved, on a Mazda 3! So, yeah, pretty happy with it, now we can do things like put an attachment on for bikes or camping equipment or whatever.Thanks for the follow up, thats good customer service
by: Max06/03/2020
Thanks Nicole for helping me out getting everything squared away!
Quick shipping all the way up to central Alaska!!!
Already mounted took no time at all!!!
A+
by: Chad09/16/2014
2008 Honda Civic
A competitor wanted to charge me $70 to install a similar product on top of the price of the wiring harness. I purchased this product for under $50, watched a video showing how it is installed on my exact vehicle, and spent 10 minutes installing it. It works perfectly. I couldn't be happier. A+ for etrailer!!
Chad
9/28/2015
Thank you for following up with me. I couldnt be happier one year later with our purchase. The hitch and wiring for the trailer work perfectly and I would not hesitate to purchase from you again and have already recommended your site to others. I was very impressed especially with the videos that allowed me to see how installation should go before I even ordered. This is a great feature. Thanks again for great service!!!
by: KC03/26/2017
2008 Honda Fit
This took me about 30 minutes to install. I had never installed tow wires before but this kit was very easy. The hardest part was determining where to plug it in to the car's light system but the plugs fit well and no soldering was required.
Kc
3/26/2018
I remain very pleased with the hitch and wiring harness and have recommended etrailer to friends!
by: Mark 08/06/2022
2009 Honda Accord
The wire harness worked great simple to plug in and go. I watched a video of installation and once I got into actually installing the harness it was super easy. Great quality and no cutting and splicing. Awesome product.
by: Jeff05/13/2022
have bought 2 "plug n play " wiring harnesses from etrailer and am very pleased with my purchase. Very easy to understand instructions and easy to install and durable
by: Chris05/15/2022
2010 Honda Fit
Super easy to install! Honda Fit 2010 - ultra easy, the connectors fit exactly as needed. The length of wire for inside the car was adequate. Took only about 20 minutes to install. Highly Recommend this unit for your Fit. Super happy, this was the easiest light harness install ever, and I like that I don't have to splice into the original wire harness, this could be replaced or come out at any time.
by: Tom 04/27/2021
These are great. I used to spice wires. Never again, these are truly plug and pay and are worth every dollar. This is the fifth one I have installed for friends and family.
Tom
4/28/2022
The new plug and play wire harness are great and easy to install. I only buy these product from etrailer because of their support.
by: John09/03/2022
Perfect fit! installation video spot on, quality wiring harness
by: Tim G08/04/2013
2008 Honda Accord
I bought a draw-tite receiver, wire kit and ball for my 08 Accord... everything fit great and had great communication with etrailer folks. I was totally satisfied with service, delivery, quality and
performance of my product.
I'm buying from them again soon for our new Acura MDX
Tim G.
2/2/2015
The Honda is sold, but no complaints!The MDX hitch has performed flawlessly....
by: Billy J Broome09/16/2016
2006 Honda Civic
I received my trailer harness by US postal mail on the third day after I ordered it.
It took less than twenty minutes to install. Simple and easy. Most importantly it was the right harness for my 2006 Honda Civic.
Billy B.
10/18/2017
Custom Fit vehicle trailer wiring is doing great. Works every time I hook it up. Thanks.
by: George06/08/2019
Install of wiring was fairly easy, made harder because I'm way worse at this than I think I am. Hardest part was figuring a place to stick the module, and finding something to stick it with. Box says it comes with double sided tape, but mine, at least, did not. Best to have some sticky stuff on hand just in case my experience is the norm, and not the exception.
Literally just unplugging wires and plugging them back in, but in a better, more different configuration. Lights work. I know because I tried it.
The wire the 4-pin connector is on is long, but maybe not long enough? It's long enough for my use case, but I can definitely see a longer trailer tongue or a shorter trailer cable causing an issue. A longer cable would be nice, but I'm sure a 4-pin extension would suffice as well.
Every other cable/wire is more than long enough, so no issues with getting it across the trunk of the car to the other brake lights.
4 stars, because of the lack of included (per the box, anyway) double-sided tape and a just-barely-long-enough cable could be a foot longer and stop worrying me. Quality otherwise is good.
by: Frank05/29/2019
2014 Honda Civic
Installed hitch and wiring harness in a 2014 Civic sedan. Be very sure to specify exactly the correct car when ordering since the fitments are very specific--as I found out when I ordered a harness for a Civic without being sure to get a sedan's harness instead of a coupe's! E-trailer was very good to immediately send me the correct harness and accept back my erroneous order.
The hitch is a two-person installation. I did it by myself with an extreme amount of effort to hold the muffler out of the way while threading the attachment bolt above the muffler. Three hands are essential--or else a lot of wood blocks and fine-grained metal bending. Once attached it is a very solid hitch and it is nearly invisible below the back end of the car. Yet the hookup has plenty of access for a trailer.
by: Mark04/15/2018
2010 Honda Accord
Hitch and wire harness hooked up easy to do picked up trailer yesterday works awesome thank you
Mark M.
4/17/2019
Great easy to install
25
201
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- Trailer Lights Do Not Work when Running Lights are On with Wiring Harness 118420, 2008 Honda AccordMost likely there is a bad ground, a short, or an overload condition. First check the ground at the converter box and make sure it is attached to a clean bare metal surface. Then do the same for the main ground on the trailer side. And finally do the same for the lights on the trailer. Ground issues normally show up when there is more load on the harness. That could be why it only shows up when the vehicle lights are on. To check for shorts you will need to inspect the wiring on the trailer...
view full answer... - Recommended Wiring Harness for a 2010 Honda Civic It'll still work. The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118420 plugs into your Honda's factory wiring harness behind the fenders. It doesn't connect anywhere along the trunk so replacing your factory trunk with one that has an extra brake light won't effect installing this wiring harness. The T-One Vehicle Wiring Harness item # 118420 is confirmed to fit the 2010 Honda Civic sedan models. I have linked an installation video below to help you get...
view full answer... - Do I Need A Converter To Install Trailer Wiring on My 2008 Honda FitYes, your 2008 Honda Fit will need a converter to install trailer wiring on the vehicle. The Honda Fit has turn signals separate from the brake lights and requires a converter to convert the cars 5 wire system down to the trailers 4 wire system. The converter is also circuit protected and protects your vehicles sensitive electrical system from damage if there is a short or mis-wire on a trailer you hook up. The correct wiring harness for your 2008 Honda Fit is part number 118420. Simply...
view full answer... - Best Trailer Wiring Harness Recommendation for a 2012 Honda FitThe Tow Ready Wiring Harness part # 118420 has been custom fit to your 2012 Honda Fit so that it will install much easier than a universal kit. There would be no taillight circuits that would need to be cut or spliced (which could easily get damaged), or any guess work as to which wires to use. This harness just plugs in-line with your taillight connectors and will be ready to go. I would recommend the # 118420 because it will be easier to install and will be much more reliable than a...
view full answer... - How to Install Trailer Wiring Harness on a 2010 Honda Civic SedanYou are in luck. Since your 2010 Honda Civic Sedan is not a SL or Hybrid model, you will not need to install a 12-volt power wire up to your battery. All you will need is the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector, # 118420. The Tekonsha wiring harness is an easy install with no cutting or splicing of wires. All the wiring hook-ups will be at the rear of your Civic and plug into existing wiring plugs on your vehicle. I have linked a video on how to install...
view full answer... - Why does My Cruise Controll Shut Off On My 2008 Mazda 3 when I Use The Turn SignalsI spoke with my contact at the manufacturer and this problem has occurred before but is unusual. The first thing to do is make sure that the ground wire on the T-One wiring harness, item # 118420, is not connected to a common ground and that it is connected to its own separate ground connection. If that does not solve the problem then the converter may be providing feedback to the brake circuit and the harness will need to be replaced. If you need to replace the wiring harness and you...
view full answer... - Installing Trailer Wiring Harness 118420 on a 2008 Mazda 3 HatchbackThere should just be two little doors, one behind each tail light on your 2008 Mazda 3 hatchback, that you will open to get access to the tail light connectors. I have included a link to the installation details for wiring harness # 118420 for you. There are some pictures in the instructions that should help. I have also linked 2 videos that should help.
view full answer... - Trailer Wiring Harness Recommendation for 2012 Honda Civic SedanFor trailer wiring for your 2012 Honda Civic the best available harness is the part # 118420 which is a confirmed fit. The T-One brand harnesses are our most reliable ones we carry so I recommend them the most.
view full answer... - What are the Functions of a 4 Flat Trailer Connection on a 2009 Honda FitYes. That is what a 4 pole connection does. The 4 pole on the trailer connects to the vehicles 4 pole connection and the vehicle provides the same functions as the taillights for the vehicle and trailer. So you will have left and right signals, and brake lights. The last wire (white) is ground. The wiring for your 2009 Honda Fit is a little different as it has brake lights that are separate from the turn signals. The Tow Ready Custom Fit Vehicle Wiring, # 118420, is the correct harness...
view full answer... - Will Wiring Harness 118420 Fit a 2006 Mazda 3 Grand TouringMy contact at TowReady confirmed that the 2006 Mazda 3 Grand Touring models have differently shaped connectors than the standard models, so the # 118420 wiring harness would not be able to be installed on your vehicle. I recommend using taillight converter # 119130 to wire your vehicle for towing. I have included a link to the installation instructions for the converter.
view full answer... - Which Wires To Re-Connect 4-Way Flat Vehicle and Trailer ConnectorOn the 4-way connector, Green will be right turn and brake, Yellow is left turn and brake, Brown is tail or marker lights, and White is ground connection. If you need to replace the trailer side connector, you will need 4-Pole Trailer End Connector, part # 18004. If you need to replace the vehicle side connector, you will need Tow Ready Wiring 4-Pole, part # 18002. You will use the included connectors and connect the wires color for color. I have linked an FAQ on wiring the shows the...
view full answer... - Will the Draw-Tite 24816 Hitch Fit a 2004 Mazda 3 Sedan?The Draw-Tite Sportframe Trailer Hitch Receiver item # 24816 fits all models of the 2004 Mazda 3 including the sedan. I have linked an installation video and the instructions below. I took a look at these instructions and there are no differences in the installation method between the sedan and hatchback models. If you need a wiring harness for your Mazda 3 I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector item # 118420. This harness will provide...
view full answer... - Trailer Wiring Harness for 2013 Honda Civic SedanMy contact at Tow Ready tells me that the connectors that join the wiring harness to the tail light assemblies are different in the sedan, versus the Civic coupe model which is why the # 118437 wiring harness you mention is not compatible with your Civic Sedan. You'd want to use the # 118420, unless you have a Hybrid model in which case you'd use # C59236. We have an install video showing the # 118420 being installed on a 2012 Civic, you can view it by clicking the provided link.
view full answer... - Is An Extra Converter Needed When Wiring The 2009 Honda Fit With The Tow Ready Harness # 118420The correct wiring harness for your 2009 Honda Fit Sport is the Tow Ready T-One Vehicle Wiring Harness, part # 118420. It will include the circuit protected taillight converter that is needed on your Honda Fit. You will not need any other converters or electrical parts to have a 4-flat connector on your vehicle. The Honda Fit has turn signals separate from the brake lights and requires a converter to convert the cars 5 wire system down to the trailers 4 wire system. The converter is also...
view full answer... - Trailer Wiring Harness Recommendation for 2015 Honda Civic SedanThe trailer wiring harness I recommend for your 2015 Honda Civic sedan is the T-One kit part # 118420 which is a confirmed custom fit. Of all of the wiring kit brands we carry this one is the most reliable so I recommend it the highest.
view full answer... - Trailer Wiring Recommendation for 2005 Mazda 3 Hatchback with LED TaillightsWe've had the chance to install the Tekonsha trailer wiring harness part # 118420 on a very similar Mazda 3 hatchback with LED taillights to your 2005 model so it would fit and work great. Check out the install video link I attached on this page as well.
view full answer... - Trailer Wiring Harness for 2010 Mazda 3 Without LED Lights But Trailer DoesYou are correct that the wiring harness designation has to do with the vehicle lighting and not the trailer lighting. This has to do with the source power coming into the converter. Since you don't have LED's in your 2010 Mazda 3, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118420. This will connect perfectly with your car and will not have issue with a trailer that uses LED lights. I've attached a video of this installation to assist.
view full answer... - Tow Bar Wiring Kit for 2009 Acura TSXFor tow bar wiring for your 2009 Acura TSX you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring to allow your tow vehicle to control the taillight assemblies of the towed vehicle. This comes with a round 6-way connector that you will install on the front of your towed vehicle and enough coiled wire to go from there to the RV.
view full answer... - Where Does Wiring Harness 118420 Plug Into on a 2012 Mazda 3The yellow, brown, and red refers to the wires on harness # 118420 for your 2012 Mazda 3 sedan. The wire colors used on the vehicle will not likely be these colors because there isn't a standard color code for automotive wiring. You will just need to locate the matching connectors on the driver's side that will accept the connectors with the red, brown, and yellow wires. The green wire and its connectors plug in line with the passenger's side tail light wiring. I have linked a video that...
view full answer... - Recommended Wiring Harness for 2010 Mazda 3 and Determining if Vehicle Has LED Tail LightsThere are a few different ways to determine if your 2010 Mazda 3 Grand Touring is equipped with LED tail lights. The best and most sure way is to simply contact or visit your local Mazda dealer with your vehicle's VIN. They will be able to tell you with certainly what your vehicle is equipped with. You can also remove the tail light housing and look for the bulbs themselves. An incandescent bulb will look like your standard bulb while an LED will have diodes. Another way is to observe...
view full answer... - Trailer Wiring Harness Needed For 2013 Honda Civic CoupeI do have an option for the coupe but the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118420 fits the 2013 Honda Civic Sedan. The wiring harness needed for the 2013 Honda Civic Coupe Excluding SI and Hybrid, is the Tekonsha T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118437. This wiring harness plugs into your vehicle's wiring located behind the driver's-side and passenger's-side interior trim panels in your rear cargo...
view full answer... - Is Drilling Required When Installing Draw-Tite 1-1/4 Inch Hitch # 24776 On 2007 Honda FitThere is no drilling required when installing the Draw-Tite Class I 1-1/4 Inch Hitch, part # 24776, on a 2007 Honda Fit. It is a bolt-on application. I am including a link to the installation instructions on the Hidden Hitch. I am including a video link of a Curt trailer hitch being installed on a 2006 Honda Fit. The hitch is a different brand, but the installation is the same as the Hidden Hitch. Some items you may need to complete your Class I towing setup are the Tow Ready 2 Inch Hitch...
view full answer... - Headlights Do Not Work On 2012 Honda Civic After Installing T-ConnectorYou will want to check the wiring connections and make sure the ground wire is secure on your 2012 Honda Civic. You will need to check each of the pins in the connectors on the vehicle side of the connectors to make sure they have current using a circuit tester like part # PTW2993. I have attached a helpful article that shows how to troubleshoot 4 and 5-way wiring installations. Since you said all the lights work but the headlights are you referring to the vehicle turn and brake lights...
view full answer... - Towing Hot Dog Cart with 2008 Honda FitAssuming that the cart is a trailer equipped with lights and is capable of being towed, what you propose might be possible. The weight of the cart seems to be well within the capabilities of the hitch, but you will need to check with your owners manual or Honda to ensure that the vehicle can be used for towing. I cannot recommend anything that would contradict the vehicle manufacturer recommendations. If Honda does not prohibit using the vehicle to tow your cart, you will need to wire...
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Test Fit:
Joe V
Test Fit:
Nicholas E
Test Fit:
Shane T
Test Fit:
Hayden R
Test Fit:
Shane H
Test Fit:
David F
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Jacob T
Video Edited:
Andrew L
Video by:
Andrew K
Video by:
Kathleen M
Video by:
Alan C
Video by:
Jonathan Y
Video by:
Jacob H
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
Installed by:
Cole B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Ed S.
1/17/2013
Awesome, im going to grab the same setup for my 2012 Mazda3 S sedan.