To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your Jeep Wrangler 4xe with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the trim access cover, scuff panels, and tail lights to access these connection points. Once you've plugged in the T-connector, run the hot lead to your car battery, which can be found in your trunk on the passenger's side. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (35 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.This harness was a simple plug and play. . Hardest part was running positive wire to the front to the battery. No easy on a fat boy. But got it. Only complaint was the green wire with harness to the passenger side needs to be at least a foot longer. I actually added 2 feet on mine and gave me plenty of room to work. Great product th
Ordering from Etrailer is always easy and customer service is above par always. I have NEVER had a bad experience when calling fir assistance on a particular part or placing an order.
I do enjoy watching the videos prior to doing an install to assist with any questions that might have arose while in the process. The system Etrailer has us top notch!
It has performed very well and the excellent installation video was all that was needed to install the frame hitch and wiring kit. The Curt wiring kit, as your tech explained has just enough wire to be long enough to make the plug into the tail light. If you fail to know that in advance it is easy to route the wiring where it would not reach. This was by far the easiest frame mounted receiver style hitch and wiring kit we have installed so far. The height of the Jeep frame allows the entire installation of hitch and wiring to be done without the use of our wheel ramps. Let me touch on an issue that William mentioned, the use of a Swagman platform wheel mount hitch on a Jeep with spare tire mounted in the center of the tailgate on newer Wranglers. This position creates two challenges whether you use the Allen style top tube support style or the one I we installed. The Allen style require the backup camera to be relocated as the bike rack center pillar will obscure it, the Swedman wheel mount style requires use of a 2" to 11/4" extension plus the wheel brackets must be removed and turned upside down to allow the spare tire and tailgate to open completely. Lastly, IMHO all Swedman racks with 1 1/4" mounting frame should be supported with a cable under tension at the highest position possible to relieve the forces created by bicycle weights within specs. As e-assist bikes become more popular it is very easy to exceed the design weight of rack construction. Even two Huffy beach cruiser bikes that are within rack weight design put a lot of stress on this style rack. Not going to debate this issue, had a failure of the center support 1 1/4" beam years ago with significant damage to the two road bikes when beam structurally collapsed.
Excellent transaction! They are my go to for anything for my Jeep
Was not a direct fit
I'm still waiting for a refund on the one that was wrong that I had to reorder a new part and pay for it so I'm still waiting for money back
Super easy wiring job if you have a crawler. The instructions on the etrailer site made the entire thing a breeze. Still working great a year later.
Best pricing, easy fit, easy installation (the videos are excellent).
Definitley my G0-To place for everything for towing and trailers!
Easy to install and fits perfectly on my 22 Jeep Wrangler. Works as expected.
Delivered timely easy and easy install
Arrived on time, product was as describ ed.
Easy install, took my time and it went well, no complaints
David
8/30/2024
No issues one year later
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Victoria H.
11/25/2024
Hi William, I'd like to get a little more detail on how this wasn't a direct fit. I have linked the installation video and at about the 6 minutes mark you can see this harness will connect to your taillights. Does your plug resemble the one in the video?
Helpful Links
https://videos.etrailer.com/static/images/video/Install-CURT-Custom-Fit-Trailer-Hitch-Wiring-2023-Jeep-Wrangler-4xe-56407.webm