To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your Hyundai Palisade with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the trim access covers to access these connection points. Once you've plugged in the T-connector, run the hot lead to your car battery, which can be found in the engine compartment on the driver's side. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
Average Customer Rating: 4.8 out of 5 stars (49 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.I installed the harness yesterday with no problems at all. After the installation I hooked up to a small utility trailer and all functions worked properly.
Installed on a 2024 Palisade. It works well. The most difficult part was running and concealing the power feed from the battery compartment back to the rear of the vehicle.
Worked perfectly, and was a seamless setup and installation.
I thought the return process was right pricey. I got a hitch and harness delivered in two days on ups which was great! Sadly the replacement part took much longer as it went USPS. I was in a hurry
I’m a 77 y/o man. I installed the trailer hitch and wiring harness on my 2024 Hyundai Palisade with the vehicle on the ground. My wife helped by handing me things while I was under the vehicle. I first watched the etrailer how-to videos and installation was fairly easy. After dropping the muffler, I placed the hitch over the tail pipe and used a foot stool to support the hitch on the muffler side while I loosely installed the bolts on the driver side. The only difficulty I encountered was removing the muffler hanger near the side of the vehicle. Thank you etrailer for your videos.
Prompt and courteous service. Just what I needed. No hassles. Will always look to etrailer for my trailer needs.
Happy with the product. the only problem was at the box was pretty banged up. Lost some paint on the actual hitch. And it was a shame because I really want the product to arrive during the following mid week. End up having to stay home after I found the out the process going to be coming in that Friday. I was told they'll be coming in mid week by the sales person.
Saved me at least 2 hours doing the job. Installed the hitch and wireing in 3 hours. Saved 400
Worked well
It’s been about a year and the part is still holding up in great condition.
Amazing service and friendly people
Ground screw provided doesn't tighten
Excellent product!
Easy to install
Good to do business with...
The video Mack’s it so easy
Easy to install. Installed as advertis ed.
Quick delivery and very professional customer service represenatives.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Emo
10/26/2024
The wiring harness was very easy to install. Works just fine!!