7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End

See what our Experts say about this Hopkins Custom Fit Vehicle Wiring

• Parts Needed To Add Hopkins 7/4 Pole Connector To a 2020 Ford F-150 With Factory 4-Way
  I have a couple ways you can install the 7- and 4-Pole Trailer Connector Socket # HM40975 on your 2020 Ford F-150 with a 4-way flat factory connector. The first is going to be the easiest but is more costly. You will use the harness from the Curt 7-Way # C56413 and connect to the connector you found. The Curt harness will connect to the factory wiring as seen in the installation video I have linked near the bottom of the page. Otherwise we do have the Hard Wire Connector # 20147 which...
  view full answer...
• 2023 Honda Passport Plug-And-Play Style Trailer Wiring Kit Recommendation
  Thanks for reaching out, Robert! The best way to add a plug-and-play style 4-Way/7-Way connector to your 2023 Honda Passport is with the following parts: - Curt T-Connector Vehicle Wiring Harness # CU86FR - 7- and 4-Pole Trailer Connector Socket # HM40975 - No-Drill Mount Bracket, Long # 18136 The Curt wiring kit is a plug-and-play style where the only "splicing" you have to do is ground the white wire to a clean bare metal spot on your frame with the included self-tapping screw....
  view full answer...
• Recommended 7-Way and 4-Way Trailer Wiring Connector Compatible with Factory Harness
  For your 2002 Ford F-250, the wiring harness you are seeking with both 7-way and 4-way connectors is the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way and 4-Pole Flat Connectors # C55774 or the Reese # 74682. Either of these will connect to your factory wiring harness to give you both of the trailer connectors you seek.
  view full answer...
  
• How to Activate the Factory Trailer Towing Package on a 2000 Chevy Silverado
  The wiring will already be run on your 2000 Chevy Silverado. There will be 1 of 2 wiring situations on your truck. The wiring for the 7-Way will be located above the spare tire. If it is just bare wires with no plug, you will need to hard wire one in. The harness we have for this wiring situation is Pollak 7-Pole, RV-Style Trailer Connector Socket w/ Wiring Harness and Mounting Bracket, # PK11898. If your truck has a plug, then you will need to use a connector like the Replacement Multi-Tow...
  view full answer...
• 7-Way Wiring Configuration for Slide-In Truck Camper
  Your slide-in truck camper does not have electric brakes so the blue brake circuit wire from its 7-way connector is not used. All other lighting functions as well as 12V auxiliary power will be maintained on the other circuits. Please refer to the linked photo for the standard wiring/function configuration for RV-style 7-way connectors.
  view full answer...
  
• Installing 7-Way and 4-Way Connectors on a 2015 GMC Acadia
  The Hopkins # HM40975 that you referenced plugs into a US Car Connector (see attached picture). This typically will replace a factory 7-Way on a vehicle so if your 2015 GMC Acadia didn't come with a 7-Way you might not have that connector. If it does exist though it will be located somewhere around the trailer hitch. If you don't have the US Car Connector but you would like fully functioning 7-Way and 4-Way connectors then we do have a solution for you. Simpy install the T-One Vehicle...
  view full answer...
  
• Recommended Trailer Hitch for a 2020 Ford Ranger
  The trailer hitch that I recommend for a 2020 Ford Ranger is the Curt Trailer Hitch Receiver part # C13417 which is a custom bolt-on fit that does not require any cutting or drilling. The process should actually only take you around 20 to 40 minutes. I have attached an install photo for you as well. For a trailer wiring harness, the T-One Vehicle Wiring Harness part # 22124 is your best option as it does not require any splicing therefore is almost entirely plug and play. I also recommend...
  view full answer...
  
• Is There a Difference Between Hopkins 7 and 4-Way Kits 40974 and 40975
  Basically they are the same connector with just a slightly different part number. We carry the part # HM40975 and if you ordered the 40974 from someone else (not recommended haha) you'd get the same thing which just a different part number on the box. I attached an install video for this kit for you to check out as well.
  view full answer...
• Troubleshooting Danger Notification and No LED Light on Curt Echo Brake Controller
  Sine the LED does not light up on your Curt Echo # C51180, that means there's no power getting through to it. Given the fact that the Echo was receiving power and working properly at one point, chances are you're dealing with a poor ground issue. I would start by checking the power and ground circuits on your Ram's trailer wiring. These will be on the 1 o'clock and 7 o'clock positions, as shown in the attached diagram. You can use a 12V probe-style circuit tester, like # PTW2991 to check...
  view full answer...
  
• Location of Factory Wiring Connector for 2021 Ford Explorer Limited
  Hello Ken; what wiring harness are you trying to install? Do you have the factory tow package on your 2021 Ford Explorer? If you don't have the factory tow package there won't be a wiring connector at the rear of the vehicle. If you have the factory tow package there will be a plug behind the bumper that attaches to the # HM40975. If you do not have the factory tow package you need to install the Curt 4-way # C56093 which plugs into the connection points in the rear cargo area as seen...
  view full answer...
• Installing a 7-Way Trailer Connector on a 2013 Ford E-250 Van
  I checked with Tow Ready about 7-Way connector # 118261 and it is not a confirmed fit for the 2013 Ford E-250 van. Since there are no other options and since you have some factory wiring already, I recommend using 4 and 7-Way connector # HM40975 with harness # PK11998. You will need to test the wiring on the vehicle end with a circuit tester such as # PTW2993 to determine the functions. Then you can install the harness accordingly: Red - Left Turn and Stop White - Ground Blue - Electric...
  view full answer...
• How Does Trailer 12 Volt Accessory Circuit of 2019 Ford F-150 7-Way Activate
  The 12 volt accessory circuit on your 2019 Ford F-150 activates in a pretty unique way. You first have to connect the trailer to the truck and then using the dash display let the truck recognize the trailer. Also once this is done the circuit is still only active when the vehicle is in drive. Or you could bypass all of that and run your own wire for this circuit with 10 gauge wire like part # 10-1-1 (sold by foot) through a breaker from the positive battery post to the 1:00 pin of the 7-way.
  view full answer...
• Troubleshooting Electric Trailer Brake System on Trailer Towed by Chevy 2500 Series Truck
  Discovering why the trailer brakes are not getting power will be a process of elimination. I am not aware of what you have and have not checked, so I will describe the whole troubleshoot process. Start with the brake controller itself. Is it properly adjusted and leveled (if necessary) according to the instructions? Is it getting power? To determine if the controller is receiving power, you can use a circuit tester like part # PTW2993 on the black wire that feeds the controller to ensure...
  view full answer...
• 7-Way Wiring Harness Installation on a 2004 1500 Chevrolet Silverado
  You can use the Pollak 7- and 4-Pole Trailer Connector Socket, item # HM40975, if you are replacing an existing 7-way connector on the rear of your 2004 Chevy Pickup. If you need to install the 7-Way connector for the first time the factory connection point is going to be on the left side of the vehicle above the spare tire. If there is a plug on the end of the wiring harness located above the spare tire, it will simply plug into the rear of the HM40975. If the harness ends in bare wires,...
  view full answer...
• Does Hopkins 7-Way # HM40975 Fit 2017 Ford Explorer
  The Hopkins trailer wiring 7-way part # HM40975 that you referenced is a fit for your 2017 Ford Explorer and will attach directly to the wiring of the vehicle without any additional wiring. Basically it plugs right in to the round connector behind your rear bumper and you'd be set.
  view full answer...
• Wiring For 7-Way Connector on 2004 Chevrolet Silverado 2500
  On your 2004 Chevrolet Silverado 2500 the factory wires should be light green, dark green, blue, yellow, red, brown, and black. The functions of those wires should be as follows: light green - reverse lights dark green - right turn/brake blue - electric trailer brakes yellow - left turn/brake red - 12-volt power brown - running lights black - ground I would also recommend testing the functions of your wires with a circuit tester, part # PTW2993, to verify the function of the wires on...
  view full answer...
• All LED Lights on Trailer Work Except Running Lights When Hooked To 2008 Chevrolet Silverado
  There are a few possibilities and things you will need to check on your trailer and your vehicle. You will want to start by checking the ground wires on the lights, make sure each light has a good ground connection to clean metal surface. Then, you will want to check the wiring on the trailer, start at the 4-way connector and visually inspect the wires for any cut or exposed wiring. If you find cut or exposed wiring where the protective coating on the wiring is missing, you will want...
  view full answer...
• Troubleshooting Damaged Trailer Wiring Connector on 2002 Ford F-350
  If the in-bed 7-Way on your 2002 Ford F-350 was damaged then you likely need to replace the entire wiring harness with something like the Hopkins # 41157. It would be best to inspect the connectors for any damage as well. As far as fuses go, if you turn to page 162 in your copy of the owner's manual you should see that the fuses in locations 6, 38, 101, 115, and 305 are for the various trailer functions. Aside from this if you're still having issues you'd need to take your pickup to a...
  view full answer...
• Troubleshooting GMC Truck that Left Turn Signal on 7-Way Stopped Functioning
  Since you have isolated the problem down to the left turn signal on the 7-way on your vehicle the problem is most likely a blown fuse under the hood of your 2006 GMC Sierra 3500. GM vehicles tend to blow fuses easier than the other manufacturers. Check the fuse box under the hood of your engine on the driver side for the trailer related circuits and replace as needed. I attached a couple help articles for you to check out as well.
  view full answer...
• Parts Needed to Add 7-Way to 2017 Jeep Wrangler with 4-Way
  Hey Chester, to convert the 4-way of your 2017 Jeep Wrangler to a 7-way you would want the part # 37185 unless the trailer has brakes. If the trailer does have brakes you'd instead need the part # ETBC7 with a brake controller like the P2 part # 90885. There isn't a direct plug in 7-way option that fits your Wrangler unless it came with a 7-way already.
  view full answer...
• Trailer Hitch and Wiring for a 2020 GMC Acadia
  We have everything that you need to start towing with your 2020 GMC Acadia! I recommend using the Draw-Tite Trailer Hitch # 76023 because it mounts behind the rear bumper and has a very clean look with the lower panel removed. Then for wiring I recommend pairing the T-One # 118276 with the Hopkins # HM40975 which gives you a plug and play wiring kit with both 4-Way and 7-Way connectors. I have linked installation videos of the trailer hitch and wiring on a 2019 Acadia that you can reference. To...
  view full answer...
  
• Replacement 7- and 4-Way Trailer Connector Socket for 2011 Ford F-150
  The 7-way plug you are referring to on your 2011 Ford F-150 is the same thing as the 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket # HM40975. This will fit as an exact replacement for the factory 7-way on your truck. I have added a link to a video review and install of this connector for you to check out as well.
  view full answer...
• Adding 7-Way Trailer Connector to 2008 Honda Ridgeline
  If your 2008 Honda Ridgeline came with a factory installed 7-Way trailer connector it is possible that # HM40975 will fit. You need to look at the wiring harness that plugs into the back of the factory 7-Way. If it looks the same as the back of # HM40975, see picture, then you can use it. If your Ridgeline did not come with a 7-Way then to add one you will start by installing a 4-Way (unless the truck already has one) using # 118400. Then you will need to install 4- and 7-Way installation...
  view full answer...
  
• 7 and 4-Way Trailer Wiring Connector Recommendation for 2015 Volkswagen Tiguan
  The connector you sent in a picture of is the standard 7-way connector that the Hopkins part # HM40975 is designed to fit. If you plug the # HM40975 into that connector you'll have both a 7 and 4-way trailer wiring connector active.
  view full answer...
  

Do you have a question about this Custom Fit Vehicle Wiring?