Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector

See what our Experts say about this CURT Custom Fit Vehicle Wiring

• Do You Have To Disconnect the Battery to Flat Tow a 2015 Ford Fiesta?
  To Flat Tow your 2015 Ford Fiesta, you will need to disconnect the battery and your key will remain in your vehicle while in the off position. Complete instructions are found in your owners manual on page 152 under Recreational Towing. "Note: There must be battery power to properly move the transmission’s internal components to neutral in step 3. Also, moving the gearshift to the neutral position without first turning the ignition to the on II position limits the towing capability to...
  view full answer...
• Trailer Wiring Recommendation for a 2014 Ford Fiesta Hatchback
  Since the 2014 Ford Fiesta Hatchback has a different taillight setup than the Sedan model you would need to order a wiring harness with a converter built into it like the part # C56191 that you referenced. The # 56047 that you referenced would not be the correct kit for you.
  view full answer...
• Recommended Hitch and Wiring Harness for a 2006 Buick Lucerne
  I am not sure what you mean by design but I have listed the parts below that you would need to set your 2006 Lucerne up to tow a trailer or use an accessory like a bike rack or cargo carrier. I have also linked an installation video and picture to show you what this hitch looks like installed. If you're not looking for a hitch and wiring harness then go ahead and email me back with a more specific description of what you mean by design. Draw-Tite Trailer Hitch Receiver item # 36309. This...
  view full answer...
  
• Lighting to Tow a 2015 Ford Fiesta ST Behind a Motor Home
  Trailer wiring harness # 56047 is for a 2015 Ford Fiesta sedan. But the ST is a hatchback so the harness will not fit. For a hatchback you would use # 118641. Another issue is that you would not use this type of harness to tow the Fiesta behind the motor home. This harness is for a Fiesta to tow a trailer behind it. It does not work in reverse so you need a different lighting solution. Since there aren't any plug in tow bar wiring harnesses for the 2015 Ford Fiesta ST at this time, your...
  view full answer...
• Trailer Hitch Recommendations for a 2008 Buick Lucerne Base Model, Special Edition, or Super
  In order to determine if your 2008 Buick Lucerne is a standard model CXL or a special edition, there are a couple of things you can do. If the driver seat is a power memory seat that remembers your settings and your tires are size 245/50R18, then you have a special edition. But the definitive way to determine the trim level of your Lucerne is to contact a local dealer and have them run the VIN number of the car and they will be able to tell you for sure which one you have. The Curt Trailer...
  view full answer...
• Hitch Recommendation for a 2015 Ford Fiesta
  Yes, we do carry hitches that are confirmed to fit your 2015 Ford Fiesta. If you have hatchback (excluding ST) then you would want the Curt Hitch part # C11067. If you have a sedan you would want the Curt Hitch part # C11369. For a ball mount you would want the part # C45521, pin and clip part # F-4, 2 inch ball # A-82, 1-7/8 inch ball # A-82. If you have a sedan you would want the part # 56047 for trailer wiring. We don't have a fit yet for the hatch models yet.
  view full answer...
• Can a 2006 Buick Lucerne Tow an 800 Pound Trailer without a Transmission Cooler
  According to the owner's manual for the 2006 Buick Lucerne it has a gross trailer weight capacity of 1,000 pounds maximum. It does not say that a transmission cooler is required. However, a transmission cooler is always a good idea, especially when towing, to keep the fluid cooler so the transmission is less likely to get damaged or wear out any faster than normal. If you do decide to install a cooler the most popular option for models with the 4.6 liter V8 is # D13503. And we also recommend...
  view full answer...
• Parts Needed to Convert Trailer to Electric Drum Brake Operation
  It is possible to have brake flanges welded to an axle that does not have them, but this requires specialized jigs that ensure perfectly correct alignment. Any errors in the orientation of the brake flange can cause all sorts of issues with brake performance and brake wear. This is not a typical DIY kind of project. Often when converting a no-brakes trailer to electric drum brakes it is far easier and often also more cost effective to simply replace the axle with one that includes brake...
  view full answer...
• Parts Needed To Flat Tow a 2015 Ford Fiesta Behind a Motor Home
  A plug in tow bar lighting system is not available for your 2015 Ford Fiesta but there are other options that will work. You could use a magnetic light kit, # RM-2120, a bulb and socket kit, # RM-155, or a diode kit, # 154-792-118158. The magnetic light kit will be the most cost effective option and the least permanent. The diode kit is the most involved of the installations and requires splicing into the vehicle wiring for installation. The bulb and socket kit bypasses the vehicle wiring...
  view full answer...
• Parts Needed To Transport Wheel Chair with 2008 Buick Lucerne
  I do have a hitch option for your 2008 Buick Lucerne to transport a 500lb electric wheelchair, but it will require a trailer as your vehicle is not rated for the amount tongue weight that a carrier would have. What you'll need is the following parts: Hitch # C12044 Ball Mount # C45520 Hitch Ball # C40001 Hitch Pin and Clip # F-4 Wiring Harness # 56047 and a small trailer like the Detail K2 # K2MMT4X6 To be able to use an actual carrier like # FHG69ZR you'd need to have a full size SUV...
  view full answer...

Do you have a question about this Custom Fit Vehicle Wiring?