Bulldog Square Jack - Drop Leg w/ Non-Spring Return - Sidewind - 26" Lift - 10,000 lbs

Ask the Experts about this Bulldog Camper Jacks

• Availability of Side Crank Trailer Jack with Removable Handle
  Most of our sidewind trailer jacks have handles that can be removed. For example, Bulldog sidewind jacks, like # BD182415, and Pro Series sidewind jacks, like # PS1400960376, are attached by a vertical clevis and pin. Other sidewind jacks, like Fulton F2 # F1413100334, have handles that can be removed by removing the 4 screws on the top and the top cap. There is a roll pin that holds the handle in place and you will need to use a center punch and hammer to tap it out so that you can...
  view full answer...
• Trailer Jack Dimensions for Bulldog Square Drop Leg Jack # BD182415
  The Bulldog Square Jack - Drop Leg w/ Non-Spring Return - Sidewind - 12-1/2 inch Lift - 12,000 lbs, item # BD182415, is lowered by using the Sidewind crank, sold separately, item # BD800090. The spring pin on the innermost leg is pulled to extend the foot down before lifting a trailer to reduce the amount of cranking needed to lift the trailer, and to extend the height that the jack will be able to lift the trailer. There are 5 positions for the spring pin that are 3-1/2 inches apart...
  view full answer...
• Electric Landing Gear Set Needed for Holland Trailer
  It looks like you have a landing gear set that is similar to the Bulldog 2-Speed Tandem Landing Gear Set # BD500154. I do have a solution for you to have an electric landing gear set but unfortunately we don't have a kit that will fit your landing gear. Instead you will need to replace your current landing gear like the Bulldog 2-Speed Jack # BD183416 and # BD182415. To convert these to electric you then simply need to add the Bulldog Powered-Drive Kit # BD1824180100. These have a weld-on...
  view full answer...
• Tubing Size and Comparison to Bulldog Jack for Pro Series Jack PS1400960376
  The outer tubing width of the Pro Series Jack part # PS1400960376 is 4 inch by 4 inch similar to the Bulldog part # BD182415. These jacks are essentially the exact same as they are both made by the same company and are made to the same specs. The advantage to the Bulldog is the 5 year warranty whereas Pro Series only has a 1 year warranty.
  view full answer...
• Diagram of a 10k Bulldog Landing Gear Jack for Gear Replacement
  To access the gears inside of the heavy-duty Bulldog jacks, like part # BD182415 to install the # BD500250 you simply remove the screws that are holding on the plate covering the top of the jack. Once that plate is removed, the gears, pins and handle should be exposed. Check out the diagram I attached to see how all of the parts come apart and go back together.
  view full answer...
• How to Access the Gears for the Heavy-Duty 12000 lb Bulldog Jacks
  To access the gears inside of the heavy-duty Bulldog jacks, like part # BD182415, you simply remove the screws that are holding on the plate covering the top of the jack. Once that plate is removed, the gears, pins and handle should be exposed. We also offer the Replacement Screw and Nut Kit, # BD500217, for the heavy-duty 12,000 lb capacity Bulldog jacks. I have attached two photos that show the inner workings of the heavy-duty Bulldog jacks for you to check out. The cross shaft...
  view full answer...
• Recommended 2-Speed Tandem Jack Setup with 12000-lbs Capacity
  It sounds like you're looking at something similar to the Bulldog 2-Speed Tandem Landing Gear # BD500154 and are trying to determine whether or not the 2-speed operation also works when an electric motor is used. The answer to your question is-yes; the motor does operate at 2 different speeds because of the 2 separate gears on the motor and jacks. However if you're just upgrading the motor, you won't be able to operate the 2 different speeds unless your jacks also have dual gear boxes to...
  view full answer...