Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs

Ask the Experts about this etrailer Camper Jack
Do you have a question about this Camper Jack?

• Can etrailer Landing Gear Replace Landing Gear On 2007 Montana Fifth Wheel Trailer
  
• The etrailer Landing Gear Set, part # RVLG-8000 can be used to replace the landing gear set you have on your 2007 Montana. The hand crank is available as a separate item and is part # RVLG-HDL. Most landing gears are interchangeable but you can take a quick measurement to make sure this works for you. The weld stops measure 15-1/2 inches inside to inside and 17-1/2 inches outside to outside. For a landing gear with a manual crank included you can order part # RVLG-8HDL. You can...
  view full answer...


• Are Replacement Parts for Atwood Landing Gear Available or Will Another Brand Fit
  
• The division at Atwood that handled the jacks and landing gear was sold off to Lippert so direct replacement parts are not available. But it is likely that the gear box and motor of another brand will still fit. And yes, the gear box and motor do just sort of hang there. Gear box # RVLG-RDBOX is one possible option. With it you can use motor # M1230. For the driver leg D shaft there were 3 possibilities for Atwood landing gear depending on which model it is (standard duty, heavy duty,...
  view full answer...


• Replacement Follow Landing Gear Leg for 1998 Fleetwood Savanna 5th Wheel
  
• I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the bevel gear inside your jack leg is the only one that is damaged then you can just obtain the Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060. However, if you don't want to mess with repairing your old jack leg or...
  view full answer...


• Replacement Landing Gear for a Keystone Laredo 5th Wheel Trailer
  
• Bulldog Tandem Landing Gear Set # BD500162 is a great option for a manual set to replace the landing gear on your Keystone Laredo. I have linked a video review for you. The handle is not included so use # BD500203 to add the crank handle. For an electric set you could use # RVLG-8HDL and add motor # M1230 and, if you don't already have one, a switch # LC145236.
  view full answer...


• Dimension Needed to Determine if Etrailer Landing Gear RVLG-8000 Fits Trailer
  
• The etrailer Landing Gear Set, part # RVLG-8000 can be used to replace the landing gear set you have on your trailer most likely. Most landing gears are interchangeable but you can take a quick measurement to make sure this works for you. The weld stops measure 15-1/2 inches inside to inside and 17-1/2 inches outside to outside. For a landing gear with a manual crank included you can order part # RVLG-8HDL. You can add a motor to this landing gear. You would just need part # M1230.
  view full answer...


• Replacement Landing Gear for 2010 Keystone Fuzion FZ322 Fifth Wheel Trailer
  
• There is a way for you to determine the correct replacement landing gear for your 2010 Keystone Fuzion, though we do not have landing gear made specifically for your trailer. Instead, you will need to measure the mounting brackets on your trailer from outside to outside like in the attached diagram and choose the amount of lift and weight capacity that will work for you. For example, you may be able to use the Landing Gear # RVLG-8HDL, which has an 8,000 lb capacity, offers 20-1/2" of...
  view full answer...


• Replacement Landing Gear Needed for Part # VMC900R-304103
  
• If you are looking to replace your landing gear then I have a possible solution for you, we just don't carry any sets with the part VMC900R-304103 that you referenced. Our Landing Gear Set # RVLG-8HDL is rated for 8,000 lbs and has 20-1/2" of travel. This set comes with a manual hand crank, but if you are wanting for your landing gear to be electric then you need the 12V DC Motor # M1230 as well. To determine if this landing gear set is compatible with your 2008 5th wheel you simply...
  view full answer...


• Solution for Needing Replacement Landing Gear for 2013 Starcraft Travelstar 278 BHS w Atwood 71125
  
• Since Atwood is no longer in the landing gear business it is basically impossible (unfortunately) to get just a replacement leg. The part number that you gave me actually is a document that shows the various parts for Atwood landing gear, but nobody has information as to what those replacement parts are the equivalent of. Because of this I recommend replacing the landing gear on your 5th wheel trailer. This gives you some peace of mind that you won't have to replace any parts in the...
  view full answer...


• Repair Kit for Atwood Landing Gear Leg
  
• Atwood was sold to Dometic a few years back and replacement parts for older landing gear are scarce. We do still have Stromberg Carlson Landing Gear repair kit for the follow jack that will fit, part # LG-146060. For a lead jack repair kit use # LG-146059. Since repair parts will eventually be unavailable for this landing gear I suggest you consider replacing the setup with a new one such as # RVLG-8HDL which is rated for 8K. A motor kit can be added using part # M1230.
  view full answer...


• Width of etrailer Landing Gear Tubes
  
• The Landing Gear Set w/ Handle # RVLG-8HDL has an outer tube width of 2-1/2" and an inner tube width of 2-1/4". It has a capacity of 8,000 lbs and can be outfitted with a motor # M1230.
  view full answer...


• Can Trailer Landing Gear Legs be Welded Directly to Frame
  
• Trailer landing gear sets like the etrailer.com # RVLG-8HDL that you referenced are designed to bolt onto brackets that are welded to the frame. In terms of function or capacity there is no particular reason you couldn't just weld the legs directly to the frame instead but I don't recommend doing this for a couple of reasons. First the actual install process is going to be a lot more in depth than just bolting to existing brackets or even welding on new ones for the legs. You will need...
  view full answer...


• Compatibility of Replacement Crank Handle
  
• The Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL is designed to be a replacement handle for Landing Gear Set # RVLG-8HDL. Replacement handles attach to landing gear in a number of ways so they need to be matched with their manufacturer. For example, # LC119226 is a replacement manual crank for Lippert Components landing gear. Once you take a look at the manufacturer of your landing gear, just go to the link I've attached which has each of our available...
  view full answer...


• Replacement Landing Gear for 2007 Weekend Warrior LE3305
  
• To find the correct landing gear for your 2007 Weekend Warrior LE3305 you'll only need to know the distance between the weld stops that your current landing gear is attached to. From there you can choose the lift and weight capacity of your landing gear and if you want a manual or electric motor. Standard measurements for weld stops are 15-1/2 inches from inside to inside and 17-1/2 inches from outside to outside. Those dimensions are the same used on top sellers such as Bulldog Electric...
  view full answer...


• Difference Between Landing Gear Sets
  
• The only difference between the two landing gear sets you referenced is that Landing Gear # RVLG-8HDL comes with a handle and # RVLG-8000 does not. Apart from that they are the exact same landing gear sets, with 20-1/2" of travel, an 8,000 lb weight capacity, 44-1/2" between the legs when they are as close as possible and 72" when as far apart as possible. This landing gear is designed to fit the standard weld stop measurements of 15-1/2" inside to inside of weld stops and 17-1/2"...
  view full answer...


• Replacement Landing Gear for a 2005 Montana 5th Wheel Trailer
  
• Since one of the jack legs was so badly damaged there could be other, unseen damage to other parts of the landing gear so I do recommend replacing the system. For an inexpensive manual system rated for 8,000 pounds I recommend # RVLG-8HDL. To add a motor you would just need # M1230. This is a great, cost-effective way to add a whole new system to your trailer at about the same price as repairing or replacing parts of other systems.
  view full answer...


• Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
  
• Good news! I was able to go out to the warehouse and measure the etrailer landing gear # RVLG-8HDL for you. I found that the distance between the weld stops from the outside to outside is 17-1/2 inches and from the inside to the inside of the weld stops is 15-1/2 inches. I have linked a dimensional diagram to this page for you to better see where I measured. I have linked this product to this page for your convenience.
  view full answer...


• Outside Leg Dimensions of etrailer.com Landing Gear for 1995 Skyline Layton Fifth Wheel
  
• The Landing Gear Set w/ Handle - 20-1/2" Travel - 8,000 lbs # RVLG-8HDL has an outer tube width of 2-1/2 inches. As long as the weld stop locations shown in the attached photo work, you will have no issues making this a direct replacement and reusing your current brackets.
  view full answer...


• Powered Jack Recommendation to Replace 3,500 Power Jack that Strains
  
• For your style of A-frame trailer and it's loaded weight the best option is a higher capacity powered a-frame jack like the Husky Brute Jack part # HT87247 which has a 4,500 lb lifting capacity which would be more than needed since your trailer that weighs right at 10k would have a tongue weight around 1,000 lbs. My favorite powered jack to recommend is the Husky Jack part # HT87247 as it has bearings in the screw which allow it to operate quicker and smoother. It also shuts off automatically...
  view full answer...


• Landing Gear Jacks for a Keystone Cougar 5th Wheel Trailer
  
• Bulldog square weld-on jack # BD182513 could potentially be used on a 5th wheel trailer but it really is meant for trailers with exposed frames and doesn't have stops on the outer tube for brackets like landing gear jacks have. If you have brackets already then you would just need to weld on some stops to the outer tube and the heights needed. For a tandem, manual landing gear set you could use # RVLG-8HDL which is both legs with the stops already on them, brackets, handle, and connecting...
  view full answer...


• Landing Gear Set to Replace Lippert Landing Gear on a 2008 Keystone Cougar 5th Wheel Trailer
  
• Yes. You can use Stromberg Carlson Manual Landing Gear Set - 34-7/8" Lift - 8,000 lbs Item # LG-183708 in place of the Lippert set that you have now. Or you can use Lippert set # LC333964 for an electric set or # LC333966 for a manual set. Or you could save some money and go with # RVLG-8HDL. It will use the same brackets that your Lippert system has. Given the options available I would go with this set if it were me.
  view full answer...


• Difference Between etrailer.com 5th Wheel Trailer Landing Gear Kits RVLG-8000 and RVLG-8HDL
  
• The only difference between the two part numbers is that the # RVLG-8000 does not include the manual crank handle and the part # RVLG-8HDL does include it. Aside from that it's the exact same landing gear set.
  view full answer...

Do you have a question about this Camper Jack?