Curt 2" Trailer Hitch - Bumper Mount - 10-1/2" Bolt Pattern - 5,000 lbs GTW

See what our Experts say about this CURT Bumper Hitch

• Bolt Hole Spacing and Top Plate Dimensions of Curt Bumper-Mount Trailer Hitch C19031
  The smaller round holes on Curt trailer hitch # C19031 are approximately 7 inches apart on center. The top, flat part is 4 inches by approximately 12 inches though it is hard to measure exactly because of the rounded sides. I have included a picture.
  view full answer...
  
• Recommended Trailer Hitch for a 2021 EZGO TXT Golf Cart
  I did some research and it looks like the 2021 EZGO TXT is a golf cart. With that being said the easiest option would be to use the Curt 2" Trailer Hitch # C19031. This hitch in theory would get bolted to a flat metal frame piece on the back of your golf cart and provide a 2" receiver however you are going to be limited to the capacity of the golf cart.
  view full answer...
• Hitch for 2015 Ford Explorer XLT to Allow Use of Hitch-Mount Cargo Carrier
  When using a vehicle hitch for a static load like a hitch-mount cargo carrier the hitch rating that matters most is its tongue weight (TW) rating, which is downward force on the hitch tube from whatever item is installed in it. I do not recommend use of a bumper-mount hitch for a cargo box application. Instead I suggest using a frame-mounted custom-fit hitch with a high TW rating, Draw-Tite 2-inch Class III hitch # 76034. Since this hitch bolts to the vehicle's frame it can offer a much...
  view full answer...
• Hitch Recommendation for a 2014 Chevy Silverado 1500
  The Curt Hitch part # C19031 that you referenced is a universal fit hitch that is designed to fit several vehicles. The distance between the mounting holes is 10-1/2 inches. Most likely there would be drilling for installation. A better solution for you would be a custom fit hitch designed to fit the frame of your truck. This will provide you with a hitch that will fit without modification and will have a much higher capacity. The most popular option we carry is the Curt Hitch part #...
  view full answer...
• Trailer Hitch Recommendation for 2001 Chevy S-10 with Factory Step Bumper
  For your 2001 Chevy S-10 with the factory step bumper what you would need is the Curt hitch part # C13021 which is a confirmed fit for your truck and it's configuration. The # C19031 that you referenced is a universal install hitch that isn't designed for your truck specifically so it's not going to fit it easily if at all.
  view full answer...
  
• Universal Bumper Mount Hitch or Custom Fit Hitch Receiver for a 2013 Nissan Frontier
  The Curt 2" Trailer Hitch - Bumper Mount - 10-1/2" Bolt Pattern item # C19031 is a universal fit for any truck with a step bumper. I have linked a diagram detailing the measurements of this bumper mounted hitch. This is not a custom fit so you will have to drill into your Nissan Frontier's bumper. If you would like a custom fit hitch that bolts directly to your vehicles frame I recommend the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" item # e98869....
  view full answer...
  
• Trailer Hitch Receiver For a 1989 Ford F-350 Pickup Truck
  With the Curt 2" Trailer Hitch # C19031 only rated for up to 5,000lbs that is the most it is capable of towing. The maximum tongue weight is 500lbs. This receiver is a universal type fit that mounts on bumpers with 10-1/2" between center on the bolt holes. I do believe on your 1989 Ford F-350 the bumper is not rated for the same amount that you can haul with a Trailer Hitch Receiver that attaches to the frame. I recommend using the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25122 on...
  view full answer...
• Trailer Hitch Receiver Recommendation For 2017 Chevy Equinox
  While there is a trailer hitch fit for your 2017 Chevy Equinox, the part you mentioned won't work because it is a fit for pickup trucks with step bumpers, which your Equinox does not have. So instead, I recommend a hitch from etrailer: - etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" # e98865 I really like this hitch for your Equinox because it is concealed but for the receiver, which will help ensure your Equinox keeps its clean look. This 2 inch hitch...
  view full answer...
• Recommended Trailer Hitch Compatible with 1989 Jeep Comanche
  The Curt 2" Trailer Hitch # E-3S has holes that are 7-3/4 inches apart if you view the video at the 1:20 mark. It is a confirmed fit for your 1989 Jeep Comanche as is the # C19031 which has a 10-1/2 inch on center bolt pattern. Based on your measurements, I recommend using the # E-3S hitch your mentioned with uses 3/4 inch bolt on the wider part and 1/2 inch bolts on the narrower mounting holes. It is made to fit your bumper, but you still may need to enlarge the holes using a rotary...
  view full answer...
  
• Bumper Mounted Hitch Available that Might Fit a 1990 Chevy C1500
  We have the universal bumper mounted trailer hitch from Curt which is part # E-3S. It's not a confirmed fit for your 1990 Chevy C1500 but I attached a picture that shows it's mounting hole dimensions.
  view full answer...
  
• What is the Front to Back Width of the Mounting Plate for Curt Bumper Mount Trailer Hitch 19031
  I spoke with my contact at Curt and the mounting plate measures 4 inches front to back. Please note that the 10-1/2 inches is the center to center distance between the mounting holes for hitch # C19031. I have included a link to the installation instructions for you. We also have # E-3S. Its mounting surface is 11 inches by 4 inches and the small mounting holes on top are 6 inches apart on center. The larger holes are 8-3/4 inches apart on center. I have linked a video review of this hitch...
  view full answer...
• Can a Trailer Hitch be Installed on a Golf Cart to Pull a Single Axle Trailer
  An RV frame trailer hitch such as # 13703 is going to be too large to install on a golf cart but I have some options that could work for you. First, take a look at the Reese Towpower 3-Way ATV Hitch # RP7065100. If your golf cart has a 5/8 inch tongue or frame hole at the back center you could bolt on this 2,000 pound capacity hitch (limited to the capacity of the golf cart). Another possible option is a hitch such as # C19031. There would need to be a flat metal frame piece of the golf...
  view full answer...
• Trailer Hitches for 2004 Mazda B Series 2300 Pickup
  For your 2004 Mazda B Series pickup we offer both 2-inch Class III and 1-1/4-inch Class II rear hitches that you can see on the linked page. From among all options I suggest the Draw-Tite # 75082. All of these are frame-mounted hitches, unlike the bumper-mount Curt # E-3S and the similar # C19031 which are universal-fit items meant for installation on the bottom of a step bumper. Both of these bumper-mount hitches share a 5000-lb capacity; they differ in their mounting hole spacing. I...
  view full answer...
  
• Recommended Trailer Hitch for 2018 Toyota Tacoma
  For your 2018 Toyota Tacoma that has the factory step bumper, I recommend the Curt Hitch # C13264. This Class III hitch is confirmed to fit your truck and will use existing holes in its frame for a no-drill installation. It features a 6,000 pound towing capacity and will provide you with a 2 inch receiver opening. I have attached an installation video on the 2017 model Tacoma that you can use for reference. All of the necessary hardware is included. If you were instead looking for an...
  view full answer...
• Trailer Hitch Recommendation for 2017 Chevy Colorado for Carrying Bike Rack
  Since the Curt universal hitch part # C19031 is designed as a multi-fit hitch it does not have capacities or guarantees that it will work well on a vehicle without damaging anything. I have a solution that I can guarantee will work well on your 2017 Chevy Colorado though. The frame mount Draw Tite hitch part # 76004 is a confirmed fit for your truck and would easily carry a bike rack. I attached an install video for more info. The most popular bike rack we carry that has been confirmed...
  view full answer...
• Recommended Trailer Hitch For Carrying Two Bikes With 2008 Lincoln Town Car
  I have a different option for you, but the Curt Bumper Mount Hitch # C19031 only fits trucks with a step bumper and as such will not fit your 2008 Lincoln Town Car. Instead you will need to go with the Curt # 13707 which is designed for your vehicle and will be perfect for carrying two bikes with a bike rack thanks to the 400lb tongue weight rating of this hitch. If you do not already have a bike rack I recommend going with the Yakima RidgeBack 2 Bike Rack # Y02457 which will fit this...
  view full answer...
• Trailer Hitch Recommendation for a 2002 GMC Sierra 1500 with Factory Step Bumper
  To determine if the Curt bumper mount trailer hitch # C19031 will fit your 2002 GMC Sierra 1500 with factory bumper you have to look to see what the holes spacing is on the bumper. The hitch will fit if the bolt holes are 10-1/2 inches apart on center. If the hole spacing won't work with your truck I recommend a frame mounted hitch, # 13322, which will also be a stronger hitch since it attaches to the truck frame. It is rated for 600 pounds tongue weight and 6,000 pounds gross trailer...
  view full answer...
• Trailer Hitch Fit Recommendation for 2007 BMW 530xi Wagon
  For your 2007 BMW 530xi Wagon we have the Curt Class I hitch part # C11498 which is a confirmed fit and will work well. The # C19031 would not fit so you would not be able to use it. For a ball mount you'd then want the part # C45510, for a hitch ball # C40018 for a 2 inch ball or part # C40001 for a 1-7/8 inch. For trailer wiring you'd need the universal install kit part # C59236 which has been tested as fitting your vehicle.
  view full answer...
• Recommended Trailer hitch Receiver For a 2008 Ford Ranger 4x4
  I recommend installing our etrailer Trailer Hitch Receiver # e29AR on your 2008 Ford Ranger 4x4 with the 4.0L 6 cylinder engine. The frame mounted receiver may require the drilling of 2 additional holes as Ford did not drill these holes in every Ford ranger. There is also not a bolt on receiver for your bumper. I have linked the installation instructions below so you can see where the holes are ahead of time to determine if you will need to drill. If you will need a 4-way flat connector...
  view full answer...

Do you have a question about this Bumper Hitch?