Call etrailer.com at 800-298-8924 for expert service. We are your Pontiac brake controller experts, and offer a lowest price guarantee. etrailer.com carries a complete line of Tekonsha products for your Pontiac Torrent 2007. Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional part TK90160 from Tekonsha can be ordered online at etrailer.com. Complete brake controller installation instructions and technical support.
$94.95
Select Your Vehicle

View Cart



Brake Controller > 2007 > Pontiac > Torrent

2007 Pontiac Torrent Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional

Tekonsha Brake Controller

(406 reviews)


Code:   TK90160

Retail:$107.91

Price:$94.95


Shipping Special

Shipping Weight: 1.25 pounds

Quantity: 






2007 Pontiac Torrent - Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional

Proportional brake controller automatically levels when mounted within a 90-degree vertical range. Includes digital display, 3 boost levels, battery protection and continuous diagnostics. Easily transfer between different automobiles.


Features:

  • Brake controller activates trailer brakes in proportion to your Pontiac Torrent's braking action
    • Automatically adjusts trailer's braking based on deceleration of tow vehicle
    • Activates immediately - no pausing like with time-delayed brake controllers
  • Automatic-leveling ability - internal sensor detects deceleration even if controller is not mounted flat
    • Position anywhere from 0 degrees (level) to 90 degrees in the vertical plane
  • 3 Boost levels let you adjust initial braking power and aggressiveness
  • Continuous diagnostic check alerts you to any potential problems
  • Integrated safeguards protect your vehicle and trailer
    • Minimizes drain on car battery when not in use
    • Prevents trailer brakes from overheating by reducing power output to them during prolonged stops
  • Easy-to-read LED display
  • Built-in, slide-bar manual override
  • Quick-disconnect feature lets you easily remove and store the control when not in use
    • Replacement wiring harness (sold separately) and replacement bracket (6927 - sold separately) required to move the controller from one vehicle to another
  • Plug-in, vehicle-specific brake-control adapter (sold separately) can be used for certain applications to reduce installation time


Specs:

  • Application: trailers with up to 3 axles (6 brake assemblies)
    • Designed for use with electric brakes only
  • Dimensions: 4-3/8" wide x 5" long x 2-1/2" tall
  • Mounting: between 0 degrees (level) and 90 degrees in the vertical plane
  • Limited lifetime warranty


Proportional Braking

With a proportional brake controller, you can get heavy-duty emergency braking, general braking or slow-to-an-idle braking for your trailer automatically. The intensity with which your trailer brakes are activated and the rate at which they are applied are dependent on the deceleration of your tow vehicle. This means that, unlike time-delay controllers - which send the same amount of preset power to your trailer brakes every time - proportional controllers are able to adapt to every braking situation differently. So, if you slam on the brakes in your truck, your trailer brakes will activate with that same extreme intensity. And if you merely slow down as you approach a red light, your trailer will gradually brake in the same manner. Just set the initial power level, select a boost setting, and you're good to go.


As long as the Primus IQ controller is properly mounted and is pointed in the direction of travel, it will sense - via an internal inertia sensor - how your tow vehicle brakes. This inertia-based sensor responds to the deceleration of your tow vehicle as you brake by signaling the controller to send out enough power to your trailer brakes so that they are activated with an intensity that matches. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.


Power Boost for Heavy-Duty Towing

Aside from smoother, more efficient braking, Tekonsha's Primus IQ brake controller also offers a boost feature that gives you more initial braking power for those times when you're towing heavy loads. You can switch boost levels so that the power output to your trailer brakes automatically starts out at either 13 percent or 25 percent of the predetermined power setting.


So, if you boost the initial power so that your trailer brakes activate with 25 percent of the overall intensity at the start, the brakes will reach maximum braking faster. This is particularly beneficial if you are towing a heavy load because the intensity required to stop that load may be far greater than that needed to halt your Pontiac Torrent. Therefore, sending out more initial power to the trailer brakes - and causing them to reach maximum braking faster - allows you to better control the trailer so that it doesn't push your tow vehicle before coming to a complete stop.


If your trailer weighs less than your tow vehicle, no boost is needed. But if you wish to set the boost so that your trailer leads the braking of your towing setup, you can select level B1. The following table gives an indication of when you might use the different boost levels and the power increases that they offer.


Approximate Gross Trailer WeightBoost LevelIncrease in Initial Power Output
Less than tow vehicle GVWB113%
Equal to tow vehicle GVWB1 or B213% or 25%
Up to 25% more than tow vehicle GVWB2 or B3*25%
Up to 40% more than tow vehicle GVWB3*25%

*Both B2 and B3 offer a 25-percent boost in initial power. But the braking curve for B3 is more aggressive than that of B2. This means that, even though you will start out with the same intensity when using these boost levels, you will get an overall more aggressive braking experience with the higher level. So if you use B3, you will reach maximum braking sooner than if you use B2.


Safety Features

The Primus IQ offers advanced safety features to prevent damage to various components of your towing setup. For example, when it is not in use, this brake controller will be in power-saving mode. In this setting, the power draw falls to minimize drain on your Pontiac Torrent's battery.


When you stop at red lights, or any time that your truck and trailer are at a standstill with the brakes applied for more than 5 seconds, the Primus IQ's "hold" feature will activate. When this happens, the power output to your trailer's brakes will be reduced to just 25 percent of the preset power setting so that the brakes will not overheat.


If ever there is a time that you need to brake your trailer separately from your tow vehicle - when traveling down a steep incline, for example - the manual override is easily accessible. Pushing this slide bar engages the brakes on your trailer with full power. In addition, when you activate this override, the brake lights on your trailer will illuminate, properly warning those behind you of the braking action of your rig.


In addition to all of those safety features listed above, the Primus IQ offers diagnostics such as:

  • Open ground
  • Overload
  • Output short
  • Faulty mounting
  • Power loss
  • No trailer connection

Automatic Leveling and Simple Installation

The self-leveling feature of the Primus IQ ensures that the brake controller continues to function even as you drive up steep hills or through the mountains. Simply mount it in your cab at a vertical angle that is between 0 degrees (level) and 90 degrees, and the controller will level itself automatically.


Correct Primus mounting90-Degree Primus mounting

Note: The Primus IQ must be mounted on a level horizontal (side-to-side) plane and must be lined up with the direction of travel for the internal sensor to function properly.


Installation is a snap. After mounting the Primus IQ unit in your cab using the included bracket, hardwire one end of the included pigtail harness directly into your Pontiac Torrent. The other end plugs into the brake controller. To transfer the Primus IQ to another vehicle or to remove it for storage, just unplug the unit and snap it out of the bracket.


Installation Accessories

For even easier installation, a vehicle-specific wiring adapter (sold separately) is available for most newer trucks and SUVs. One end of the custom adapter plugs into your Pontiac Torrent, and the other end plugs into the controller - no hardwiring required.


Note: If a custom brake-control wiring adapter is not available for your Pontiac Torrent, one of the following will be required:

20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications

30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications


See also etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your Pontiac Torrent.



90160 Tekonsha Primus I-Q Proportional Trailer Brake Control

39528 Hidden Hitch Proportional Brake Control

20191 Draw-Tite I-Stop IQ Proportional Brake Control



TK90160 Installation InstructionsInstallation Details TK90160 Installation instructions


Related Products



Pontiac Torrent, 2007 Owners Who Purchased this Brake Controller Also Bought...








Customer Reviews

Tekonsha Primus IQ Trailer Brake Controller - 1 to 3 Axles - Proportional - TK90160

Average Customer Rating:  4.9 out of 5 stars   (406 Customer Reviews)


Proportional brake controller automatically levels when mounted within a 90-degree vertical range. Includes digital display, 3 boost levels, battery protection and continuous diagnostics. Easily transfer between different automobiles.


- TK90160

by: Jim H.06/11/2014


Shipping was great. Stared at it for a couple of days before unpacking. The trailer connector mounting was easy with the holes almost matching the existing holes on my 2013 Toyota Highlander. The first four wires are a snap, they are just plugged into the existing four pin connector. I routed the two wire cable towards the front using ty wraps and improvised L brackets fixed to existing chassis screws. I mounted the Circuit Breakers on the inside of the left fender making sure there was hood clearance (see photo). Then I hit a snag. There was no easy way to get the brake and 12V power wire to the brake controller inside the car. For grins, I goggled "brake controller video" for my car and came up with a video made by "eTrailer." (Thank you eTrailer) Three things from the video helped me: wire access from inside the car through the firewall, a place to mount the controller and how to locate the brake wire. After the installation I had 18" of two wire cable left over. The install took me about six hours. (I'm 71 and I took my time.) A couple days later I connected the trailer for a test ride. The brake controller worked like a dream. Things I liked: Retaining the four wire trailer plug setup next to the seven wire trailer plug. Controller display works but you don't have to look at it. The two wire cable was adequate for the job. Being an Engineer (retired) I worry about things like that. Thing I didn't like: The mounting plate for the trailer plug is a little weak. A stiffer plate would have been better suited for me. and, oh yeh, somebody else to install it. ;=) 135250



- TK90160

by: J06/19/2013

2006 Toyota 4Runner


THANKS for the Brake Controller unit from ETrailer. It arrived w/in 5 days from your MO location to my So CAL residence. Even as an Engineer/Scientist from the Delta IV rocket program and no experience with brake controllers, I was able to install this unit by myself. Your continued (live human) support and online video clips proved to be the key elements to this installation...without my symbolic pocket protector. I have attached a few images of the unit, mounted to the fuse-panel cover (3/16 attachments with locking hex nuts) in a 2006 Toyota 4Runner SR5 (with factory tow package). The placement of the unit onto the panel cover allows a new panel cover (no holes drilled) to be used when it is time to sell the vehicle. 85308


Comments

Thanks Patrick for the follow-up. The brake controller, for the camp trailer, installation went relatively easy and operation of the unit continues to be great. More importantly is your product follow-up for Customer Service...providing a r-e-a-l name vs. Customer Service dept. along with a phone number and email contact information all pretty rare in todays environment. E-Trailer continues to be my first-source for product information search.

J - 12/19/2014

8102

- TK90160

by: David06/17/2014

2009 GMC Sierra 2500HD


Installed quickly an easily into my 2009 GMC Sierra 2500HD by wiring up to the factory harness. Be sure to watch the etrailer.com video to see which wires need connected at the fuse box in the engine compartment! (Easy hook-ups, just need to make sure you see which ones get hooked up and where.) And if you don't use your ash tray, these brake controllers squeeze nicely into the ash tray compartment/recess in the lower part of the dash. Makes a great place to keep most of the controller out of the way and it's easy to install (you will have to create 2x new holes in the plastic detachable controller mounting bracket but its very easy - you can see the mounting screws in the 'new' holes and the old holes go unused as shown in the photo). Only had a trailer hooked up once, but the controller functioned as designed. I think the 'Boost' function will come in handy if I use a well-loaded trailer and need some additional stopping power from the trailer. 135875



- TK90160

by: Erick S07/26/2016


IT WORKED PERFECTLY. This is my first time to purchase, install, and use a brake controller. Add to top it off, it was my first time to pull a trailer. It was on a Saturday, exactly six days before a scheduled tent-camping trip, when my wife found a good deal on a used pop up camper. The camper was equipped with electric brakes, so it was required to install a brake controller on my SUV. It was Sunday (next day) when I ordered the Tekonsha TK90160, along with the other necessary part numbers #118449, #A0500, #18136, #ETBC7. I was planning to take the parts to a shop to have it installed as soon as I received them. I was hoping I can get them on Tuesday, but UPS dropped it off to the local post office, which caused it to be delivered at 3pm on Wednesday afternoon. The shops that I went to either did not have an installer available, or were all booked for the week. I had to "take courage" and install it myself. I am so thankful that etrailer.com provides extensive videos of reviews, installation, and operation of the products that they sell. I made the connections as shown and hoped for the best. I picked up the camper on Thursday, and was sooo relieved that it worked perfectly. We took off on Friday and the camping trip was a success. We are looking forward to making more good memories with our camper. Thank you etrailer! 276385



- TK90160

by: A happy, new farmer09/04/2013

1997 Chevy K1500


I installed this on my 1997 Chevy K1500 pickup to pull my farm trailer, Kubota tractor, and it's implements (total of about 5500#s). I bought my truck new in 1997 with the towing package. eTrailer had a number of links related to the installation, but the most helpful was the one that identified the blue brake and orange power wires that, in my case, were preinstalled at the factory. That made the job significantly easier. What I thought would be the most challenging part of the install turned out to be simple, but only because of pure, dumb luck. Because I had installed aftermarket security and stereo systems shortly after I bought the truck, there was no way to identify/compare the pictures/discussions to identify the hot brake wire under the dash near the brake (other than that it was likely a white or gray wire). The circuit tester (purchased with my order from eTrailer) turned out to be a godsend. Unbelievably, the first white wire I tested turned out to be the hot brake wire! I was very lucky to hit the correct wire on the first try. The first time I hooked up to my trailer, the system worked flawlessly... exactly as the instructions described. And the performance is excellent. Note: I double/triple checked connections as I worked. I highly recommend doing this. Hunting down electrical connection malfunctions is not something you want to do. Overall, I'm VERY happy with my purchase and the support from eTrailer. I highly recommend this product and eTrailer. 98210



- TK90160

by: V Johnson10/02/2015

1990 Chevy Blazer


I have installed the Tekonsha Primus IQ Brake Controller with the ETBC7 Brake Controller wiring kit on my 1990 Chevy Blazer Scottsdale. Everything that I needed was included and the installation instructions were simple. We will be trying it out for the first time in early November when we are going to rent a small travel trailer. If we like the experience we may buy a travel trailer to go with our brake controller! Before and after pictures attached. Thanks for the quick service and support. 228964



- TK90160

by: Linus01/30/2014


Pictures of the install. Approximately a 20 min job. First picture my finger is pointing to the factory plug with the etrailer supplied harness plugged in. Note the harness did not specify that the white common with the ring terminal should be connected to ground. But then again that SHOULD be obvious. I will be towing this weekend so I will rate the product then. One minor gripe is that there is always power to the unit which is a battery drain (as evidenced with the key out of the ignition and the unit stayed on) Not sure as to the impact but the controller can always be unplugged or removed. Sorry for the dirty floor mats in the photos. 115201


Comments

Just a quick note, there is an automatic shut-off on the Primus IQ. After 15 minutes or so of in activity, the controller will power down automatically. As soon as the controller detects movement, it comes back on. No battery drain, and you do not have to remember to turn the controller off or on.

Patrick B - 01/30/2014

2673
Comments

what year Tundra in pics . I have a 08 and I am going to get an IQ for it . do you still like yours ? i guess a ground is needed ? I see what looks like a one white wire with harness

comment by: Les H - 08/09/2015


14081



- TK90160

by: Howard H09/04/2014

2004 Toyota Tundra


Just wanted to follow up with you. I have an old 2004 tundra. I got rid of a 3 year old 3500 Chevy and got in that 04 tundra. I have had a goose neck hitch and pull a 24 ft. With a dove tail, 3 beam trailer with that tundra. I have always had e-brakes, but had a used controller which I had wires spliced into place for the controller. I pulled that trailer for 10 years with that tundra and never really felt comfortable with the e-braking system. I kept that tundra kicked in the ass for 10 years with the loads I pull and was always on caution due to my lack of confidence in the braking system of that setup. We'll, I bought your controller and factory ready quick connect wiring harnesses for my make and truck model. We'll let me tell you that I have never felt so confident pulling a trailer in my life as I do now with the flexibility and control I have on my E-braking system now. I'm still up in arms on deciding wether this is better advertisement for you and the breaking system with the quick connect wiring harness, or better advertisement for the 10 year old tundra that I have always had and continue to kick in the ass with loads that onlookers shake their heads at when they view the work that my 10 year old truck and e-breaking system handles. This new e-breaking system allows me to have the confidence that I can control the velocity of the load I'm hauling with ease. Thank you. 150117



- TK90160

by: Bruce Goosman08/18/2015

1998 Ford F-150


Have not had a chance to use this yet as we are picking up our trailer over Labor Day Weekend. HOWEVER!! Installation was a SNAP! It took me longer to find the screws I kept dropping than it did to install the cable and control!! SUPER EASY!! Installed it inside the useless hole in the lower dash to the bottom right of the steering wheel on my 1998 F150. Drilled a on inch hole in the back of the compartment and ran the wire through. Secured the metal bracket with the supplied screws and attached the control. I wish everything installed this easy!! Looks great, VERY easy to understand instructions and all the parts are there! 220152


Comments

Its now at home in a 2004 F150 and works fantastic! No adapters or relays needed. Plug and play! Controls the brakes perfectly on our 24 camper!

bruce g - 08/17/2016

20321



- TK90160

by: L. Miller06/17/2015

Nissan Frontier


The controller is super easy to install. I have the plastic bracket mounted low at the bottom dash board of my Nissan Frontier to get the proper angle for operation. When needed I just plug in the end from the wire harness and pop the controller into the bracket with a click. The instructions for operating and adjusting the controller are straight forward. Read them a couple of times or have them with you before you start towing for real. The "boost" feature is a great way to fine tune the controller and you can adjust it "on the fly". A great product all around. 204020


Comments

My controller still works great though Ive not used it lately. I still highly recommend this brand and model.

L. M - 06/16/2016

18645



- TK90160

by: Chris Curtis05/30/2015

2006 Ford E-150


I bought the above brake controller, the ETBC7 brake controller wiring kit, and the Tekonsha plug in wiring adapter for my non trailer equipped 2006 Ford e150 passenger van. I already had the 4 wire plug installed in the van, but not done very well. I started redoing the 4 wire circuit to hide the wiring better, and then mounted the back plug and cleaned up all the wiring in about 45 minutes. I took another 1/2 hour to pull the wire forward to the battery area, and lock it down. It then took about 45 minutes to mount the brake controller inside. Buying the adapter cable saved me a good 1/2 hour or better. The entire thing done in about 2 hours and likely better than a shop could have done. My advice is watch the videos, they had one for a van very close to mine and it made the installation steps very clear to conceptualize. P.S. I'm an Amazon prime member. The brake controller was the exact same price as on Amazon. Amazon however did not have a well equipped wiring kit, nor did they have the harness adapter. I definitely would not have saved money buying on Amazon and I would have lost time due to not having the harness adapter. 198858



- TK90160

by: Tater05/13/2014


The Tekonsha Primus IQ controller is a well made compact unit that is perfect for my FJ. The ETBT7 wiring kit has all you need to go from 4 to 7 pin connectors. I was worried about how to remount the 4 pin, but the new 7 pin has a 4 built in it. It is a very clean install. The kit had everything needed to install, including a test light. The Tekonshcontroller and the wiring kit are high quality and have complete easy instructions, and had everything needed for the install. Etrailer didn't have the ETBT7 in stock when I ordered and I paid for expedited shipping. They followed up with emails and calls to inform me what was happening, and offered to refund the shipping fee. I told them just expedite it when it came in and they did, got to me in two days. I recommend trailer highly, they kept me informed, were prompt, friendly, and concerned, and paid attention to detail. If only other companies followed their example... Excellent prices, Great product line, great company, great staff. I will use them for all my trailer needs. I Recommend them highly. 130304



- TK90160

by: Mike R04/02/2013


I had one of these before and it worked well. Etrailer had a great price on it and when I needed to put one on a different vehicle I bought from them. I couldn't be happier. 73894


Comments

I sold the vehicle but kept the controller and my new truck has the factory brake set up. I need to get the wiring harness for it as I left it in the vehicle. Ill get around to it one of these days and probably end up selling the controller. Its a good unit and worked like a champ. Which reminds me, I was going to buy some LEDs for the trailer. On the list for this winter I guess.

Mike R - 10/02/2014

7103

- TK90160

by: Stanley L.05/01/2013

Toyota 4Runner


I purchased the Tekonsha Primus IQ Trailer Brake Controller and the wiring kit for my Toyota 4Runner. It was simple installation and the customer service was EXCELLENT! They sent me extra schematics I needed by email and was very supportive! I will definately do business with them in the future. 78575


Comments

Tekonsha Primus IQ Trailer Brake Controller has worked great! Very satisfied with it and purchasing it from this company.

Stanley L - 05/05/2014

3966

- TK90160

by: Pam G.06/12/2013


I chose this device based on my trailer repairman's brand recommendation. He usually has them in stock but was out. I got mine before his order came in. He also did not have a wiring harness for my vehicle so I ordered that, too. This is the first time I've ordered anything significant that I knew virtually nothing about. From the descriptions and pictures on the etrailer site it was easy to look up what I needed. I also read on the site about time control vs proportional and then knew the proportional would be good for me. I have a new camping trailer that has electric brakes; need the controller to operate the trailer brakes. The product quality of the brake controller appears very good. The wiring kit is quite substantial. My mechanic will wire up for me this week end and I'll have his opinion then. I am very satisfied with the speed of the delivery and the quality of the products. thank you 84360



- TK90160

by: Greg D08/09/2013


Super easy installation. Clear, thorough instructions. Everything you need to install included. Digital display codes are a little quirky so you'll need to keep the quick start manual handy until you get used to them. 94094


Comments

We still like the brake controller. I was able to install it in about 5 minutes working in the rain at twilight. Its easy to set and adjust. Would buy another if needed.

Greg D - 03/03/2015

9822



- TK90160

by: Sam S.10/09/2013

Toyota Sequoia


Like other reviewers the biggest challenge was getting the cover plate removed (and replaced) to access the factory connection. The connection was at the very top of the wiring bundle and I was able to cut about 1/2" of the tape holding the bundle together very near the connection to gain access without removing or cutting all of the tape. The ground terminal was easily accessed and the installation was quick and mostly painless. The instructions to set the braking level was spot on. I have a Sequoia with a knee airbag and tire pressure monitoring. I place the controller with the open back of the bracket allowing access to reset the tire pressure monitoring switch. 103222



- TK90160

by: Bob P.05/23/2015


Installation was easy on my 2003 GMC Envoy that had the factory installed towing package. Setup for the trailer breaking force was also straight forward. Product works as intended. 195071


Comments

After this winters trip from Columbus, Ohio to Ft Meyers, FL and back, on curvy mountain roads, etc., we are very happy with the products performance.

Bob P - 05/26/2016

17972



- TK90160

by: Rick B.08/12/2015


No problems with installation as cable fit existing connection perfectly. Not being that familiar with controllers it took a few times and some use of it to get the hang of it. Would recommend to anyone. 218751


Comments

Made about 6 trips so far and the controller works as expected. Easy to adjust for different situations and monitor.

Rick B - 08/13/2016

20203



- TK90160

by: Andy H.04/05/2015

2013 Ford E-350


Controller and wirering harness arrived in one night. Installed easy and clean in an hour and worked properly ever since. True plug and play with my 2013 E-350 xlt van. The OEM tow package connector is on the back of the coin cup in the dash. Great thing is that the Primus IQ fits perfect in the holder after you open up the back of the coin holder a bit for the connector. 183256



- TK90160

by: Al Rey12/11/2014

1995 Ford F-150


I received this brake controller and the cable designed for connection to my 1995 F150 truck within the time I was told. I hooked them up and I was ready to tow my trailer. It seems to work well, but I will not know until I take the RV trailer out for a run, soon. Thanks for the great service. Also, This was the second brake controller I tried. The first was a Curt brake controller and failed to work properly, so Katie of etrailer helped me pick out another brake controller (this Tekonsha Primus model). Installing the wiring and 7-pin connector was another story. Careful placing your order, if you make an error you will be responsible for return shipping. better to call in your order and verify that the parts you are ordering are correct for your vehicle. 164341



- TK90160

by: craigjjr09/28/2015


Outstanding, from start to finish. This was a super simple and easy installation process. I started by watching the e trailer video to see what the installation would be like in my vehicle. They give detailed instruction which allowed me to inspect my vehicle before purchase to see if this will fit "as advertised". I bought the brake controller and special pigtail for my truck and all I needed was to drill 2 holes in the bumper for the receptacle (trailer plug), plug in the trailer connector, install bracket under dash and plug in the pigtail and the project was complete. Very easy. Instructions for the setup to trailer are simple and clear and very easy to complete. I am completely satisfied and highly recommend this product and e trailer to everyone. 228080



- TK90160

by: Alan B01/08/2014

Dodge Ram


Purchased the Tekonsa Primus IQ controller with wiring adapter for my Dodge Ram. Shipment arrived quickly and was exactly what I needed. Installation was a piece of cake. Cut an opening in the plastic stock dash location. Plugged the adapter into the Dodge plug under the dash and into the Primus. Worked perfectly. No fuss. Installed in about 10 minutes which included the time to cut the opening.. Picture will be poster... I was so happy with the service from etrailers that I ordered the Blue Ox Swaypro hitch. Thanks ETrailer.com! 112238



- TK90160

by: Anton07/30/2015


Finally got to try this unit and it works awesome with my 21 foot camper. It only took 30 minutes to install and plug in, in my '06 avalanch. 215577


Comments

Still a happy camper. Works the way I want it. Nice and smooth! Highly recommended.

Anton - 07/30/2016

19806



- TK90160

by: Matt L.09/22/2014

2014 Nissan Frontier


Quick, plug and play installation on my 2014 Nissan Frontier. This is the second Tekonsha brake controller I have owned- the quality continues. 152374


Comments

All working well. 100 of miles of towing and no problems. Thanks for checking in

Matt L - 09/28/2015

15296



- TK90160

by: Ray B of Colo.11/18/2013


I purchased a Primus IQ from our local NAPA dealer and had already installed it in one of our Dodge trucks before I learned about Etrailer. Needless to say it cost a bit more than the one I ordered from Etrailer a couple weeks later. you cant return electrical products once installed. I received the one from Etrailer in a very timely manner. I was hoping it wasn't a #2 for it being so much cheaper, but it is just fine and installation was no problem because I already had Tenkonsha Voygers so just chop the wire and install new control unit. We have two trucks and pull various trailers, so am real happy with product and will further order trailer items from ETRAILER.COM. Thank you, just Ray 107693



- TK90160

by: Tim07/31/2015


This brake controler works very well.installation was very easy in my 2015 ram 3500.10 min and I was setup and ready to roll 215890


Comments

still working great.no problems at preforms well pulling my 36ft camper

timothy b - 07/30/2016

19810



- TK90160

by: Paul06/29/2014


This is very easy to install and adjust and the service at e-trailer is great Christy was a great help and shipping was fast 138221


Comments

It is still working fine would purchase another one

Paul - 07/05/2015

13052



- TK90160

by: George K.06/06/2016


I installed the unit in a 2016 Toyota Highlander LXE. That year has no plug and play wires making a complete wire job a pain. The 7 pt. connector installed perfectly and the supplied wires were sufficient. I had heard getting through the fire wall to the engine/battery area could be done by removing a portion of the plastic liner in the drivers side wheel well to follow the hood release cable. That proved much to difficult so I got through via a computer wires grommet. (upper left). The controller is small and compact with an excellent plastic snap in bracket. It installed at the right knee area in a very limited available area. I expect good test results. 258141



- TK90160

by: Erik N.05/19/2013

2012 Jeep Rubicon


I bought this product after reading several reviews. I recently purchased a Fun Finder 189FBS Travel trailer, and I needed a Brake Controller that was proportionally controlled. After my first trip with my 2012 Rubicon/ Fun Finder; I am very pleased with my purchase. This controller works best for my setup, on the "b1" boost level. Setup and installation took less than 2 hours, and I did it myself. The instructions and reference video from etrailer.com were very helpful. I was quoted nearly $400 to install this controller from my local RV shop. I bought it hear, spent 2 hours, and saved $250. If you can crimp a wire, and run a drill- You can do this! 80929



- TK90160

by: Anthony Seals02/18/2015

2007 Ford F-150


The Tekonsha Primus along with the Tekonsha 3035-P Ford adapter are awesome producs, tested it right after installation outstanding results. Installed on a '07 F150 XLT w/ tow pkg., adapter plugs in behind the OBD2 port, PLUG 'N PLAY (with adapter). 175218



- TK90160

by: Brent B04/07/2014


This product plugged right in and worked perfectly as it should. I like the different boost levels as a quick adjustment between loaded and unloaded trailers. No messing with the gain controller to keep the tires from sliding. The special dodge plug made install a breeze and less than 5 minutes. Much better than splicing into wires. Plus eliminates the need to hunt for the correct wires. This controller works off of inertia so as it senses your truck braking it applies equal braking to the trailer eliminating the jerk experienced from other controllers. Shipping from etrailer was quick as well. Great overall product at a reasonable price. 124031



- TK90160

by: rojoflo04/08/2014


A lot better than the voyager. More helpful and easier to test the system - truck and trailer 124354


Comments

Working great. No problems.

rojoflo - 04/08/2015

10689



- TK90160

by: Steve W.07/21/2014


The electric brake works great. It was easy to install and set up. 142469


Comments

Still working great after a years worth of work!

Steve W - 07/21/2015

13557



- TK90160

by: Steve04/19/2016


I bought this brake controller over a year ago. I installed it in an 03 gmc envoy and was pulling a small hybrid rv that weighted approx 2750 lbs, (single axle). The controller was easy to install and adjust to my vehicle and trailer. Works great. I noticed that it automatically adjusts the amount of voltage output to the trailer brakes if you are on an incline or decline. I now have it in an 05 GMC Yukon pulling a larger rv about 3600 lbs (double axle). The staff at etrailer were very helpful and kind. They had good info for the DIY. I definitely recommend this product and etrailer.com 245963



- TK90160

by: Kevin G.09/11/2012


Product works great, as advertised. The Tech at the RV dealer commented on the reliability of this brake controller, and the install literally took 15 minutes, start to finish. The supplied factory wiring harness made quick, simple work of the installation. The video on the etrailer website is right on the money as well. I have dealt with etrailer for all my towing needs since 1995, and they have never let me down. Great, quality products......quick delivery, and customer service that is second to none. There is no reason to shop anywhere else. Thanks etrailer.......you are the best! 54172



- TK90160

by: Brooks02/14/2014

Toyota Sequoia


I ordered mine with the wiring harness for toyo and Lexus. Everything plugged in nicely and fit perfectly in a Toyota Sequoia under the steering column on the right side. The only suggestions is the that the factory wiring harness in the sequoia has absolutely no slack, so it you order this with an adapter for this make and model, it is a little to short to run it to where I have it. I really had to work to get it mounted. If it had a longer run by about 6 inches it would have been a piece of cake. I still gave it an excellent rating because other than that it was a 5 minute install. 116521



- TK90160

by: Dennis L.07/07/2015


I purchased this trailer brake controller as we had recently bought a camper and the SUV we are pulling it with does not have one. I am going to use it this weekend for the first time. When I called to order it I had no idea about these. The salesperson, Cathy, was extremely helpful and was "over the top" in helping choose the correct one as well a finding installation videos as well as getting the correct accessories for my vehicle. It was a really great buying experience. The installation was very easy and it lit right up after connecting it. Can't wait to try it! 209981



- TK90160

by: Andre Capella03/10/2014

2014 Chevy Silverado


Very easy to install, pigtail 3016 for 2014 Chev Silverado. 120031


Comments

Works good

Andre C - 03/10/2015

9943



- TK90160

by: Mike07/06/2014


Very good product. Great service 139479


Comments

Parts still working great. Thanks

Mike - 07/09/2015

13226



- TK90160

by: Doug M.10/05/2012


While I have not had the chance to use it yet pulling my trailer I picked this particular unit because of the reviews it has received from people that have and are using it. I had it professionally installed and it is working as the instructions say it should. The company that installed it had nothing but good things to say about it as well. I especially want to thank Nicole for her help and customer service she provided to me and I can promise you that all my future trailer needs will be purchased from your company via Nicole. Big Thanks to all of you. 56414



- TK90160

by: Gregory G10/16/2014


Fast and got what I ordered...:) 156275


Comments

Works fine thank u..

Gregory G - 10/19/2015

15604



- TK90160

by: nabrno07/19/2016


Paired this with item ETBC7. I am really glad I did this myself. Saved a lot of money! The installation diagrams that came with the kit were very informative. As for this unit, I am very satisfied. Seems like it comes with some higher end features but at a reasonable price. For my application of towing a tent trailer, I did not need anything super fancy. I do appreciate this unit's proportional braking system so you don't feel the trailer "grab" you every time you hit the brakes. Auto off feature is nice as well. Overall very satisfied. 273508



- TK90160

by: HHH06/15/2013

2003 Toyota Sequoia


Great controler for the price. Easily mounted and set up using the vehicle specific harness. Installed in a 2003 Toyota Sequoia just under the key in the flat of the center cover. Perfect for the 0 - 70 deg mounting location required by this controler. Setup and operation just as was stated in user manuals. eTrailer was great as well, everything came together and on time. 84801


Comments

Im a novice with a 2003 Tundra. Vehicle specific harness options offered while ordering? What level of difficulty would you rate it, what required tools? Thanks

comment by: Corey J - 06/26/2013


1687

A plug-in brake controller harness can be used with your 2003 Tundra, if it came equipped with a factory installed 7-Way trailer connector in the rear. You would use harness 3040-P for most Tekonsha controllers. I have sent you a link to a video that shows an install on a 2007 Tundra. It will give you a clear illustration of the install. All you need is a drill or screw gun, and your standard selection of screwdrivers. If you do not have a factory 7-Way, you will need to use kit ETBC7 to install the system and that is a bit more involved, but we also have videos of that kit so you can see how that is done.

Patrick B - 6/27/2013




- TK90160

by: Patricia04/03/2013

2013 Dodge


I am unable to correctly rate this product at this time because there is no Dodge 2013 harness with which I can attach it. If/when the harness becomes available (a year plus after the truck came out, of course), I will re-review the product. Note that lack of this harness is NOT the fault of eTrailer, but if you're purchasing this for a 2013 Dodge truck, you might want to wait. 73972


Comments

Tekonsha is currently slated to have the harnesses, 3023-P, available by the end of April 2013. There have been running changes to the 2013 Dodge Ram that have made harness availability particularly challenging.

Patrick B - 04/05/2013

1291
Comments

I just purchased mine for my 2013 Ram Crew Cab 4x4, got it with the adapter for the truck installed in 15 minutes and works perfect. April 2013

comment by: Yvan - 04/20/2013


1422

Thank you for the input. I am glad to hear they might be caught up.

Patrick B - 4/25/2013




- TK90160

by: Dale N.08/04/2016


I bought this controller so the trailer I pull my tractor would brake correctly. The initial installation was easier than I expected. I followed the directions and it hooked right up to my 1990 Dodge Turbo Cummins. Since buying it I have been very pleased with the ease of changing loads on the trailer. Different weight different brake response. With push button boost it has made towing almost a pleasure. The simple set up is what I'm impressed with. If you haul differing loads this one's for you. 279594



- TK90160

by: Todd G07/03/2012

2011 Dodge Ram


Plug and play is a true definition. My family was bugging me to go boating this last weekend and being the procrastinator that I am I had not yet installed a brake contoller on my 2011 Ram yet. Got the controller and Harness in the mail on Saturday after only 3 days since order was placed. The install took 10 minutes max including the bracket install and away we went to the River. Thanks etrailer!!!!! Would have never heard the end of it from my 14 year old daughter if we would not have made it boating!!!!! 46597



- TK90160

by: chris c.07/25/2013


I have had a few different trucks in the past, all with brake controllers, some factory some not. So when picking one for my truck, I wanted something with as few a knobs, dials, etc as possible. I looked around on the internet and found the Primus, it was the middle of the road as far as sophistication and basic. It was shipped promptly and arrived within a few days. The installation was easy with great instructions. Would recommend to anyone who wants ease of operation without spending a fortune to get it. 91572



- TK90160

by: Jerry N.10/03/2015


I am replacing a 15 yr old break controller that was flaky. The new technology is quite an improvement. Not having to compensate for the angle of the controller is a real plus. This unit appears to be high quality with a robust connector. The trouble shooting display should be a real help in time of need. The documentation is excellent. I did have one display question that was quickly answered by etrailer. I have a light weight trailer and I expect this controller will perform well. If not, 'I'll be back!' 229056



- TK90160

by: John D12/10/2013

2006 Dodge Ram


The tekonsha controller was easy to install with the help of the instructions, (very well written), and the video, specific to my 2006 Dodge Ram. Set up was also quick as I dialed the power setting to 7, and have just the right amount of braking for my empty trailer. When I loaded trailer for the first time, I adjusted the boost level to the b1 position and that was all that I need to do to have the safety of well adjusted trailer brakes at finger tip control. Very pleased with this pur hase. 109795

73
429
Show More Reviews


Ask the Experts about this Tekonsha Brake Controller
Do you have a question about this Brake Controller?


  • Installation Instructions for the Primus IQ Proportional Braking System 90160
  • There are three possibilities for your vehicle. If you have a factory 7-Way you will be able to use the Tekonsha PRIMUS IQ Electronic Brake Controller, item # TK90160, and the Tekonsha Wire Replacement for Ford, item # 3035-P, to install the brake controller on your RV. The connector for the brake controller wire harness should be located under the dash to the left of the steering column. You will be looking for a 6-pin connector that mates to the brown connector on the # 3035-P harness. The...
    view full answer...

  • Setting Up the Tekonsha Primus Electric Trailer Brake Controller # TK90160
  • The initial set up involves connecting the trailer to the vehicle, starting the engine, and then fully engaging the manual override lever. While the lever is fully engaged, set the power wheel knob to 6. You will then start doing the driving/braking test and then adjust the power wheel accordingly. The power wheel does adjust the amount of power sent to the trailer brakes like you have said. More power (rotating the knob toward the front of the vehicle) will set the brakes more aggressively...
    view full answer...

  • Troubleshooting an SH Code on the Tekonsha PRIMUS IQ Electronic Brake Controller # TK90160
  • If you click on the link that I have provided for the installation instructions, you can see the troubleshooting chart just below the installation details. The SH code that you see on your Tekonsha PRIMUS IQ brake controller indicates there is a short somewhere on the brake output circuit when idle, or when the brake pedal is not being pressed. Tekonsha states that this issue can sometimes be caused by some test lights if you are using test lights. To troubleshoot this issue, start...
    view full answer...

  • Comparison Between the Tekonsha P2 # 90885 and Primus IQ # TK90160 Electronic Brake Controllers
  • The Prodigy P2 brake controller # 90885 and the Primus IQ # TK90160 share some basic features, but there are many differences. The most obvious ones are the displays and appearances of the units, which are connected to the usability of the brake controllers while towing. The P2 has a brighter, light-colored LED display that is easier to read than the red LED display on the Primus, and the P2 also features a rotary lever for the manual braking feature, while the Primus uses an older style...
    view full answer...

  • Where To Connect The Brake Controller To The 7-Way Trailer Connector On The Tow Vehicle
  • On the 7-way connector, that is on your vehicle, the pin you will connect the brake controller wire to is the (2) Blue pin. If you are looking at the inside (back) of the 7-way connector, it will be the pin at the 7:00 position. Looking at the 7-way from the outside (front) it will be at the 5:00 position. The wiring installation is the same on all of the of the brake controllers. I am including a picture of a 7-way and it shows the functions of each pin. You will want to make sure that...
    view full answer...

  • Installing an Electric Trailer Brake Controller on a 2008 Chevy Silverado 1500
  • Your 2008 Chevy Silverado will have the wiring for a brake controller located under the dash, below the steering column and to the left of the brake pedal. The wires are held together by a white tag that may also list the functions of the wires. If not, you can follow the color/function code below. Brake Controller White to Truck White (ground) Brake Controller Red to Truck Light Blue (stop light) Brake Controller Blue to Truck Dark Blue (electric brake output) Brake Controller Black...
    view full answer...

  • What are the Differences Between the Prodigy P3 and Primus IQ Brake Controller
  • There are quite a few differences. The ones you can see easily on the outside are the display and control buttons. The P3, part # 90195, uses a multi-color LCD to provide more information where as the Primis IQ uses basic LED numbers like what you would have on your digital alarm clock. The P3 uses a rotary lever on the underside for a manual over ride where as the Primus uses the older slide design that some people have problems with the slide sticking depending on how they grip and...
    view full answer...

  • Can Brake Controller Cause ABS and Brake Warning Lights of Tow Vehicle to Come On
  • I spoke with my contact at Tekonsha, who tells me that if the brake controller has been properly installed, the brake controller will have nothing whatsoever to do with the ABS system of your vehicle. If the controller was hardwired into the tow vehicle (as opposed to using a plug-in connector) there's a very slight chance that if the red wire from the brake controller could've been tapped into the wrong circuit. The red wire should be tapped into the circuit coming off the brake stoplight...
    view full answer...

  • Recommended Hitch Trailer Wiring and Brake Controller to Tow Pop-Up Camper with a 2012 Jeep Compass
  • You son's Compass can be equipped to tow that pop-up camper, as long as its fully loaded and ready to tow weight does not exceed the towing capacity of the Compass, which is 2,000 lbs according to my research. For a hitch, I would recommend the Hidden Hitch Class III, part # 87606. You would also need a ball mount, part # 2753 and the appropriately-sized trailer ball, # 19261 for a 1-7/8 inch ball or # 63845 for a 2 inch ball. The coupler on the pop-up should say which size is needed. For...
    view full answer...

  • Troubleshooting Weak Trailer Brakes That Won't Lock Up with Override Lever of Controller Slid
  • This could be a magnet wiring problem. It is unlikely that the magnets are bad on newer assemblies, but if the wiring is not properly connected, it could cause problems. Check to see that the magnets are properly grounded to a clean, bare metal surface free of corrosion. A bad ground would not allow the circuit to be complete and lead to the brakes not performing like they should. I also recommend checking the trailer side connector ground and the vehicle side connector ground. Another...
    view full answer...

  • Location of Brake Controller Connector on 2005 Ford F150
  • The connector for installing your brake controller is located under the dash. Directly under the steering column, you will see the diagnostic port. The port for the controller is located above and behind, as you can see in the photo I've provided. To wire the controller, you'll need the brake controller wiring adapter, part # 3035-P. Simply plug one end of the controller into the rear of the Primus brake controller, and the other end into the connector under the dash. For more information,...
    view full answer...

  • Troubleshooting a Tekonsha Primus Brake Controller Displaying 0.0 and Not Braking
  • It sounds like there might be some other fuses that could have blown, or there are some shorts on your brake controller/7-way circuits. It is hard to know exactly where the problem lies, but the first thing I would check would be to test the manual override lever when the trailer is connected and see if it will apply the trailer brakes. If it does have voltage then I would check to make sure brake switch circuit (red wire) sees voltage when the brakes are applied. If not, then you have...
    view full answer...

  • What Do the nc and c Message Codes Indicate on a Tekonsha PRIMUS Trailer Brake Controller
  • On the Tekonsha PRIMUS Brake Controller, # TK90160, a message that reads nc means no trailer is connected. A message of c means that a trailer is connected. If you are getting the nc code even if a trailer is connected, it could be caused by one of, or a combination of, several possibilities. Trailer connected with open circuit on brake line. Trailer connector disconnected or corroded. Loss of trailer brake magnet ground. I have included a link to the installation details for the...
    view full answer...

  • Which is Best Digital Brake Controller at the Lowest Cost for a 2000 Chevrolet C1500
  • Brake controllers are divided into two categories, time delayed like the Draw-Tite Activator II Electric Trailer Brake Controller, item # 5500, that you mentioned, and proportional like the Tekonsha PRIMUS IQ Electronic Brake Controller, item # TK90160, which has a digital display. These are the two lowest cost digital readout controllers in each category. A time delayed brake controller sends a predetermined amount of braking power to the trailer and then there is a delay as the unit...
    view full answer...

  • Older Generation Primus Cequent Brake Controller User Manual
  • I was able to find the older style Primus Brake Controller part number 39515 installation instructions and I attached the picture to the right for you to check out. The flipper switch on the side of the controller does control the aggressiveness of the brake application. With the lever flipped back away from the front of the controller the braking will be delayed, straight down will be normal, and towards the front is aggressive.
    view full answer...

  • How to Find the Stop Light Switch to Install a Brake Controller on a 2007 Dodge Ram 1500
  • The cold side of the brake switch is the part of the brake switch, located above the brake pedal, that does not have constant power going to/from it. When installing a brake controller like the Tekonsha PRIMUS IQ Electronic Brake Controller, # TK90160, you will need to attach the red wire on the brake controller to the wire on the cold side of the brake switch that carries a signal ONLY when the brake pedal is pressed. It is possible that this wire is blue with white tracer, but manufactures...
    view full answer...

  • Troubleshooting a P.L. Error Code on a Tekonsha Primus IQ Brake Controller
  • The P.L. code that you are seeing on your Tekonsha Primus IQ Brake Controller part # TK90160 means there is a power interruption while the brake pedal is depressed. This typically is caused by a bad or insufficient ground. You can test this by attaching the white wire from this controller directly to the negative side of a vehicle battery to see if the problem goes away. I also attached an FAQ article on troubleshooting brake controller installations for you to check out.
    view full answer...

  • Brake Controller Installation on 2008 Grand Cherokee Diesel
  • According to my contact at Tekonsha, there is not any special procedure or considerations for a brake controller installation on Diesel equipped models versus the gas-engined counterparts. To install your brake controller, you will look for a light green wire bundled up under the dash or behind the drivers side kick panel that would be next to your left foot while driving. This wire will connect the brake controller output (blue wire) to the 7-way. The power (black wire), ground (white...
    view full answer...

  • Tekonsha Primus IQ Trailer Brake Controller # TK90160 Shows No Connection to Trailer
  • Your Tekonsha Primus IQ # TK90160 brake controller will display the NC message (indicating the trailer is not connected) for any of several possible reasons: if the trailer is not connected, if the connector has corrosion, if there is an open circuit on the brake line, if the trailer brake magnet loses its ground connection to the trailer frame or if the brake magnet is malfunctioning. Although trailer lighting functions are carried on the same 7-way connectors, since they are on separate...
    view full answer...

  • Location of Brake Controller Installation Connector on 1995 Dodge Ram
  • I am assuming that you are speaking of the installation connector for a brake controller. It is located on top of the white box on the firewall behind the emergency brake pedal. To install your brake controller, you will also need a Wiring Adapter, part # 3020-P. If your truck isn't equipped with the factory 7-way trailer connector, the plug might not be present. If the connector is not there, you'll need to hardwire the controller using our brake controller installation kit, part...
    view full answer...

  • Location of Brake Controller Connector 2016 Ford F53 Motorhome Chassis
  • The brake controller connector is located on the left side of the steering column support, as shown in the provided photo. You'll need the # 3034-P brake controller wiring harness.
    view full answer...

  • What is the Difference Between the Primus IQ Brake Controller and the Prodigy P2 Brake Controller
  • There are quite a few differences. The ones you can see easily on the outside are the display and control buttons. The P2, part # 90885, uses a rotary lever on the underside for a manual over ride where as the Primus uses the older slide design that some people have problems with the slide sticking depending on how they grip and operate the slide. The P2 has several buttons on the face for adjusting settings and navigating through the menus. The Primus IQ uses a dial and one button to...
    view full answer...

  • Where to Find Brake Controller Connector on 2010 Ford F250 Super Duty
  • The tow package connection port on your 2010 F250 is clipped to the rear of the coin tray located in the center console. The coin tray will need to be temporarily removed so the connector can be detached from the rear of the tray. The 3034P can be plugged in, and the wires ran out the side of the center console as desired. Our friends at Tekonsha kindly provided a photo showing the location of the tray.
    view full answer...

  • Locating Brake Controller Connector on 2000 Ford F350
  • Although the grey plastic brake controller connector socket is typically located behind that panel located under the steering column, there is one alternate location I am aware of. Follow the accelerator pedal all the way up under the dash. Just to the right of where the throttle cable attaches to the end of the pedal, there is a body strut bolted to the firewall. The connector is sometimes pinned to the side of the strut, as shown in the photo I edited for you. It is unlikely but possible...
    view full answer...

  • Brake Controller Installation on 2015 Dodge Grand Caravan SXT
  • My contact at Tekonsha is unaware of a 2015 Grand Caravan that has a factory 7-way, we're guessing that the 7-way you have might have been a dealer installed option. If I had to guess, I'd say that the blue wire you located is the output circuit for the brake controller that would need to run through the firewall and connect to the blue output circuit wire of the brake controller. The power, ground and stoplight switch connections for the controller would need to be manually completed...
    view full answer...

  • Installing 7-Way Trailer Connector and Brake Controller in 2014 Dodge Grand Caravan
  • To install a 7-way trailer connector on your van, you'd first install a functional 4-pole connector, like part # 118534. Once that's installed, you can install a 7-way by plugging the # 37185 adapter into the 4-pole. Once the white wire is grounded, the lighting functions on your 7-way will all be functional. If your trailer has electric brakes, and you want them operable you'll need to install a brake controller. For a basic but easy to use controller, I'd recommend the Tekonsha Primus,...
    view full answer...

  • Differences Between Tekonsha Voyager # 39510 and Prodigy P2 # 90885
  • There are a few differences between the two controllers. The Voyager has been around for a looooooooong time. It uses an internal pendulum to determine how quickly the tow vehicle is braking. In order to operate correctly, this level of the pendulum needs to be adjusted. The Voyager also lacks a digital display which makes troubleshooting more difficult. The controller does not provide boost settings and is not compatible with electric over hydraulic braking systems. The Prodigy P2...
    view full answer...

  • How to Install a Tekonsha Primus IQ Brake Controller in a 2015 GMC Sierra 1500
  • Yes there is, to install the Tekonsha Primus IQ Trailer Brake Controller # TK90160 in your 2015 GMC Sierra 1500 all you need is the brake controller install harness part # 3016. I attached an install video for you to check out as well.
    view full answer...

  • What Does the SH Error Message Mean on a Tekonsha PRIMUS IQ Trailer Brake Controller
  • On the Tekonsha Primus, # TK90160, the SH error message means that the brake controller is sensing a short on the brake wire (blue) when at idle. The instructions I have linked also state that some test lights and non-Tekonsha testers can cause this problem. The most likely cause is a dirty or corroded trailer connector. Inspect the truck and trailer side connectors for dirt and corrosion. Also check where the wires attach to the back of the connectors. On the trailer check the main...
    view full answer...


Do you have a question about this Brake Controller?






Why etrailer.com?

At etrailer.com we guarantee:


Highest quality brake controller for the best price.


Real product know-how.

  • We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. This helps you get the right product the first time.
  • Every day our teams test, review, assemble and install our products. Our modern installation facilities allow our expert installers and customer service representatives to actually install and use the items we sell, so you can get real advice, from a real person who has the knowledge and expertise needed to solve your problem.

Most detailed, accurate brake controller information available.

  • Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information.

Information for this part was:

Test Fit:
Joe V
Photos by:
Theodore B
Expert Research:
Michael L
Video Edited:
Zack K
Expert Research:
Sarah L
Video Edited:
Andrew K
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Video Edited:
Joshua S
Test Fit:
Nicholas E
Video Edited:
Jacob T
Expert Research:
John H
Updated by:
Adele M
Expert Research:
Brandon M
Video Edited:
Andrew L
Expert Research:
Adam R
Video Edited:
Kathleen M
Video Edited:
Mike H
Updated by:
Laura H
Video Edited:
Dustin K
Installed by:
Cole B
Test Fit:
Shane T
Expert Research:
Rachael H
Expert Research:
Jeffrey L
Test Fit:
Alan C
Video Edited:
Sue W
Test Fit:
Randy B
Video Edited:
Chris R
Photos by:
Zach O
Updated by:
Sarah W
Test Fit:
Jared G
Video by:
Zach D
Test Fit:
Andrew S

Installations, made easy.

  • We love helping people.
  • We have the most highly trained customer service, hands-on experience, step by step videos and installation instructions. We are prepared to answer any question, give advice, or troubleshoot any problem you come across.

Fast shipping.


Personalized service for life.

  • We provide one-on-one, personalized service from the ordering process through the life of your product.

Trusted since 1946.

  • We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service.

Info for this part was:


Test Fit:
Joe V

Photos by:
Theodore B

Expert Research:
Michael L

Video Edited:
Zack K

Expert Research:
Sarah L

Video Edited:
Andrew K

Expert Research:
Robert G

Expert Research:
Patrick B

Expert Research:
Michael H

Expert Research:
Jeff D

Expert Research:
Reno H

Expert Research:
Jameson C

Video Edited:
Joshua S

Test Fit:
Nicholas E

Video Edited:
Jacob T

Expert Research:
John H

Updated by:
Adele M

Expert Research:
Brandon M

Video Edited:
Andrew L

Expert Research:
Adam R

Video Edited:
Kathleen M

Video Edited:
Mike H

Updated by:
Laura H

Video Edited:
Dustin K

Installed by:
Cole B

Test Fit:
Shane T

Expert Research:
Rachael H

Expert Research:
Jeffrey L

Test Fit:
Alan C

Video Edited:
Sue W

Test Fit:
Randy B

Video Edited:
Chris R

Photos by:
Zach O

Updated by:
Sarah W

Test Fit:
Jared G

Video by:
Zach D

Test Fit:
Andrew S

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.







Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviews etrailer.com reviews

All images, layout and content copyright etrailer.com