Yates Side Guide Roller for Boat Trailers - Heavy-Duty Rubber - 9" Long - 1/2" Shaft

See what our Experts say about this Yates Rubber Boat Trailer Parts

• Replacement Side Guide Roller for Boat Trailers
  We have the Yates Side Guide Roller for Boat Trailers that are 9" Long with 1/2" Shaft, # YR9202-4. And the 12" Long - 5/8" Shaft Yates Side Guide Roller for Boat Trailers, # YR12243-5. For replacement parts of this type, the roller, roller shafts and caps are sold separately, not as a complete assembly. But you can link to each of the shafts, caps etc. from the roller product page. Please let me know the length needed if one of the above two options does not fit. Or, follow the link...
  view full answer...
• Bow Roller Solution for Jon Boat that Has Flatter and Wider Bow
  Based on what you described you might be best served with a keel roller assembly like the # CE10455G which is 12 inches long and has a pretty low angle to the roller which sounds like would be a great match for the contour of the bottom of your boat.
  view full answer...
  
• Is the Yates Side Guide Roller for Boat Trailers # YR9202-4 One or Two Pieces
  The Yates Side Guide Roller for Boat Trailers # YR9202-4 is one piece. The lines you see are the seam left from the mold that was used to create the roller.
  view full answer...
• Shafts for Rollers on Pontoon Boat Trailer are Welded On
  I have included a link to the rollers we have but looking through them none separate to fit the welded-on shafts you have on your pontoon boat trailer. Your remaining option is to remove the old ones and bolt some new ones on so that you don't run into this problem again. I have also included a link to the brackets and shafts we carry.
  view full answer...
• How to Determine the Correct Replacement Boat Trailer Roller Shaft, Roller and Caps
  The Roller Shaft with Pal Nuts for Boat Trailer Rollers # CE10705A (12-3/4"), Yates Side Guide Roller for Boat Trailers # YR9202-4 and Rubber End Cap 2" for 1/2" Shaft by Dutton-Lainson # DL21560 will provide you with the same length (9") roller and overall length of 16.75" as your current set-up and all work together. The difference is in the length of the roller shaft. Your current one being 13-1/4" and this one being 12-3/4". This will most likely work, but it would just depend on the...
  view full answer...
• Replacement Side Guide Rollers and Endcaps For a Boat Trailer
  It appears you have the Yates Side Guide Roller # YR9202-4 with the Yates Endcap # YR220-4. The endcap is held in place on the 1/2" Shaft # CE10705A by a Cap Nut # CE10800. These are a press fit on the shaft and can take a bit to get the cap nut off. As you mentioned the top portion is just falling apart as you touch it it would be easiest to just cut it off to gain access to the cap nut which you can then use a 1/2 open end wrench to get under the cap nut and pry/hammer off the nut.
  view full answer...
• Available Boat Trailer Keel, Spool and Bow Rollers
  The smallest keel rollers we offer are 5-inches in length and they fit either 1/2-inch or 5/8-inch diameter shafts. We do have spool and bow rollers too in various sizes but none fit on a 3/8-inch shaft so you will be better off replacing the entire assembly with an item like # CE32110G. The linked page will allow you to browse through all of our rollers.
  view full answer...

Do you have a question about this Boat Trailer Part?