See what our Experts say about this Yates Rubber Boat Trailer Parts

• How To Install New Wobble Rollers, Washers, And Retaining Rings
  The way to install the new # YR343R-6P roller is pretty simple. You'd can use pliers or channel locks to remove the existing retainer ring and the old washer. Then remove the old roller. install the new roller part # YR343R-6P and washer part # CE10983, and install the new retainer ring part # CE10981 by slipping it over the shaft and crimping it with the pliers or channel locks. This roller is designed to work on a 3/4 inch diameter shaft.
  view full answer...
• Availability of Replacement Yates 343R Wobble Rollers
  We have the Yates 343R wobble roller replacement you are looking for with the part # YR343R-6P which would work great for you.
  view full answer...
• Tool Recommendation for Installing Retainer Ring for Wobble Rollers
  Sounds like you are looking for a way to secure the # CE10981 to the shaft for the installation of the part # YR343R-6P. A decent set of pliers like the part # PTW88003 would do the trick. Or a set of channel locks.
  view full answer...
• How to Install Wobble Rollers on Older Boat Trailer
  If you have enough of the shaft still intact then you can use the CE Smith Wobble Roller Retainer Ring # CE10981 and a Wobble Roller Washer # CE10983 for the Yates Ribbed Wobble Roller # YR343R-6P for a 3/4" shaft. Otherwise you may need to get a new shaft and use the above products to secure the rollers. To install the retainer ring you can use ring pliers like part # PTW88003.
  view full answer...
• Can Cotter Pin Be Used to Secure Yates Ribbed Wobble Roller YR343R-6P
  If the 3/4-inch shaft where you intend to install Yates Ribbed Wobble Roller # YR343R-6P has a hole for a cotter pin, then yes, you can secure the wheel that way and I suggest placing a flat washer between the roller and the cotter pin to avoid any potential for abrasion.
  view full answer...
• Replacement Boat Trailer Rollers That Fit 3/4" Shaft
  We have a few options for replacement rollers that fit 3/4" roller shafts. The Yates Ribbed Wobble Roller # YR530R-6P is 3" wide, 5" in diameter, and fits 3/4" shafts. The Yates Ribbed Wobble Roller # YR343R-6P is also 3" wide and fits 3/4" shafts, but has a diameter of 4-3/8". These two roller options made of heavy duty rubber and are considered ribbed design, which provides excellent traction for slimy hulls. Another option is the Yates Wobble Roller # YR440R. This measures 4-1/4" wide,...
  view full answer...
• Can a Ribbed Wobble Roller be Used in Place of a Regular Wobble Roller on a Boat Trailer
  The Yates Ribbed Wobble Roller, # YR343R-6P, is 3 inches wide when compared to # YR440R which is 4-1/4 inches wide. If the 3 inch width will still work for your application then you can use it in place of the # YR440R roller.
  view full answer...
• Replacement 4-3/8 Inch x 3 Inch Wobble Roller for Boat Trailer
  The Yates Ribbed Wobble Roller part # YR343R-6P is exactly what you need. The roller is 4-3/8" diameter x 3" wide and has a 3/4" diameter shaft. This roller is constructed of a heavy-duty rubber that is made right here in the U.S.A. I have attached a review video on the above roller for you as well. If you need any other parts for your boat trailer please feel free to let me know what those are and I would be happy to offer my recommendations.
  view full answer...
• What Diameter Shaft Does Yates Wobble Roller 343R Use
  The Yates Ribbed Wobble Roller part # YR343R-6P that you have actually uses a 3/4 inch shaft or if you had the part # YR343R-5P the shaft diameter would be 5/8 inch. I'd maybe try measuring the diameter again and going with the wobble roller that matches what you are in need of.
  view full answer...
• Replacement Wobble Rollers and U-Bolts for a 1989 Venture Boat Trailer
  In order to determine the correct replacement wobble rollers for your 1989 Venture boat trailer I would need to know the overall diameter of the roller in addition to the diameter of the shaft. For example, the Yates Ribbed Wobble Roller part # YR343R-6P has a 4-3/8" overall diameter with a 3/4" shaft. Once you can let me know what the above two dimensions are I would be happy to inform you of which replacement wobble rollers you need for your boat trailer. I have also attached our selection...
  view full answer...
  
• Boat Trailer Wobble Roller with 4-1/4 Inch Diameter, 3 Inch Width that Fits a 3/4 Inch Shaft
  Wobble roller # DL21564 is a close match to what you need. It has a 4-1/4 inch diameter and it is 3 inches wide. But it fits on a 7/8 inch diameter shaft and the hub center is 1-1/2 inches wide. Wobble roller # YR343R-6P could work. It is 4-3/8 inches diameter and 3 inches wide. It fits a 3/4 inch shaft but the hub center is 1-1/2 inches wide. But if the overall width is 3 inches then the hub center width should not matter.
  view full answer...
• Replacement 4-3/8 by 3 Inch Wobble Rollers for a Boat Trailer
  We have a couple of wobble rollers that are 4-3/8 inch diameter and 3 inches wide. We have # YR343R-6P which fits on a 3/4 inch shaft or # YR343R-5P that fits a 5/8 inch shaft. Roller # YR343R-6P is the best option since the center hole is slightly under 7/8 of an inch to fit a 3/4 inch shaft. Roller # YR500YW-7P has a center hole slightly under 1 inch to fit a 7/8 inch shaft but the diameter is 5 inches. If the slightly larger diameter would work then this is a good option. Otherwise...
  view full answer...
• Non-Marking Wobble Rollers to Replace Yates 343R
  For a non-marking wobble roller to replace the ones you have now you'd need to go up to the 5 inch size like the part # YR500YW-8PEZ which has a 1 inch shaft diameter. I do not know specifically what shaft diameter you need so you'd need to determine that and go with the correct size. If not 1 inch I attached a page that has all of the different sizes that are non-marking and 5 inch.
  view full answer...
• Removing a Retaining Ring from a Wobble Roller
  Probably the easiest way to remove a retainer ring, such as # CE10981, to replace a wobble roller is to grip one end with some vise grips and the other end with some pliers. Then twist in opposite directions to make the opening wide enough for it to slip off. If you have a rotary tool with a cutting attachment it would make short work of it.
  view full answer...
• Availability Of Non-Marking Wobble Roller To Replace Yates Ribbed Wobble Roller YR343R-6P
  We have just what you need. To replace the Yates Ribbed Wobble Roller - Heavy-Duty Rubber - 4-3/8" Diameter - 3/4" Shaft # YR343R-6P with a roller that is non-marking you will need the # YR500YW-6P. Now the # YR500YW-6P will be 5/8" larger in diameter, which will lift you boat 5/16" higher on your trailer but this will not cause any issues. I included a video of the # YR500YW-6P for you to take a look at.
  view full answer...
• Replacement Wobble Roller For A 1 Shaft on an EZ Load Trailer
  The Yates Ribbed Wobble Roller - Heavy-Duty Rubber - 4-3/8" Diameter - 3/4" Shaft Item # YR343R-6P is for a 3/4" shaft. The correct replacement wheels you need is the Yates Ribbed Wobble Roller - Heavy-Duty Rubber - 5" Diameter - 1" Shaft Item # YR530R-8P.
  view full answer...
• Dimensions of Yates Heavy-Duty Rubber Ribbed Wobble Roller YR343R-6P
  The Yates Heavy-Duty Rubber Ribbed Wobble Roller # YR343R-6P is 3-inches wide and 4-3/8-inches in diameter. The inner hole diameter is slightly under 7/8-inch in order to fit a 3/4-inch diameter roller shaft.
  view full answer...
• Boat Trailer Wobble Roller Recommendation to Fit 3/4 inch Diameter Shaft
  We have wobble rollers specifically designed for 3/4 inch shafts like yours. For that we have the part # YR343R-6P which has a center hole diameter just slightly under 7/8 inch to fit the 3/4 inch shaft the way it needs to. If you need a washer to go along with it you'd need the part # CE10983 and for a retainer ring part # CE10981.
  view full answer...
• Replacement Wobble Roller for Trailer that Has 1 inch Diameter Shaft
  Your best option since you have a 1 inch diameter shaft for your wobble rollers will be the slightly larger 5 inch diameter non-marking wobble roller part # YR500YW-8P as the small size difference won't cause any issue and I don't like to recommend drilling out bushings.
  view full answer...
• Length of Interior Hub Portion of Yates Ribbed Wobble Roller Part #YR343R-6P
  I went to our warehouse and measured the Yates Ribbed Wobble Roller Part # YR343R-6P. The length of the 7/8-inch diameter hub is 1-1/2-inches. This part fits a 3/4-inch shaft, is constructed of heavy-duty rubber and is made in the USA. Please refer to the linked video.
  view full answer...
• Replacement Wobble Rollers for Boat Trailer
  It's sounds as if you're looking for wobble or rocker rollers. I don't have anything with the exact dimensions you mentioned, but the Yates # YR530R-8P in heavy duty rubber or the # YR500YW-8P in TPR (thermo plasticized rubber) come very close. Both rollers measure in at 5 inches in diameter and 3 inches wide. Clips like part # CE10981 are crimped on the ends of the shaft to keep the roller in place. We don't carry a washer compatible with a 1 inch diameter shaft.
  view full answer...