Best Toyota Highlander Watersport Carriers

As all Thule products the Thule universally mounted canoe carrier is great. It came with all required items for safe and easy canoe transportation. There are two straps with pull to fasten for the canoe down, two tie down ropes for each end with nice pull tight and release mechanisms for the cord as well, along with two straps to fasten to the canoe ends used with the pull to tighten cords. The Chevy traverse cross bar had to have the plastic end caps removed for use with Thule canoe carrier. This was because my canoe took up the entire cross bar width to allow for Thule mounts. It is not a big deal to remove the plastic end caps. They only provide a finished stream lined look. Happy and Safe Canoeing

After retiring my 1999 Chevy Silverado 4x4 pickup, I purchased a 2017 Subaru Outback as a replacement vehicle. To transport my 1981 17 foot QT17C Alumacraft canoe on the factory installed roof rack crossbars that came with the Outback, I selected the Thule Portage Canoe Carrier w/ Tie-Downs - Gunwale Brackets - Side Loading - TH819 to do the trick. With one previous transport of the canoe sitting directly on the Outback roof racks, I realized those Outback roof racks were not as durable as the racks on my truck so I sought an improvement to avoid future scuffing and scratching. I did some advance research online and couldn’t be more pleased with this purchase from etrailer.com. I now have a quality product at the right price and these gunwale brackets are a simple solution for this veteran canoe man. The padded brackets grip the canoe and stopped the scratches. The high-quality load straps are nice with the rubber pad that covers the buckle and they easily snug the canoe tight to the racks. I’m also impressed with the bow/stern tie downs that have a very nice ratchet and clip on one end and I secured the supplied hook with a bowline knot to the other end of the ¼ inch rope. The Outback did not have convenient anchor points on the front or back of the vehicle for tie down locations but I found a good solution there as well by ordering the Thule Bow/Stern Tie-Downs - Qty 2 - TH530. This works well with the tie downs I mentioned previously. One limitation to be aware of with the Subaru Outback roof racks and this product is the width of your canoe. My 17-footer measures 34 inches at its widest point at the portage yoke. I had to place the four brackets up tight against the inside roof mounting to achieve the spread and accommodate the canoe placement. The canoe ended up fitting like a glove on the padded brackets. When placing the strap to hold the canoe down to the crossbars, I ran the strap through the vehicles tie down points and then under the crossbars for added security. Total product installation time including securing the canoe can easily be achieved in approximately 20 minutes. I look forward to many more years of safe and happy canoeing. I give etrailer.com an excellent rating for the entire ordering and shipping process on top of the high level of satisfaction with the products I purchased through them. Their customer service and price ensured me that I’ll do more business with them in the future.

Bought a pair of these to go on 59" rhino rack bars on our Outback Wilderness and am really pleased. I left the bars full width - they are not a head banger on the car - and mounted the Hullavators as far outboard as possible which means the kayaks clear the side of the car and wing mirrors without folding them in. I did have to modify one Hullavator to make the Hobie Lynx fit (36" wide Lynx = 36" max Hullavator width)

Two complete shoulder implants, 75 year old combat disabled Marine who is not quite ready to easily quit something I love. This apparatus is a solution in a box. Somewhat high procurement cost is clearly mitigated by perpetuating quantity of life. That being said, I strongly recommend outsourcing assembly and installation… it proved for me to be a somewhat daunting task. “Better to burn out than rust.”

The product is of good construction but probably due to how it fits on my crossbars it needs additional support. The crossbars for my Honda Pilot are wide blade type and these racks seem more appropriate for narrower square type crossbars. Even with the rack fastened very tightly, the rack can twist back and forth. Last year on a trip across Montana the wind was pretty gusty and it caused the front one to pivot quite a bit and we had to pull off and apply a ratcheting strap over the kayak and under the factory rails to ensure it was held tight and wouldn't move again. This year on the same trip we had bad winds but had a roof rack mounted behind these racks giving it support on the tall side. We had to strap it real good to make sure it didn't move. If we hadn't had that additional support behind it and add'l straps we probably would have had more problems. I think if the top metal bracket had a wider channel to fit our crossbars it would be much more stable. The way it is now it just sandwiches 2 metal plates between my crossbar which allows it to pivot under stress.

Loved the racks, seem very durable. Only downside was that the groove made for the crossbeam was quite a bit smaller than my crossbeams, but they still secured down great. You'd have to have a pretty funky set-up for these racks to not work on your vehicle. Having all the straps/tie-downs included was awesome too. Reccomend!

Very easy to install on roof rack. Just be careful not to lose one of the rubber pieces that help protect your board. They can easily fall off of the rope when tying your board to the rack.

With a little help from youtube, this was one of the easiest things I've ever assembled! LOVE my new SUP rack!!

After attempting to mount the individual rack pieces using the “burglar proof” button head screws with the pin in the recess and the short hex wrench with the hollowed out end I discovered that no real burglar would want the rack but would rather have the kayak so the first thing I did after spending 10 minutes trying to insert the hex into the button head screws with the pin inside the recess and attempting to turn the bolts and continually being obstructed by the support pieces and the paint interference on the bolt heads with trying to get the wrench into the recess I knew it was going to be a long frustrating process so I threw them away and purchased new button head stainless steel bolts and a 4mm extended handle hex wrench to turn them. Smartest thing I ever did. You not only have to mount the rack initially but then you have to put the kayak on the roof and remount all pieces again to fit your boat. All kayaks are different to one degree or another. Having to move the individual support and retighten them with the boat on the rack is even more difficult to do than the initial mounting with these “burglar proof” bolts and hex wrench and you will be happy you threw them away before you started the entire process. Try it for yourself at first and then go get the alternate ones. Worth the little investment and stainless steel will not rust away when you want to remove the rack system in the future. Once the rack is on your vehicle and kayak in rack the tie downs supplied are very good quality. Make sure you use the recommended tie down locations and directions, two kayak body ties and ties at front and rear. Due to numerous kayak hull designs it would be nice to have each support pod have a horizontal swivel built into it so it readily conforms to the hull shape. The overall quality of the system should be the last rack you will have to purchase. I only had issues with the supplied bolts and hex wrench. I gave this rack system a three star because of the bolts and hex tool and the individual pods not swiveling and I haven't at this point transported the kayak anywhere so I am waiting to see how it handles long trips with wind loads and constant loading and unloading performances.

They fit well and I feel my Kayak is safe tied down correctly.

looking forward to using my new racks. Thank you E Trailer.

I love my Rack it came when promised and etrailer was great believe me I will be going back to them for anything else I need I am giving them a well deserved 5 stars

Arrived quickly and was very easy to assemble and attach to the roof of my Jeep. Now that I have the initial setup complete with the proper placement of the entire system, attaching and removing the kayaks will be a breeze. Will definitely make hauling our kayaks much easier and safer.

This product is excellent. I have transported my kayak on these J Hooks several times going 70+ mph down the highway. It never moves. The bolts that come with it are short. If you have a thick roof rack, you will need longer stainless steel bolts. Make sure you you orient the blue straps with the buckle on top so you can pull down to tighten it up.

Needed a rack to haul my kayaks on my jeep patriot and this price was unbeatable. Works well, though I did not like using the foam blocks. Good first rack for new kayakers.

We needed a carrier solution that folded down easily because of our garage door height. The Malone Pro2 Kayak Carrier has performed flawlessly over the past year. The kayaks remain stable and never shift even at freeway speeds. The foam blocks fit our crossbar well and offered a rattle free ride, which is nice. The one drawback to this system is how difficult it can be to actually route the straps. Without a ladder, it can be nearly impossible to get the strap over the kayak and hooked into the carrier properly. After you find a system that works for you, it becomes easier but I still think that the stationary carriers are more user friendly in that regard.

These pads worked well on our Yakima RailBar Crossbars- Item #Y00448-0449 that we also bought from etrailer around 2020/2021. Not sure if etrailer carries the exact Yakima Crossbars anymore, but think they have a similar model. Both the pads and crossbars work well to haul our kayak on our 2019 Subaru Forester. etrailer's customer service rocks! We had a lot of questions purchasing both items and they were great to talk to!

The product came quickly and was so easy to install on my existing roof rails! It is absolutely perfect to fit many needs above and beyond my kayaks and paddle boards. They look so good on my new 2019 Jag F-Pace I might leave them on all the time.

I acquired a second kayak and needed a system to fit the factory racks on my 2011 Toyota RAV4. Etrailer.com has always had information on what fits and has always had the item needed for the job. I attached the Yakima BigStack to the top with ease, and, with one other person to hold the kayaks while I secured, tied two of them down for a long road trip to Northern Minnesota. The system worked just fine. The only caveat was in the configuration of multiple boats in the instructions. The diagram has two boats on the same side of the posts, however, I found it more secure to put one on either side ( other reviews of this product on different Internet sites have found similar results.) The boats made it through the trip with no shifting.

Where do I start? I've been whitewater kayaking for 22 or so years now. I've always used used either Yakima or Thule products... Until I bought a 2015 Nissan Rogue with a naked roof. The curvature of the roof and large door jams mean that Yakima and Thule can't make racks for them. I went to a place that does custom installs and again because of the curvature of the roof, they couldn't give me a rack. This meant no kayaking which is really bad news. Enter the Rhino rack system. I purchased the feet, the fit kit, the cross bars and a Yakima "big stack" stacker. The first issue I had is the reccomended size for the Nissan Rogue is only 48 inches. Way too small too haul 4-5 (very light) whitewater kayaks. I called etrailer and they were SUPER helpful, told me I can buy the 65 in cross bars and they'll work fine. I held my breath and placed my order. I was nervous leaving my trusted name brands. The order arrived super fast (they told me it would arrive by Friday but it actually arrived on Thursday) and everything was packaged rock solid. I was impressed. I read the instructions and put the rack system on my car. It took about a hour (it was hot and I worked slowly) but the rack system is SUPER SOLID. I love it. Rhino might have a "forever" customer out of me. -The rack system is very stable. I can't move it with my hands by pushing or pulling. -The rubber stripping you put on the top and bottom of the bar is an awesome added feature AND it reduces wind noise. -Adding the fairing reduced wind noise even further. With four boats on the roof you couldn't hear any extra noise. The ONE thing I dislike is that you need to use the supplied Allen wrench to take the rack on and off the car. It's a small complaint, but other systems I've used in the past don't have them. I paid much less for this system than I would have if I purchased one of the aforementioned systems, but I'm really really satisfied with the product. We will see how well it holds up over long-term use, but it looks awesome!

We are pleased with the Rhino Rack kayak rack. We are able to get 2 kayaks on our 2020 Volvo V60, and we ate using Yakima crossbars. The kayaks ride without any drama, and the orientation of the kayaks make it easy to load and unload.

The Rhino Rack cradles, straps and hardware are all good quality and I have no complaints. The only issue I have, and the reason for only a 4 star rating, is the supplied M6 x 40mm Security Head screws are too long for the factory cross bars on my roof rack. When I first installed the cradles if I had tightened the screws all the way, the ends would have dug into the roof and paint, even before I added the weight of the kayak. In checking, I can purchase some M6 x 25mm Security Head screws from Amazon, but frankly part of me feels that for what I’ve already paid for this kit I shouldn’t have to spend another $15 for the correct length screws, plus the package has 20 screws and I only need 8. However, it appears that is exactly what I will have to do. At least they will be stainless steel, rather than the cheaper material the current screws are. Plus I will have extras for when/if the head strips out. I would suggest Rhino Rack consider included in their kit two sets of screws to meet this need. Keep the length they have, Judy add a set of 25mm. I’m still happy with the purchase but not 100%. I do like how the kayak slides easily on the rear felt lined cradles. Plus Rhino Rack includes every tie down strap that you will need, e.g. one each for the bow and stern in addition to two straps intended to secure the kayak directly to the roof rack cross bars. I would highly suggest you get in the habit of using all four straps, you really don’t need to have a gust of wind lifting the nose and tearing the roof rack off your vehicle. Can happen! My brother-in-law lost his roof rack exactly in this manner. So happy yakking and safe travels down the road. By the way I have paired these cradles with the Rhino Rack RTL002 T-Load Hitch Mounted Load Assist and Support Bar for 2” Hitches also purchased from eTrailer. I’ve attached some photos showing my first and second attempts to solve my dilemma. I need to order the replacement screws. First attempt after dark was a large flat washer, then the next day I added some nuts under the large washer. NOTE: Photos may post in reverse order.

I searched a lot of websites before finding what I needed on etrailer.com for my 2012 Suzuki GV. I was looking for the proper mounts to install a Kayak rack system. Because my vehicle has a built in rail system it was very confusing what was needed. Thank you etrailer for hooking me up with the appropriate parts for the Rhino system, it worked great!

Terrific experience ordering from trailer. Highly recommend this company to anyone seeking to buy rook racks and kayak holders.

On my second attempt to find a carrying rack for a Pelican Mustang 100x recreational/fishing kayak, I took great care seeking out a rack that would provide at least six contact points for the boat. The kicker is trying to get good contact points to securely cradle the shape of the Mustang 100x "twin arched multi chine hull" while also cradling the edge of the deck. Delta kayaks calls a similarly shaped hull a "fusion hull". After doing a ton of google advanced searches for images for a racked up Mustang kayak model, I concluded a J-Style carrier seemed to be a secure solution. The etrailer J-Style - Folding carrier has solved the equation, and for a very reasonable price. Paired with a Sherpa Boat Roller, my 5' 4" wife can load and un-load her Mustang 100x kayak on her own for her afternoon paddles on nearby waterways. Now she needs a cockpit cover to keep out the rain, and her carrying system is complete. And etrailer made it an easy return of the first rack system I tried. Thanks etrailer!

Overall it was a pretty good experience. However I have three suggestions. 1. The washer and wing nut should be one piece. Trying to fit your hand under the rack holding the washer and wing nut trying to screw the two upside down is a challenge. 2. Strapping the kayak down, it’s difficult to get the strap in the middle of the top bar. Perhaps velcro on the top bar and strap would make it easier to begin the tie down. Finally a better video on the proper tie down procedure for the kayak would be very helpful. It’s maybe the most important part of transporting the kayak and the least part of the time spent on the transport instructions.

This rack works perfectly for storing a car roof top carrier box. The rack is very sturdy and installed easily on our concrete block wall (utilized concrete screw anchors that were not included).

The padded racks seem sufficiently sturdy, and are deep enough to hold our very wide-bottomed kayaks. I hope they hold up well outside over time. The hardware pack includes long screws to sink through wallboard into studs, which I couldn't use here. Somewhat curiously, only one strap is provided for each pair of saddles, which is why we've got some cheapie straps securing the upper kayak. A second strap would have been really nice!

The keys are an issue (wish they were metal), but everything else is great! I go sunrise kayaking only and hate putting straps on with cold hands at 3:30 in the morning. I have a Nissan Pathfinder and was able to put this on with another set of Malone J-hooks so that I can have a second kayak when I go with someone. Once the fear subsides of it possibly falling off, you realize how quick and easy this thing is to use. It takes me 1 minute instead of 9-18 minutes to get my kayak up and secure. I have tested it at 75mph without any jiggling or issues. I sat on this in my shopping cart forever and finally pulled the trigger. If you kayak at least 10 times a year or are going at high speeds for extended periods of time in warm weather, totally worth it. If not, well, there are cheaper options out there.

Unfortunately I did not have the best of luck with this product . I spoke with the company multiple times to ensure this would work with my rack. It did not. This system is made to work ONLY on a roof rack . I have a truck with a rack and a slot in the middle . We had to make different bolts and holders to install this. For using 2 Paddleboards we also had to modify the back of the racks holders to actually touch the boards to hold them in place . After the modifications and many many adjustments we have it working and it does hold great.

Here are some more pics. Very happy with the racks, tie downs and pads. Easy to install, very secure. Love the straps. They have protection around the buckle to protect the board and built in velcro to hold the straps together when not in use.

A few more pics to shown the board on the racks. Easy to install. Feel very secure.

For our 3 grandkids we needed a way to carry camping stuff. This works great. It opens from either side, key locked on both. We have hung it from the garage ceiling for easy installation. All the stuff fits well.

One year later I am really happy with my Thule that has been to Lake of the Ozarks and Orlando from our Indiana home. It fits my Subaru perfectly and I ended up buying the Thule ceiling hanger from etrailer which was pricier than many alternatives but is so much sturdier which is important when your kids are walking under it, as well as my Jeep Rubicon which is parked under it. By using the Thule storage bags we have so much room in the car on our trips. My son ended up buying an XXL for his Toyota Sienna and I am looking towards etrailer for an accessory for our Jeep.

Just installed it. So far so good. Ran 2 bike cables side to side with 4 pad locks to secure it for the summer,

I bought these to support an additional kayak that I purchased for my son to use. They matched a similar pair I bought earlier for my kayak. They are affixed to a roof rack that I also purchased from etrailer.com specifically for my 2015 Acura TLX. Etrailer.com is an excellent source for quality products for your vehicle.

This is a simple product bundle for basic transport, I wouldn't go on a freeway with something like this. Maybe the bundle is a bit pricey for what it actually is (some foam and tie-downs). It doesnt really seem to fit my minivan which has a fiberglass top, or fit my small row boat either, so I have not found a use for it. One nice thing is that all the items are kept well and tightly in the product case. It is thin plastic but has held up to lugging around and stayed closed (plastic has some tabs that close it back up). So the various parts of this bundle won't get lost as long as they are put back in the same case they came in. The included instructions are somewhat good (as opposed to not having any instructions at all).

Exactly what I wanted. etrailer never lets me down!

Easy ordering and fast, free shipping. Product was $50 cheaper on etrailer.com than from Rhino Rack themselves. I will absolutely buy from here again.

I’m very happy with this product. Very solid and easily mounted to my Aero bars. Customer service was very helpful-thank you Neil.