# 1
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs
I installed this on my 2015 Honda Accord for the purpose of pulling my small aluminum fishing boat and trailer. Works great!
Drawbar looks great and will be using in next two days. Thanks!
# 2
Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
I am an infrequent trailer user, but getting my daughter home from college was necessary in March. This drawbar fits my hitch and utility trailer well, did exactly what it is supposed to do, and was the last thing to be concerned about right then. I have a '11 Mini Countryman S with a Class II receiver from Mini Fini, (which cost twice as much as a Curt) where the hole is flush with the fake grille near the bottom of the bumper cover, so I needed the long bar to reach out past the bumper. The Curt receiver for that car hangs visible underneath the bumper (ugly), which also increases the lever arm on the receiver beam and would have needed an even taller rise. (Curt take note!) All just part of the kit to create an occasional 1 ton pickup out of my Mini, leaving the "bed" at home most of the time.
Fits perfectly. I just wish you would’ve sent a pin with it because I had to go chase that down and get an aftermarket one at Ace Hardware.
# 3
Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
I was in need of a hitch higher than the standard 3 or 4 inch riser and spoke with Samatha B, after a couple of emails she found a 5 inch riser for my 1 1/4" receiver. Just what I needed and a happy customer. Received very quick and good sturdy quality. Thanks again!
3.5 stars. Product looks like it should perform as advertised, but it arrived with several chips in the paint. This is most likely due to improper surface preparation and cleaning before the powder coat was applied. As you can see in the photos, there is already some surface rust on some of the areas, including the hole for the hitch pin. Ultimately the paint will get scratched up from use, but it would be nice to see some extra attention to detail from the factory.
# 4
Brophy Drawbar for 1-1/4" Hitches - 5-1/2" Rise, 6" Drop - 7-1/4" Long - 3.5K
I just purchased a new hideaway hitch system. But the hitch sits only 15 inches off the ground at best. And, my trailer coupling is 22-23 inches off ground. So l needed 7-8 inches of rise on the new 1.25 inch receiver system. Internet research took me to etrailer and the Brophy hitch. I got 5.5 inches with the Brophy hitch, the highest available for a 1.25 inch receiver I could find. The others are limited to 5 inches max. I added another 1.5 inches with your Curt shock absorbing hitch. Voila, with a combined 7 inches of rise and on level ground the trailer now rides perfectly level!!!! Both parts were very easy to connect. Delivery was speedy. Thank you for saving the day and my investment in an expensive new hideaway hitch!
Quality parts, but the extra rise with this and the Curt Rocker Ball still wasn’t enough to avoid scraping the top of my inclined road while towing my boat.
# 5
Curt Class II Euro Style Drawbar with 2" Ball - 2-5/8" Rise - 3,500 lbs
It isbthe right size and helps with the height difference to make the trailer more even with the back end of my Accord.
Look and quality of the mount is awesome. Beefy in size as well. If using on my particular application, removal of rear diffuser is necessary. If they had extended it another inch it woulda been perfect. 2015 Audi a3 tdi. Wouldn’t let me add a third pic but it’s a finger tip space between the ball and bumper with diffuser removed.
# 6
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 4-5/8" Rise - 3,500 lbs
Perfect for my Honda Fit as it has a low carriage, the Euro shape gave me a few extra inches to tow a small trailer across the country from Oregon to North Carolina with no issues.
Love this hitch. It looks and fits my Optima perfectly. I was really pleased to find a modern looking hitch to fit on my car. Very strong, solid construction. I don't plan to pull a large trailer with my car but this will work perfectly for my utility trailer. Very friendly and helpful customer service and it was delivered faster than I hoped for. Extremely pleased. Thanks...
# 7
Curt Class II Euro Style Drawbar with 2" Ball - 3-1/8" Rise - 3,500 lbs
Incorrectly listed on etrailers as a 3-1/8” rise, when really this is a 5-1/8” rise (marked correctly on the item itself, but listed incorrectly on this website).
I am completely satisfied with the product. Great quality and excellent finish. Prompt shipping and excellent customer service. It is stylish and functional and will meet my needs for towing up to 3,500 pounds. I would definitely do business with this company again!!!
# 8
Draw-Tite Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-3/4" Long - 3,500 lbs
Easy ordering, fair pricing, prompt delivery...product arrived in excellent condition, very heavy duty drawbar for use with by 4ft x 8ft medium duty trailer.
This drawbar was clearly used. See the picture. I asked etrailer about it and sent this picture but the person that replied, Noah, thought it must have been bumped around in shipping. If shipping caused this much damage, it's a poor quality product. If it was, in fact, used, then etrailer lied to me. Either way...not good.
# 9
Curt Class II Euro Style Drawbar with 1-7/8" Ball - 3-1/8" Rise - 3,500 lbs
Service from eTrailer was great, they even wrote to ensure I got the order correct when I ordered a different size hitch cover than the drawbar that I ordered. Picture attached of the somewhat unique application for the Euro style setup I’m using – I’m dragging my race tires to racing events with my 750HP Cobra!
After speaking with an etrailer phone rep, I did some measuring and opted for this Curt Euro-style drawbar. It looks good on my 2018 Kia Niro, and gets the ball height up 2" and back 3" from where my old ball mount was (much too close to license plate and trailer a bit low in front). For my car, it's the perfect match with the Curt trailer hitch.
# 10
Draw-Tite Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 8-1/2" Long - 7.5K
Excellent quality, fast shipping. Finding a metric ball for our international application was a bit difficult. We knew etrailer was the place to go for all things "trailer" related. Very happy with the purchase!
Strong and seems to be well made and well finished. One-inch ball mounting hole. I used this for a Curt hitch mounted on a 2014 Forester and pulls a small Harbor Freight trailer. Perfect height and trailer is level. Warning - don't get their hitch pin, it does not have a hole for a cotter pin, only a weak clip that I would not trust.
# 11
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
I would give five stars but due to what looks like packaging problems the hitch came very marred and the coating chipping off.
Good and strong but not a great angle/height for my application so had to go to a straight line fit.
# 12
Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 9-3/8" Long - 3,500 lbs
I needed to tow a trailer with a 2" ball. My original ball mount has a 1 7/8" ball installed. I had previously tried to change a ball on a hitch and destroyed the nut and damaged the underside of the ball mount. The lock washer had done a great job in keeping the nut from coming off. I dreaded trying to remove my 1 7/8" ball to install a new one that I would only use once. I decided to buy a new ball mount and mount the new 2" ball. This ball mount is so inexpensive that I realized I could have both ball sizes permanently mounted for use in either ball size.
I wasn't sure what type of ball mount I needed for my new Mazda CX-9, so I had to call a representative. The first time I called, the very knowledgeable gentlemen told me exactly how to measure my SUV to figure out the drop I needed. I called back the next day and talked to a lady who helped me figure out exactly what I needed. This is my second purchase from etrailer. The first was a hitch for my old Honda Odyssey, which was also a great experience. The employees are so helpful, the video tutorials on the web site are fantastic and the prices are great. etrailer.com is the first place I go to look for trailer and towing supplies!
# 13
Curt Class II Drawbar - 3/4" Rise, 1-1/4" Drop - 9-3/4" Long - 3,500 lbs
This draw bar in perfect for my John Deere X738 tractor. What I like about it is the ¾” rise it keep the draw bar height at about the same as the factory frame so the attachments height remain level. Thanks for the great product.
Not much you can say about a bar with a piece of flat metal welded to it; well made looks good. What is really important is that e-trailer is fast, friendly and knowledgeable. I've ordered from them anytime I needed a trailer/RV part.
# 14
Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 14-1/4" Long - 6,000 lbs
The Extra Long Ball Mount proved useful immediately upon receipt. Delivery was prompt, and the updates from etrailer.com helped plan transport of several bicycles, simultaneously with a camper trailer. The extended length facilitated use with a Swagman bicycle rack, also purchased via etrailer.com. The product arrived in excellent condition, with correct capacity rating, and works perfectly, and in conjunction with the bicycle rack. I recommend purchases from etrailer.
Product is exactly as described on the etrailer.com website and measurements and dimensions fit perfect. Easy phone order process and prompt delivery, standard shipping arrived 3 business days after the order was placed. The extra long version of the ball mount makes it perfect for me to put on the bike rack while towing my horses.
# 15
Draw-Tite Drawbar for 1-1/4" Hitches - 5" Rise - 10" Long - 3,500 lbs
This is the correct towbar for a Toyota Prius C. The towbars that are available from U-haul (3 1/8") and other hardware stores are too low to the ground for most trailers. I tow my Harley Dyna on a motorcycle trailer behind my Prius C with no problem. Save yourself the grief. I bought three readibly available tow bars until I found the right one. The 5" rise, 10" long works perfectly. This is an incredibly strong drawbar.
Worked perfectly Did have to grind off the paint and a nit of metal to fit in the reciever though.
# 16
Drawbar for 1-1/4" Hitch - 2-5/8" Rise, 3-1/4" Drop - 7-3/16" Long - 3.5K
The hitch works great. The service was excellent!!! I'm going back and having a hitch put on my other car soon. Thank you.
Everything was perfect.! Nice paint, package, and fast shipping.! Im satisfied.!
# 17
Curt Class II Drawbar - 3-1/8" Rise - 9-1/2" Long - 3,500 lbs
Fits my Curt hitch as described (also purchased from eTrailer), but if pushed in too far it gets stuck in the receiver tube. Had to use a wheel puller to get it back out! Just need to push it in an inch or so to the pin holes line up not problem. My only complaint about ETrailer is that they use huge staples to close their shipping boxes. The staples are tough to pull out (get out your screw driver and pliers if you don't have an industrial strength commercial staple puller). My cardboard recycler does not want these dangerous looking staples left in the box, so I need to pull every one of them out!
Very fast delivery, Very low price for this sturdy drawbar... fits my Rav 4 Class II hitch perfectly.
# 18
Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount - 7" Rise to 9-1/2" Drop - 5,000 lbs
We bought this to tow our 3,000 lbs. boat with our Subaru Ascent with a 5,000 lbs. towing capacity. With the OEM ball mount, we could really feel every jolt and jiggle from hard stops, going over bumps in the road, and trailering down dirt roads. However, the dual cushion ball has really improved our trailing experience. Once we get up to speed, we hardly notice we are towing our boat. It's also great because some of the lakes we visit are down dirt roads, and the cushion makes this a much more pleasant experience. I would highly recommend this to anyone towing a boat or larger trailer with a SUV as it maintains that comfortable ride and the jostling of the trailer is much less noticeable.
Rusted within 30 days. The manufacturer refused to warranty the product. I have continued to use it, but it has required some serious rust mitigation and is a flawed product.
# 19
Curt Class III Drawbar - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
A very solid replacement for the stock Bronco hitch. Fits perfectly.
Product appears to be solid but it’s just a paperweight without a locking pin. Since your tow bar doesn’t come with one either it’s just another piece of metal. Product should include locking pin. No satisfied at all
# 20
Convert-A-Ball Ball Mount for 2" Hitches - 10-3/4" Rise, 12" Drop - 7,000 lbs
Needed a large drop hitch to pull my car trailer. This item came quickly and worked perfectly.
This extreme rise ball mount is what I need to make my passenger car into a back-up trailer puller. It is well built and has a welded strut to reinforce the long rise/drop ball mount. The "shock damper" feature is sure to help absorb the leverage movement that a rise/drop ball mount passes on to the hitch receiver itself.
What our customers are saying:
"WOW! I am impressed! I called to place my order and real person answered, spoke perfect English, albeit a slight southern accent, and my order was sent within a day, shipped quickly and I had it a few days later. I saved over a hundred dollars over local and installed it my self. I cant imagine how that they could do any better. THANKS!"